Open IPv6 Issues / questions

Hi Ben, please see my answers inline below:

Ben said:

- will the fix for issue NUTM-7187 be included with 9.5?

 [BL]: The fix for NUTM-7187 is not included in this current UTM 9.5 beta version. We are actively working on the fix right now though, so as soon as we have a confirmed fix it will be included in a subsequent release.

- is there a fix in the works for IPv6 Connections where the WAN Port is supposed to use an address out of the delegated prefix? Currently users of such ISPs do not get any IPv6 address. (for esxample KPN netherlands)

[BL]: This should be supported today, unless the ISP is doing both stateless & stateful. Is that the case for you? If so, we are fixing that as part of NUTM-7187 as well.

- what about the ability to change/edit the UID for IPv6 Delegation Requests?

[BL]: Unfortunately this isn't part of this 9.5 release.

- what about long standing feature requests such as 6tunnel integration, lets encrypt - is that on the roadmap? Users, myself included had high hopes for 9.5 but this seems to be more than a maintance release.

[BL]: Lets Encrypt is on our current roadmap, but it's mainly planned as a WAF feature. As for 6tunnel integration, it's currently not planned for any specific release.

 

thank you in advance.

 

Hi Bobby,

Normally the ISPs router will then request /48 prefix and use a /64 from that prefix for the wan interface and a /64for the lan interface. So there are no other global ipv6 addresses than the ones from that /48.

On the Sophos UTM, in my case I will only receive a link local IPv6 address via PPPoE. Using a tcpdump I have verified the UTM is not sending out a prefix request after the PPPoE has been established. Is it waiting for a advertised IPv6 address for the WAN interface first before it will do this? Because in this case it will never get it... And thus a IPv6 prefix will never be requested.

If you want to have a look at my Sophos VM, or need some tcpdumps of the PPPoE setup let me know!

Rene

Hi Ben,

I guess I know what could be causing the prefix to change on every reconnect.

I have copied another fix to you UTM (/root/fix-2.2/ep-ipv6-watchdog-9.40-4.gce64053.i686.rpm) which might solve this problem. Please install it and let me know how it goes.

Thanks,

Prakash

Hi René,

Please get the latest fix (/root/fix-2.2/ep-ipv6-watchdog-9.40-4.gce64053.i686.rpm) from Ben.

It has the fix for your issue too. Let me know if it works for you.

In any case, please collect the ipv6.log and system.log files from /var/log and also provide packet captures if possible.

Thanks,

Prakash

Hello Prakash,

thanks again for the swift reply, this fix indeed seems to fix all the issues! It did a rebind on reconnect instead of getting a new prefix. 

I will now let this run for 2-3 days and than report back :)

THANK YOU! :-) and big thanks to any other developer involved in this fix! 

Hi Prakash, Ben, etc :)

Is it possible to receive this hotfix as well? I'd like to test if it now works with XS4ALL. Would love to have my SG125w fully up and running again :)
Since this is in the UTM 9.5 beta board, I can use the beta as base? Or did you install it on the latest 9.4?

Hi,

as long as Prakash is ok with that ill provide you with the patch. I am running on 9.4, i think Rene is running on 9.5 beta. Since the patch only patches the ipv6 watchdog files (i think) you should be OK with 9.5 beta.

Hi SanderRutten,

You are free to get the rpm from Ben.

However, please note that this fix was only verified for 9.411-3.1. But, as Ben said, it should (I am 'pretty' sure it would) work if installed over 9.5 Beta too.

-Prakash

One way to find out ;-)

Hi Prakash,

Good and bad news...

The good news is, I am now getting an IPv6 prefix! YAAY

The bad news. IPv6 traffic is not working yet :( 
In the interfaces overview I am not seeing my link local address anymore on the pppoe wan interface. This was shown before.

Log still shows I get it, but ifconfig does not show this local LL address.  
2017:04:19-19:41:55 gateway pppd-pppoe[27608]: local LL address fe80::3567:15be:c320:d03e
2017:04:19-19:41:55 gateway pppd-pppoe[27608]: remote LL address fe80::2a31:52ff:fe59:9fa6

I am also missing an IPv6 default route.

-- UPDATE
After reverting to the previous version I see the ipv6 LL address again in the interfaces overview, but it does not show up in ifconfig.

Using both versions I am able to ping the remote LL
# ping6 -I ppp0 fe80::2a31:52ff:fe59:9fa6
PING fe80::2a31:52ff:fe59:9fa6(fe80::2a31:52ff:fe59:9fa6) from fe80::8445:1d69:66c2:b895 ppp0: 56 data bytes
64 bytes from fe80::2a31:52ff:fe59:9fa6: icmp_seq=1 ttl=64 time=1.14 ms
64 bytes from fe80::2a31:52ff:fe59:9fa6: icmp_seq=2 ttl=64 time=1.08 ms

-- UPDATE2

After setting a default route connectivity works! :D
# route add -A inet6 default gw fe80::2a31:52ff:fe59:9fa6 dev ppp0

I also noticed the "Internet IPv6" network object is not bound to any interface.

René

Hi René,

Thanks for spending time verifying the fix and for your inputs.

FYI... A few other modules underwent IPv6 related fixes and code restructuring for 9.5 Beta (not just the ipv6_watchdog).

The problems you are seeing could be because of certain missing interdependencies (assuming you installed the latest 9.411 ipv6_watchdog fix over 9.5Beta).

If this is not the case, I will need to take a look at the packet capture (just before and after the pppoe interface is enabled) and also the logs from /var/log  to understand the problem in more detail. Would it be possible for you to provide us the same (via Sophos support maybe)?

However, it could be about a week or so before I can actually work on a fix again (sorry about that..)

Regards,

Prakash

i will test the patch with the 9.5 beta soon (tm), will report back on that also.

edit: test with 9.5 Beta, looking good so far.

i will test the patch with the 9.5 beta soon (tm), will report back on that also.

edit: test with 9.5 Beta, looking good so far.