Important note about SSL VPN compatibility for 20.0 MR1 with EoL SFOS versions and UTM9 OS. Learn more in the release notes.

Thread Info
  • State Not Answered
  • Locked Locked
  • Replies 12 replies
  • Subscribers 37 subscribers
  • Views 5445 views
  • Users 0 members are here
Options
Suggested
This discussion has been locked.
You can no longer post new replies to this discussion. If you have a question you can start a new discussion

ASG Home Datendurchsatz sehr niedrig

LoD
Hallo zusammen,

ich habe das Problem,dass die Up- und Downloadraten sehr gering sind, seitdem ich von Lancom 1823 auf ASG Home gewechselt habe.

Vor der ASG hängt eine Fritzbox, die lediglich als Modem dient. In der Oberfläche sehe ich eine Downrate von 16375 kbit/s, im Upload 1131 kbit/s.

Downloads kamen jedoch nie über 300 kbit/s. Also habe ich heute die ASG komplett resettet, um Firewall, Webfilter etc langsam wieder zu füllen und zu beobachten. Die Geschwindigkeit ist aber auch so gering, wenn ich nur den Webfilter für http(s) freischalte. (Caching deaktiviert)

Die Software läuft auf einem ASUS E35M1-M mit 4GB RAM. 
NICs:
WAN == RTL8111/8168B PCI Express Gigabit Ethernet controller
LAN == Intel Corporation 82541PI Gigabit Ethernet Controller

Ist die Zusammenstellung evtl. zu schwach?
 
Kann jemand bestätigen oder besser noch widerlegen, dass mit dieser Hardware der Verbindungsaufbau (Seitenaufbau) und die DL-Rate so niedrig sind?

Weiß jemand wie ich das ändern kann?

Besten Dank vorab

Gruß
LoD


This thread was automatically locked due to age.
Parents Reply Children
  • 0 in reply to trollvottel
    Hallo trollvottel,

    hier ist die komplette Ausgabe von ethtool eth0: 

    Settings for eth0:

            Supported ports: [ TP MII ]

            Supported link modes:   10baseT/Half 10baseT/Full

                                    100baseT/Half 100baseT/Full

                                    1000baseT/Half 1000baseT/Full

            Supports auto-negotiation: Yes

            Advertised link modes:  10baseT/Half 10baseT/Full

                                    100baseT/Half 100baseT/Full

                                    1000baseT/Half 1000baseT/Full

            Advertised pause frame use: No

            Advertised auto-negotiation: Yes

            Link partner advertised link modes:  10baseT/Half 10baseT/Full

                                                 100baseT/Half 100baseT/Full

                                                 1000baseT/Full

            Link partner advertised pause frame use: No

            Link partner advertised auto-negotiation: Yes

            Speed: 1000Mb/s

            Duplex: Full

            Port: MII

            PHYAD: 0

            Transceiver: internal

            Auto-negotiation: on

            Supports Wake-on: pumbg

            Wake-on: g

            Current message level: 0x00000033 (51)

                                   drv probe ifdown ifup

            Link detected: yes


    und für eth1: 

    Settings for eth1:

            Supported ports: [ TP ]

            Supported link modes:   10baseT/Half 10baseT/Full

                                    100baseT/Half 100baseT/Full

                                    1000baseT/Full

            Supports auto-negotiation: Yes

            Advertised link modes:  10baseT/Half 10baseT/Full

                                    100baseT/Half 100baseT/Full

                                    1000baseT/Full

            Advertised pause frame use: No

            Advertised auto-negotiation: Yes

            Speed: 100Mb/s

            Duplex: Full

            Port: Twisted Pair

            PHYAD: 1

            Transceiver: internal

            Auto-negotiation: on

            MDI-X: Unknown

            Supports Wake-on: umbg

            Wake-on: g

            Current message level: 0x00000007 (7)

                                   drv probe link

            Link detected: yes


    'generic-receive-offload' / GRO ist gar nicht vorhanden. Ist das die Ursache?

    Gruß
    LoD
  • 0 in reply to trollvottel
    Speziell interessant wären die eingestellten werte für "generic-receive-offload"


    Hallo LoD,

    Das kann man sich mit z.B. "ethtool -k eth0" für eth0 anzeigen lassen

    Gruß,
    Matthias
Unfiltered HTML