This discussion has been locked.

You can no longer post new replies to this discussion. If you have a question you can start a new discussion

Airprint not working using Sophos XG WLAN with Bridge2LAN Configuration

GernotMeyer over 5 years ago

Hi,

I configured a Sophos XG with WLAN (Bridge2LAN Config).

So my mobile device is in the same LAN/Subnet as the printer is (yes: Airprint is enabled on it).

I simply start my browser on the mobile device and connect to the printers website. So connectivity with tcp is fine.

But airprint is not possible.

Any ideas? Should this be possible in general?

Thanks for hints!

This thread was automatically locked due to age.

Parents

0 LuCar Toni over 5 years ago

Bridge to AP LAN should work with Airprint. This is my understanding of this feature (Bonjour). AP should not drop those multicast / Broadcast packets.

You should start to debug this on AP Level, which most likely requires Sophos Support.

__________________________________________________________________________________________________________________
Cancel
Vote Up 0 Vote Down

Cancel
0 GernotMeyer over 5 years ago in reply to LuCar Toni

Do I need this feature???
Cancel
Vote Up 0 Vote Down

Cancel
0 TimHansen over 5 years ago in reply to GernotMeyer

I believe the feature you're looking for is accessible on the specific wireless network configuration under Wireless Networks. As per this KB, client traffic should be set to Bridge to AP LAN'. The bridge to ethernet feature is a tad different as it will bridge all access point traffic to LAN.

https://community.sophos.com/kb/en-us/132572

Tim
Cancel
Vote Up 0 Vote Down

Cancel
0 GernotMeyer over 5 years ago in reply to TimHansen

OK. Thanks for Info.

The WLAN is already bridge2LAN but Airprint doesn't work.

So we have 5 IOS devices and 3 airprint printer.

But no IOS device is able to connect to any printer.

What can cause the problem?
Cancel
Vote Up 0 Vote Down

Cancel
0 LuCar Toni over 5 years ago in reply to GernotMeyer

Can you show us the whole configuration?

__________________________________________________________________________________________________________________
Cancel
Vote Up 0 Vote Down

Cancel
0 GernotMeyer over 5 years ago in reply to LuCar Toni

WLAN:

Bridge:

FW Rule: It's simply LAN2LAN (any to any).
Cancel
Vote Up 0 Vote Down

Cancel
0 LuCar Toni over 5 years ago in reply to GernotMeyer

Can you replace in the FW Rule the network hosts with "Any"? Those with the black lines.

__________________________________________________________________________________________________________________
Cancel
Vote Up 0 Vote Down

Cancel

Reply

0 LuCar Toni over 5 years ago in reply to GernotMeyer

Can you replace in the FW Rule the network hosts with "Any"? Those with the black lines.

__________________________________________________________________________________________________________________
Cancel
Vote Up 0 Vote Down

Cancel

Children

0 GernotMeyer over 5 years ago in reply to LuCar Toni

Success!!! Thanks.

But it is not understandable!

There was no (dropped) ticket visible.
Cancel
Vote Up 0 Vote Down

Cancel
0 LuCar Toni over 5 years ago in reply to GernotMeyer

Sure it is.

Because Airprint (Bonjour) uses Broadcast / Multicast to find the printer.

So your Firewallrule, which (could be) 192.168.0.0 to 192.168.0.0 will not match.

The traffic is 192.168.0.1 to 224.0.0.0 for example.

XG does not log dropped traffic, which has no matching rule. https://community.sophos.com/kb/en-us/133310

__________________________________________________________________________________________________________________
Cancel
Vote Up 0 Vote Down

Cancel
0 GernotMeyer over 5 years ago in reply to LuCar Toni

OK. Understood. Thanks for help!!!
Cancel
Vote Up 0 Vote Down

Cancel