Thread Info
  • State Not Answered
  • Locked Locked
  • Replies 16 replies
  • Subscribers 8 subscribers
  • Views 5469 views
  • Users 0 members are here
Options
Suggested
This discussion has been locked.
You can no longer post new replies to this discussion. If you have a question you can start a new discussion

Firmware Question

Perry Pong

Hi all,

At Management|Up2date, it shows "Current firmware version: 9.311-3. Your firmware is up to date."

When I go to "ftp://ftp.astaro.com/pub/UTM/v9/up2date/", I see a "u2d-sys-9.600005-601005.tgz.gpg" file. 

I have already clicked the "Check for Up2Date packages now" button and upload the "u2d-sys-9.600005-601005.tgz.gpg" file manually , but the version hasn't changed.

Doesn't my firewall's firmware is really up to date?



This thread was automatically locked due to age.
Parents
  • 0

    Short answer, no you're not up-to-date.

    You can try downloading ftp://ftp.astaro.com/pub/UTM/v9/up2date/u2d-sys-9.311003-312008.tgz.gpg this update file manually and upload it manually in your webadmin. It's the update from 9.311-3 to 9.312-8.

    Problem is tough, that there are many steps in between your current version and 9.601-5. Did you perhaps just install the system or do you have any firewalls in front of the UTM that might block it's own check for update feature?

    You could also make a backup of your config, download the latest ISO, install that (it's an install from scratch) and then recover from your backup to have the config back. But there might be other ways to try first. Maybe even just try rebooting the firewall and see if that brings a change.....

    Managing several Sophos firewalls both at work and at some home locations, dedicated to continuously improve IT-security and feeling well helping others with their IT-security challenges.

  • 0 in reply to apijnappels

    Hi ,

    I upload the firmware and reboot but it likes not work. Even it says "Up2Date package imported successfully", the dashboard still shows Version 9.311-3

    About the firewall, I just click the "check for up2data packages now" and "update patterns now" button on every day after setup at webadmin.

    ***UPDATE PROGRESS***

    I found a new problems:

    I see a other discuss in community.sophos.com. I use the putty and check path var/up2date/sys. I find that all firmware are here, just the firewall haven't install.

    If I change to auto-update, it notices new firmware detected. But it does not install.

    Does the firmware will install after reboot?

  • 0 in reply to Perry Pong

    Hi Perry,

    there is no auto-update mechanism in the UTM.

    The option is only for downloading the files.

    You have to trigger the update by yourself with direct install or schedule the latest version to install all the updates.

    Best Regards
    DKKDG

  • 0 in reply to DKKDG

    Hi DKKDG,

    Could you please teach me how to install the update at WebAdmin? or it must manually uses auisys.plx ?

    Thanks a lot!

  • 0 in reply to Perry Pong

    Hi Perry,

    no shell access needed.

    Just navigate to the following point in the webadmin

     

    Best Regards
    DKKDG

  • 0 in reply to Perry Pong

    Click on the red line which says 38 Updates...

    Then click on update now. You will master this, I think.

    Best regards

    -

  • 0 in reply to DKKDG

    Hi DKKDG,

    I haven't this OPTION on WebAdmin.

    Following are our screen capture:

    Also, it reduced to 16 updates only. I run auisys.plx 3 times and it starts the installation and stops at version 9.404-3!

Reply Children
No Data
Unfiltered HTML