I have exactly the same error

(APX120) # saveenv
Saving Environment to NAND...
Erasing Nand...
Attempt to erase non page aligned data

This is the system initialization prompts (short U26 pin 8)

U-Boot 2012.07 [Chaos Calmer unknown,unknown] (Nov 02 2018 - 08:13:09)

smem ram ptable found: ver: 1 len: 3
DRAM:  256 MiB
@machid : 0x8010100
NAND:  SF NAND unsupported id:0:0:0:0SF NAND unsupported id:0:0:0:0SF: Unsupported manufacturer 00
spi_nand: Id could not be mapped
SF NAND unsupported id:0:0:0:0SF NAND unsupported id:0:0:0:0SF: Unsupported manufacturer 00
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
0 MiB
MMC:
*** Warning - readenv() failed, using default environment

In:    serial
Out:   serial
Err:   serial
machid: 8010100
flash_type: 0
Hit any key to stop autoboot:  0
No such device
nand - NAND sub-system


(APX120) # printenv
baudrate=115200
bootargs=ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait
bootcmd=bootipq
bootdelay=2
fdt_high=0x87000000
flash_type=0
fsbootargs=ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs
ipaddr=192.168.1.11
machid=8010100
stderr=serial
stdin=serial
stdout=serial

Bricked version of system initialization:

Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset),  D - Delta,  S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.1-00120
S - IMAGE_VARIANT_STRING=DAABANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x00000021
S - Reset status Config, 0x00000010
S - Core 0 Frequency, 0 MHz
B -       261 - PBL, Start
B -      1338 - bootable_media_detect_entry, Start
B -      1678 - bootable_media_detect_success, Start
B -      1692 - elf_loader_entry, Start
B -      5068 - auth_hash_seg_entry, Start
B -      7210 - auth_hash_seg_exit, Start
B -    577089 - elf_segs_hash_verify_entry, Start
B -    694418 - PBL, End
B -    694442 - SBL1, Start
B -    785453 - pm_device_init, Start
D -         7 - pm_device_init, Delta
B -    786898 - boot_flash_init, Start
D -     52811 - boot_flash_init, Delta
B -    843849 - boot_config_data_table_init, Start
D -      3838 - boot_config_data_table_init, Delta - (419 Bytes)
B -    851055 - clock_init, Start
D -      7569 - clock_init, Delta
B -    863098 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:1,Subtype:0
B -    866511 - sbl1_ddr_set_params, Start
B -    871608 - cpr_init, Start
D -         2 - cpr_init, Delta
B -    875989 - Pre_DDR_clock_init, Start
D -         4 - Pre_DDR_clock_init, Delta
D -     13174 - sbl1_ddr_set_params, Delta
B -    889728 - pm_driver_init, Start
D -         2 - pm_driver_init, Delta
B -    959701 - sbl1_wait_for_ddr_training, Start
D -        27 - sbl1_wait_for_ddr_training, Delta
B -    975303 - Image Load, Start
D -    152200 - QSEE Image Loaded, Delta - (297752 Bytes)
B -   1127929 - Image Load, Start
D -      1444 - SEC Image Loaded, Delta - (2048 Bytes)
B -   1138329 - Image Load, Start
D -    223905 - APPSBL Image Loaded, Delta - (458523 Bytes)
B -   1362631 - QSEE Execution, Start
D -        60 - QSEE Execution, Delta
B -   1368853 - SBL1, End
D -    676517 - SBL1, Delta
S - Flash Throughput, 2010 KB/s  (758742 Bytes,  377357 us)
S - DDR Frequency, 537 MHz


U-Boot 2012.07 [Chaos Calmer unknown,unknown] (Nov 02 2018 - 08:13:09)

smem ram ptable found: ver: 1 len: 3
DRAM:  256 MiB
@machid : 0x8010100
NAND:  spi_nand: spi_nand_flash_probe SF NAND ID 0:ef:ab:21
SF: Detected W25M02GV with page size 2 KiB, total 256 MiB
SF: Detected MX25L1605D with page size 4 KiB, total 2 MiB
ipq_spi: page_size: 0x100, sector_size: 0x1000, size: 0x200000
258 MiB
MMC:
In:    serial
Out:   serial
Err:   serial
machid: 8010100
flash_type: 0
Hit any key to stop autoboot:  0
Creating 1 MTD partitions on "nand1":
0x000000000000-0x000010000000 : "mtd=0"
UBI: attaching mtd2 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    126976 bytes
UBI: smallest flash I/O unit:    2048
UBI: VID header offset:          2048 (aligned 2048)
UBI: data offset:                4096
UBI error: ubi_read_volume_table: the layout volume was not found
UBI error: ubi_init: cannot attach mtd2
UBI error: ubi_init: UBI error: cannot initialize UBI, error -22
UBI init error 22
Error, no UBI device/partition selected!
Wrong Image Format for bootm command
ERROR: can't get kernel image!
Creating 1 MTD partitions on "nand1":
0x000000000000-0x000010000000 : "mtd=0"
UBI: attaching mtd2 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    126976 bytes
UBI: smallest flash I/O unit:    2048
UBI: VID header offset:          2048 (aligned 2048)
UBI: data offset:                4096
UBI error: ubi_read_volume_table: the layout volume was not found
UBI error: ubi_init: cannot attach mtd2
UBI error: ubi_init: UBI error: cannot initialize UBI, error -22
UBI init error 22
Error, no UBI device/partition selected!
Wrong Image Format for bootm command
ERROR: can't get kernel image!
resetting ...

You need to retry to break autoboot.
sometimes you need a few attemps.

i prefer to read the nor with in circuit flash.

if you can save the environment you must rebuild all env vars before loading the image file.

Hello Juergen,

Can you post all the env variables that need to be set? I think I made some mistake there...

Hi,

this is the fw_printenv from OpenWRT (root shell from APX120).

setenv BASEMAC 7C:5A:1C:XX:XX:XX
setenv SID P3200XXXXXXXXXX
setenv baudrate 115200
setenv bootargs mtdparts=spi0.1:0x8000000(rootfs) ubi.mtd=rootfs loglevel=1
setenv bootcmd apx_check_reset_button\;run ubiboot\;run ubiboot_backup\;reset
setenv bootdelay 10
setenv ethact eth0
setenv flash_type 0
setenv ipaddr192.168.1.1
setenv machid 8010100
setenv mtddevname rootfs
setenv mtddevnum 0
setenv mtdids nand1=nand1
setenv mtdparts mtdparts=nand1:0x10000000(rootfs)
setenv partition nand1,0
setenv radio0_select_5g 0
setenv serverip 192.168.1.254
setenv stderr serial
setenv stdin serial
setenv stdout serial
setenv store_crashdump setenv crashdump_fix 1
setenv ubiboot ubi part rootfs\;ubi read 0x84000000 image\;bootm 0x84000000#config@4
setenv ubiboot_backup ubi part rootfs\;ubi read 0x84000000 image_backup\;setenv bootargs mtdparts spi0.1:0x8000000(rootfs) ubi.mtd rootfs OLD_IMAGE_BOOTED\;bootm 0x84000000#config@4
setenv wipe_config ubi part rootfs\;ubi remove config\;ubi remove dyn_cfg\;ubi remove dyn_cfg_backup

Thanks!! Managed to fix one APX, now lets try with the second one!

Pietro Verro 

Hi,
can you tell me where to get the APX.v11.0.019-2.uimage ? All pattern files I found only include the newest version 11.0.021...
Thanks Jan

Hi Jan,

You can find it on my OneDrive:

1drv[dot]ms/u/s!Am04YvcSa_CLjLJKKMgj3n9zEQyrUQ?e=4SE2bh

perfect, thank you

Pietro Verro JuergenB 

Hi,

how did you manage to get keyboard inputs in putty ? are there any options needed ? I tried different settings in putty, but I am not able to input any text, after I successfully breaked autoboot.

Thanks Jan

You need a good USB<->RS232 Adapter with 3.3V and need a few attempts to get in to uBoot CLI.

I had some trouble with a USB Hub.
The RS232 Adapter should be plugged into the backside of a PC or directly in your Notebook.

Hi,

I am already in the uBoot CLI, but I cannot input any kind of text in Putty.

I am using the red USB RS232 Adapter with 3,3V (the one, which work for other users), directly plugged into the notebook.
Are there any Putty options, which I need to set ?

No (115200,8N1)

Only use pin 2,3,4 (TX,GND,RX, may be switch TX/RX).

No (115200,8N1)

Only use pin 2,3,4 (TX,GND,RX, may be switch TX/RX).

of course I am using already these pins and settings, but i cannot type any text

If this doesn´t work, you need to get a different USB<->RS232 Adapter.

I had some cheap from ebay, these worked fine with a lot of devices, but not with APX120.

which one are you using ?

I have a few with PL2303HX Chipset, but with Windows 11 i switched to PL2303HXD.

But, yes most of the PL2303HX are some cheap, pink models.

Thank you!!

works with a CP2102 ;-) but now I have the reboot problem as mentioned above.
Do you have also any ideas ?

Hi,

i had a few solutions, but the best was still to setup a XG firewall with a setup for AP.

Next you need to enter APX120 uboot and use these 3 steps.

(APX120) # nand erase.chip clean
(APX120) # tftpboot APX120.v11.0.019-2.uimage
(APX120) # bootm 0x84000000#config@4

After that, the APX120 boots and connects to the XG.
You need to add the APX to the XG and the XG will send a new firmware.
The APX will upgrade by itself.

Thanks to all for your help, only the following steps worked. I had to update to V 2.3.4-5 (maybe because my XG is already on SFOS 20):

1. get into uboot emergency console, change bootdelay, save, reboot
2. enter uboot console, set all env variables, save, reboot, enter uboot
3. erase nand chip, tftpboot APX.uimage (2.1.1.1)

Boot into failsafe (some tries neccessary, hit enter until root) and update with shell script (V 2.3.4-5)

cd bin
wget https://d2apih4urmzzdu.cloudfront.net/v2.3.4-5/APX.uimage
./update_image.sh APX.uimage
reboot

4. APX120 will boot and register with XG, enable APX and wait for final F/W upgrade

Hi,

could you write the correct commands step-by-step, please?

And here my help for the autoboot loop:

.

.

.

S - Flash Throughput, 2008 KB/s  (758742 Bytes,  377680 us)
S - DDR Frequency, 537 MHz

----> here you must bridge GND (J1) and Pin 8 (U26, the first PIN on the left side, under J1)

-----> press any key on the keyboard

U-Boot 2012.07 [Chaos Calmer unknown,unknown] (Nov 02 2018 - 08:13:09)

.

.

Now use the following commands:

setenv autoboot 10

saveenv

Reboot (plug out and plug in)

Best regards,

Stefan