This discussion has been locked.

You can no longer post new replies to this discussion. If you have a question you can start a new discussion

UTM Version 9.352-6 and 9.318-5 released (Do not install!!)

twister5800 over 6 years ago

DO NOT INSTALL - THE UPDATES ARE FAULTY (Read this thread through!)

News

· Security Update
Remarks

· System will be rebooted
Bugfixes

36115 WebAdmin reflective XSS Vulnerability
36126 OpenSSL security update 1.0.1q

This thread was automatically locked due to age.

rfcat_vk over 6 years ago

Installed on one UTM and 2 more will go in overnight.
This update should quell some of the security questions.

Ian

XG115W - v19 GA - Home

1225v5 6gb ram, SSID, 4 NICs 20w - v19 EAP - on holiday.

If a post solves your question please use the 'Verify Answer' button.
Cancel
Vote Up 0 Vote Down

Cancel
twister5800 over 6 years ago

Updated first 7 customers locally, performed tests, and did 42 this afternoon...all good so far ;)

-----

Best regards
Martin

Sophos XGA 2100 @ Home | Sophos v19 Architect
Cancel
Vote Up 0 Vote Down

Cancel
PeteGaryga over 6 years ago

Anyone else having issues with the Flow Monitor view throwing the error "Backend connection failed, please click Shift-Reload to try again." on the UTM management page?
It's only there since upgrading this morning.
Cancel
Vote Up 0 Vote Down

Cancel
MattTwombly over 6 years ago

I just upgraded this morning and I am receiving the "Backend connection failed, please click Shift-Reload to try again." on the UTM management page as well.
Cancel
Vote Up 0 Vote Down

Cancel
SteveMiller over 6 years ago

I too am seeing an issue with "Flow Monitor view"
Cancel
Vote Up 0 Vote Down

Cancel
Billybob over 6 years ago in reply to SteveMiller

MattTwombly , SteveMiller Can you guys tell us the version number you are using 9.35x or 9.31x? Also, did you try an aditional reboot after the update just to make sure everything synced up properly? (not that it should matter and is still a bug nonetheless)

Thanks.
Cancel
Vote Up 0 Vote Down

Cancel
MattTwombly over 6 years ago in reply to Billybob

My version is 9.352-6 I did try one more reboot after the initial reboot on install. When clicking on the Flow Monitor it is not displaying anything as well. You just get the errors in the background. The errors will keep popping up while clicking on different menus on the UTM page until you log out and log back in.
Cancel
Vote Up 0 Vote Down

Cancel
Amodin over 6 years ago in reply to MattTwombly

Concurrent Connections window on the Dashboard no longer working, just shows a non-existent image location. (9.352-6)

When I brought my Webadmin page up the first time as well, there was some POST error I couldn't read fast enough. Before logging in, it was something about 'tamper on back end'. I will try to find it perhaps in a log file. I could have read it wrong, but I haven't found anything at all in any logs yet. I will have to look tomorrow when I get more time.

UTM - 9.711 | Intel Xeon 4-core v3 1225 3.20Ghz
16GB Memory | 500GB SATA HDD | GB Ethernet x5
Cancel
Vote Up 0 Vote Down

Cancel
AndreasRieger over 6 years ago

Since Version 9.352-6 the Backend Connection hung up, when i open the Flow Monitor.

I can reproduce this on all GWs under my control who have the 9.352-6 installed (SG125W and SG430).

In ATOP the DIsk Usage and The CPU goes to nearly 100% when i open the flow Monitor.

Can anyone else confirm this?

Cheers Andreas

UTM SCE/SCA | Endpoint SCE
Cancel
Vote Up 0 Vote Down

Cancel
DavidWilliams1 over 6 years ago in reply to PeteGaryga

Same problem with Flow Monitor and Concurrent Connections, as reported by others.

Release 9.352-6
Cancel
Vote Up 0 Vote Down

Cancel