ASG 425 Display with homelicense

Question

Hello, 
 I'm using the ASG 425 Rev3 (Core2Duo E6400) Hardware Appliance in a private Network. 
 I got the Home-License running achieved through deleting the ASG File in /etc Folder. 
 Since i did that, the display isnt working anymore. 
 
 Is there any solution for that problem? 
 
 Kindly regards

CS · Accepted Answer

The file /etc/asg is used by the following procedures: 
 - "initasg" (the difference between the ssi* and asg* ) to assign the correct names to the interfaces. After deleting /etc/asg initasg wont work correct anymore. 
 - "utm-lcd" controls the lcd display. 
 - Hardware License is needed, if /etc/asg exists. 
 
 From my old post. It worked with ASG220 and UTM7-8 (pre utm-lcd): 
 1. Install ASG Hardware with ssi****.iso 
 2. rm /etc/lcd.conf (Link to /etc/asg for lcd4linux) 
 3. mv /etc/asg /etc/lcd.conf (because i like the lcd-information) 
 4. Change in /etc/init.d/initasg the line 34 
 ASG_HW_FILE="/etc/asg" to 
 ASG_HW_FILE="/etc/lcd.conf" 
 5. Install HomeLicense via WebAdmin 
 
 Now in UTM9 you should do this: 
 1. Install ASG Hardware with ssi****.iso 
 2. mv /etc/asg /etc/lcd.asg 
 3. Change in /etc/init.d/initasg the line 34 
 ASG_HW_FILE="/etc/asg" to ASG_HW_FILE="/etc/lcd.asg" 
 4. Change /etc/init.d/utm-lcd the line 1 
 ASG_FILE="/etc/asg" to ASG_FILE="/etc/lcd.asg" 
 5. Install HomeLicense via WebAdmin 
 Please test and post the result!

Mark T · Answer

As a followup for anyone. 
 I picked up a UTM 220 for nothing. I applied the home licence and as you would expect, the lcd stopped working. Having fully updated the firmware and patterns I had a look at the lcd. 
 
 I came across this post 
 
 https://martinsblog.dk/sophos-utm-use-hardware-appliances-with-home-software-license/ 
 
 And followed the newer set of instructions. 
 
 Do a &ldquo;vi /etc/asg&rdquo; 
 It creates a new file and then insert: 
 Ex. for SG 210 
 ASG_VERSION=&rdquo;210&Prime; LCD4LINUX_HW=&rdquo;LCD-SERIAL300&Prime; ASG_SUBTYPE=&rdquo;r1&Prime; 
 Ex. for UTM 220 
 ASG_VERSION=&rdquo;220&Prime; LCD4LINUX_HW=&rdquo;LCM-162&Prime; ASG_SUBTYPE=&rdquo;r5&Prime; 
 As you see UTM and SG&rsquo;s have different LCD controller. 
 Now reboot and watch the display cycle through the widgets, you can also see if /etc/lcd.data is being populated. 
 This worked for me.

Scott_Klassen · Answer

Officially, an LCD is unsupported when using a home license. There were several threads on Astaro.org that gave suggesed workarounds, with avrying levels of complexity and success. Unfortunately, most of the data on those forums is currently inaccessible, but is expected to be restored, then ported over to here, soon. So, for the time being, you won't be able to use the LCD.

__________________
ACE v8/SCA v9.3

...still have a v5 install disk in a box somewhere.

http://xkcd.com
http://www.tedgoff.com/mb
http://www.projectcartoon.com/cartoon/1

twister5800 · Answer

Hi, just tested it out, and it works, but it does not cycle the display, through the interface/ram/cpu values, it just stands on one page with the utm version and uptime. 
 I found out that /etc/lcd.data is not being generated on software installs, so you have to create /etc/asg again and remove the id and serial number, then everything works like on a hardware appliance :-) 
 Read here on bottom where it says : Updated: 15/11-2016: 
 http://martinsblog.dk/sophos-utm-use-hardware-appliances-with-home-software-license/

ASG 425 Display with homelicense

Top Replies