I am using the instructions to unbrick my APX120 from this post, but I have run into issues below:
community.sophos.com/.../unbrick-apx120-break-bootdelay-0-recover-apx120
I can't seem to save the environment variables. When I run the "saveenv"
It says:
Saving Environment to NAND... Erasing Nand... Attempt to erase non page aligned data
I have exactly the same error
(APX120) # saveenv Saving Environment to NAND... Erasing Nand... Attempt to erase non page aligned data
This is the system initialization prompts (short U26 pin 8)
U-Boot 2012.07 [Chaos Calmer unknown,unknown] (Nov 02 2018 - 08:13:09) smem ram ptable found: ver: 1 len: 3 DRAM: 256 MiB @machid : 0x8010100 NAND: SF NAND unsupported id:0:0:0:0SF NAND unsupported id:0:0:0:0SF: Unsupported manufacturer 00 spi_nand: Id could not be mapped SF NAND unsupported id:0:0:0:0SF NAND unsupported id:0:0:0:0SF: Unsupported manufacturer 00 ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0) 0 MiB MMC: *** Warning - readenv() failed, using default environment In: serial Out: serial Err: serial machid: 8010100 flash_type: 0 Hit any key to stop autoboot: 0 No such device nand - NAND sub-system (APX120) # printenv baudrate=115200 bootargs=ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait bootcmd=bootipq bootdelay=2 fdt_high=0x87000000 flash_type=0 fsbootargs=ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs ipaddr=192.168.1.11 machid=8010100 stderr=serial stdin=serial stdout=serial
Bricked version of system initialization:
Format: Log Type - Time(microsec) - Message - Optional Info Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.1-00120 S - IMAGE_VARIANT_STRING=DAABANAZA S - OEM_IMAGE_VERSION_STRING=CRM S - Boot Config, 0x00000021 S - Reset status Config, 0x00000010 S - Core 0 Frequency, 0 MHz B - 261 - PBL, Start B - 1338 - bootable_media_detect_entry, Start B - 1678 - bootable_media_detect_success, Start B - 1692 - elf_loader_entry, Start B - 5068 - auth_hash_seg_entry, Start B - 7210 - auth_hash_seg_exit, Start B - 577089 - elf_segs_hash_verify_entry, Start B - 694418 - PBL, End B - 694442 - SBL1, Start B - 785453 - pm_device_init, Start D - 7 - pm_device_init, Delta B - 786898 - boot_flash_init, Start D - 52811 - boot_flash_init, Delta B - 843849 - boot_config_data_table_init, Start D - 3838 - boot_config_data_table_init, Delta - (419 Bytes) B - 851055 - clock_init, Start D - 7569 - clock_init, Delta B - 863098 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:1,Subtype:0 B - 866511 - sbl1_ddr_set_params, Start B - 871608 - cpr_init, Start D - 2 - cpr_init, Delta B - 875989 - Pre_DDR_clock_init, Start D - 4 - Pre_DDR_clock_init, Delta D - 13174 - sbl1_ddr_set_params, Delta B - 889728 - pm_driver_init, Start D - 2 - pm_driver_init, Delta B - 959701 - sbl1_wait_for_ddr_training, Start D - 27 - sbl1_wait_for_ddr_training, Delta B - 975303 - Image Load, Start D - 152200 - QSEE Image Loaded, Delta - (297752 Bytes) B - 1127929 - Image Load, Start D - 1444 - SEC Image Loaded, Delta - (2048 Bytes) B - 1138329 - Image Load, Start D - 223905 - APPSBL Image Loaded, Delta - (458523 Bytes) B - 1362631 - QSEE Execution, Start D - 60 - QSEE Execution, Delta B - 1368853 - SBL1, End D - 676517 - SBL1, Delta S - Flash Throughput, 2010 KB/s (758742 Bytes, 377357 us) S - DDR Frequency, 537 MHz U-Boot 2012.07 [Chaos Calmer unknown,unknown] (Nov 02 2018 - 08:13:09) smem ram ptable found: ver: 1 len: 3 DRAM: 256 MiB @machid : 0x8010100 NAND: spi_nand: spi_nand_flash_probe SF NAND ID 0:ef:ab:21 SF: Detected W25M02GV with page size 2 KiB, total 256 MiB SF: Detected MX25L1605D with page size 4 KiB, total 2 MiB ipq_spi: page_size: 0x100, sector_size: 0x1000, size: 0x200000 258 MiB MMC: In: serial Out: serial Err: serial machid: 8010100 flash_type: 0 Hit any key to stop autoboot: 0 Creating 1 MTD partitions on "nand1": 0x000000000000-0x000010000000 : "mtd=0" UBI: attaching mtd2 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 126976 bytes UBI: smallest flash I/O unit: 2048 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 UBI error: ubi_read_volume_table: the layout volume was not found UBI error: ubi_init: cannot attach mtd2 UBI error: ubi_init: UBI error: cannot initialize UBI, error -22 UBI init error 22 Error, no UBI device/partition selected! Wrong Image Format for bootm command ERROR: can't get kernel image! Creating 1 MTD partitions on "nand1": 0x000000000000-0x000010000000 : "mtd=0" UBI: attaching mtd2 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 126976 bytes UBI: smallest flash I/O unit: 2048 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 UBI error: ubi_read_volume_table: the layout volume was not found UBI error: ubi_init: cannot attach mtd2 UBI error: ubi_init: UBI error: cannot initialize UBI, error -22 UBI init error 22 Error, no UBI device/partition selected! Wrong Image Format for bootm command ERROR: can't get kernel image! resetting ...
Tried four times, and finally!
But I got this:
Starting kernel ... Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level f - failsafe - /etc/preinit: line 1: telnetd: not found (none) login: Please reboot system when done with failsafe network logins
and then
Starting kernel ... Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level fPlease press Enter to activate this console. Warning: Bad CRC, using default environment (none) login: Booting. (Version: 11.0.021-1) Checking The AP model Starting network configuration for ethernet interface over DHCP. Cloud certificate validation pending. dnsserver entries are missing [
This model (APX120) really needs more QA!
Use this image https://d2apih4urmzzdu.cloudfront.net/v2.1.1-1/APX.uimage
TFTP boot with this in Uboot, then when it shows the failsafe prompt keep pressing enter until you get root.
Hi,
i got two more APX120 with a red LED bug.
tried a few other methods, this one works fine
No need to get root access
But with 11.0.019-2 i had a root access without any failsafe method.
Hi Juergen,
Managed to find the Image (inside the Pattern Update tar). I could link the APX with the Firewall but after reboot I get an error - Volume kernel not found! and I'm back on the uboot console.
Do you have any suggestion?
Hi,
this is the fw_printenv from OpenWRT (root shell from APX120).
setenv BASEMAC 7C:5A:1C:XX:XX:XX setenv SID P3200XXXXXXXXXX setenv baudrate 115200 setenv bootargs mtdparts=spi0.1:0x8000000(rootfs) ubi.mtd=rootfs loglevel=1 setenv bootcmd apx_check_reset_button\;run ubiboot\;run ubiboot_backup\;reset setenv bootdelay 10 setenv ethact eth0 setenv flash_type 0 setenv ipaddr192.168.1.1 setenv machid 8010100 setenv mtddevname rootfs setenv mtddevnum 0 setenv mtdids nand1=nand1 setenv mtdparts mtdparts=nand1:0x10000000(rootfs) setenv partition nand1,0 setenv radio0_select_5g 0 setenv serverip 192.168.1.254 setenv stderr serial setenv stdin serial setenv stdout serial setenv store_crashdump setenv crashdump_fix 1 setenv ubiboot ubi part rootfs\;ubi read 0x84000000 image\;bootm 0x84000000#config@4 setenv ubiboot_backup ubi part rootfs\;ubi read 0x84000000 image_backup\;setenv bootargs mtdparts spi0.1:0x8000000(rootfs) ubi.mtd rootfs OLD_IMAGE_BOOTED\;bootm 0x84000000#config@4 setenv wipe_config ubi part rootfs\;ubi remove config\;ubi remove dyn_cfg\;ubi remove dyn_cfg_backup
Hi,
can you tell me where to get the APX.v11.0.019-2.uimage ? All pattern files I found only include the newest version 11.0.021...
Thanks Jan
