Central Wireless RADIUS: Roaming Clients between APX320 and APX530 lose connection when on APX530

it was worth a try. I opened a support case and hope they can figure it out 06845353 

we noticed it happens also when roaming between APX320.

Hi LHerzog,

Thank you for sharing the case. We’re following the case and will update the thread.

As an update from the case, the case handler is waiting for availability from your side for a remote session.

what I can see in the WLAN reports from Windows at the time the issue is recreated is:

Funktionsänderung für "{8a3098e1-e242-4933-b6b2-fc7ea64e573c}" (Familie (0x47008000000000): v4, Funktion: Kein, ChangeReason: NoAddress)

In english like:

Capability change on {8a3098e1-e242-4933-b6b2-fc7ea64e573c} (0x47008000000000 Family: V4 Capability: None ChangeReason: NoAddress)

If you search for that there is quite a lot discussion about that on intel. But not on Sophos.

At the time the disconnect starts, in eventlog there is a driver event

7003 - Roam Complete

That is the latest Intel driver used on the affected test computer. Of course this is not the only notebook and WiFi model with that issue.

Device: Intel(R) Wireless-AC 9560 160MHz

PNP ID: PCI\VEN_8086&DEV_9DF0&SUBSYS_00348086&REV_30\3&11583659&0&A3

Guid: {8A3098E1-E242-4933-B6B2-FC7EA64E573C}

Current driver version: 22.230.0.8

Driver date: 5-9-2023

DevNode flags: 0x180200a

As we use mostly Intel WiFi endpoints, I think Sophos will point the finger at Intel. Intel at the device manufacturer and so on.

iPhones also had this connection issue. They also use that 802.1X SSID.

I'm not interested in blaming, I 'd like to know if we can change APX WiFi settings that act like a workaround.

As written earlier, on our grown AP55C infrastructure this has never been an issue.

UPDATE FROM LHERZOG about this case/thread

News from our support case 06845353 as reference in case other users may face such issues.

Sophos WiFi Dev Team has successfully recreated the issue.

• When a client roams from AP1->AP2->AP1, we observe that the client traffic is not getting tagged properly with VLAN, which results in the client not getting the IP address. 
• When Fast roaming is enabled, radius authentication will be skipped when the client roams.
• The client will receive the correct IP address after turning wifi on and off. This is because the client will go through the complete radius authentication where VLAN information will be captured through radius exchanges.
• Disabling the fast roaming is a possible workaround for this issue for now but it comes with the cost of roaming delay.

UPDATE FROM LHERZOG about this case/thread

News from our support case 06845353 as reference in case other users may face such issues.

Sophos WiFi Dev Team has successfully recreated the issue.

• When a client roams from AP1->AP2->AP1, we observe that the client traffic is not getting tagged properly with VLAN, which results in the client not getting the IP address. 
• When Fast roaming is enabled, radius authentication will be skipped when the client roams.
• The client will receive the correct IP address after turning wifi on and off. This is because the client will go through the complete radius authentication where VLAN information will be captured through radius exchanges.
• Disabling the fast roaming is a possible workaround for this issue for now but it comes with the cost of roaming delay.

UPDATE FROM LHERZOG about this case/thread

After further investigation by the development team for CWIFI-13163 “Fast roaming issues - clients lose IP and need to reconnect,” there is an issue with the Wi-Fi driver on the APX that is preventing the VLAN ID from syncing when fast roaming is enabled with dynamic VLANs. When the wireless client moves to a new access point, the packets coming through the new access point are not tagged with the correct VLAN ID. This results in the clients losing their IP address and must reconnect to the access point. To work around this, we recommend disabling fast roaming across the wireless network, this will allow wireless clients to roam between the access points with the correct dynamic VLAN ID. The other way is to set static VLAN assignments instead of using dynamic VLANs on the wireless network and enable fast roaming.