This discussion has been locked.
You can no longer post new replies to this discussion. If you have a question you can start a new discussion

APX 320 not updating firmware and still restarting

hello,

 

i want to ask about APX 320. We have 13 pieces of this machine. 12 from them i update, pair with XG and they are runing fine. But one of them after connected to net, like 12 before, it still restarting. i tried to connect via console (picture1). there is problem with kernel image.

do I have to complain about the device to the seller? is there a possible setting to fix the problem?

 

4426.picture1.txt
U-Boot 2012.07 (Dec 05 2017 - 16:05:06)

smem ram ptable found: ver: 1 len: 3
DRAM:  512 MiB
machid : 0x8010006
NAND:  ONFI device found
ID = 9590dcc2
Vendor = c2
Device = dc
SF: Detected GD25Q32 with page size 4 KiB, total 4 MiB
ipq_spi: page_size: 0x100, sector_size: 0x1000, size: 0x400000
516 MiB
In:    serial
Out:   serial
Err:   serial
machid: 8010006
flash_type: 0
Configurate GPIO setting
Configurate TPM reset from low to high.
Configurate BLE reset from low to high.
Net:
PHY ID = 0x4dd072, eth0 found AR8035 PHY
MAC0 addr:7c:5a:1c:1:c5:b0
eth0
Creating 1 MTD partitions on "nand0":
0x000000000000-0x000020000000 : "mtd=0"
UBI: attaching mtd2 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    126976 bytes
UBI: smallest flash I/O unit:    2048
UBI: VID header offset:          2048 (aligned 2048)
UBI: data offset:                4096
UBI: attached mtd2 to ubi0
UBI: MTD device name:            "mtd=0"
UBI: MTD device size:            512 MiB
UBI: number of good PEBs:        4095
UBI: number of bad PEBs:         1
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     3
UBI: available PEBs:             2167
UBI: total number of reserved PEBs: 1928
UBI: number of PEBs reserved for bad PEB handling: 40
UBI: max/mean erase counter: 11/1
SF: Detected GD25Q32 with page size 4 KiB, total 4 MiB
Hit any key to stop autoboot:  0
Read 0 bytes from volume image to 88000000
No size specified -> Using max size (67170304)
Wrong Image Format for bootm command
ERROR: can't get kernel image!
Read 0 bytes from volume image_backup to 88000000
No size specified -> Using max size (67170304)
Wrong Image Format for bootm command
ERROR: can't get kernel image!
eth0 PHY0 up Speed :1000 Full duplex
err:magicword 200
Status packet sent after ARP request
data abort
pc : [<8733e7e0>]          lr : [<8733e794>]
sp : 871efc38  ip : 00000000     fp : 00000000
r10: 8735e14f  r9 : 00000000     r8 : 871eff60
r7 : 88000000  r6 : 00000000     r5 : 871efc54  r4 : 88000000
r3 : fffffff8  r2 : 00000004     r1 : 00000000  r0 : 87ffffff
Flags: NzCv  IRQs off  FIQs off  Mode SVC_32
Resetting CPU ...

resetting ...

Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset),  D - Delta,  S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.1-00108
S - IMAGE_VARIANT_STRING=DAABANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x00000021
S - Reset status Config, 0x00000010
S - Core 0 Frequency, 0 MHz
B -       261 - PBL, Start
B -      1338 - bootable_media_detect_entry, Start
B -      1678 - bootable_media_detect_success, Start
B -      1692 - elf_loader_entry, Start
B -      5068 - auth_hash_seg_entry, Start
B -      7209 - auth_hash_seg_exit, Start
B -    578513 - elf_segs_hash_verify_entry, Start
B -    694666 - PBL, End
B -    694690 - SBL1, Start
B -    785007 - pm_device_init, Start
D -         7 - pm_device_init, Delta
B -    786532 - boot_flash_init, Start
D -     57471 - boot_flash_init, Delta
B -    848146 - boot_config_data_table_init, Start
D -      3843 - boot_config_data_table_init, Delta - (419 Bytes)
B -    855359 - clock_init, Start
D -      7578 - clock_init, Delta
B -    867436 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:6
B -    870850 - sbl1_ddr_set_params, Start
B -    875946 - cpr_init, Start
D -         2 - cpr_init, Delta
B -    880329 - Pre_DDR_clock_init, Start
D -         5 - Pre_DDR_clock_init, Delta
D -     13176 - sbl1_ddr_set_params, Delta
B -    893643 - pm_driver_init, Start
D -         3 - pm_driver_init, Delta
B -    964275 - sbl1_wait_for_ddr_training, Start
D -        28 - sbl1_wait_for_ddr_training, Delta
B -    980667 - Image Load, Start
D -    138422 - QSEE Image Loaded, Delta - (269176 Bytes)
B -   1119521 - Image Load, Start
D -      1443 - SEC Image Loaded, Delta - (2048 Bytes)
B -   1129822 - Image Load, Start
D -    220161 - APPSBL Image Loaded, Delta - (450356 Bytes)
B -   1350381 - QSEE Execution, Start
D -        60 - QSEE Execution, Delta
B -   1356598 - SBL1, End
D -    663986 - SBL1, Delta
S - Flash Throughput, 2006 KB/s  (721999 Bytes,  359838 us)
S - DDR Frequency, 672 MHz

 

 

thanks

 

matej

 



This thread was automatically locked due to age.
Parents Reply
  • hello,

     

    thanks for reaction, i used flash tool as u said. But when i follow the instruction, there is little problem. After connected apx via cable, then run tool (FW disable), the tool found my APX. When showed info (picture2) about APX, then tool shutdown after 1-2 sec and i couldnt pres FLASH button.

    thanks

    matej

Children
No Data