Hi guys,
I got a major problem with my AP55
first a short environment overview:
Our UTM 220 (v 9.404-5) is direcly connected to the core switch using several vlans in a two NIC LAG. From this core switch we're using LWL Trunks to serve 5 other Gigabit PoE Switches.
at the moment there are 4 AP30 and 2 AP10 in use, withour any problems. I bought a new AP55 for the new building that is also connected over an 4 NIC LWL Trunk.
If I use one of these AP30 on this switch, everything works fine. but the AP55 won't connect.
I've tried to route the strage IP 1.2.3.4 and configured our DHCP server to use the option 234.. without success. The AP55 tries to start.. wait about 10 seconds and going to reboot. here's the console Log:
"
U-Boot 1.1.4-ge258ebab-dirty (Jun 13 2014 - 14:05:53)
7679WSC - Scorpion 1.0DRAM:
sri
Scorpion 1.0
ath_ddr_initial_config(178): (32bit) ddr2 init
tap = 0x00000003
Tap (low, high) = (0x5, 0x1d)
Tap values = (0x11, 0x11, 0x11, 0x11)
128 MB
Flash Manuf Id 0xc2, DeviceId0 0x20, DeviceId1 0x18
Flash [MX25L12845E] sectors: 256
Flash: 16 MB
In: serial
Out: serial
Err: serial
Net: ath_gmac_enet_initialize...
athrs_sgmii_res_cal: cal value = 0x1
Fetching MAC Address from 0x87fed2fc
ath_gmac_enet_initialize: reset mask:c02200
Scorpion ---->8035 PHY*
AR8035 PHY reg init
: cfg1 0x80000000 cfg2 0x7114
eth0: 00:aa:bb:cc:dd:00
AR8035 found!
[0:4]Phy ID 4d:d072
Port 0, Neg Success
eth0 up
eth0
Setting 0x18116290 to 0x458ba14f
Please choose the operation:
1: Load system code to SDRAM via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
1 0
3: System Boot system code via Flash.
## Booting image at 9f070000 ...
Image Name: MIPS OpenWrt Linux-3.18.11
Created: 2015-10-13 13:24:06 UTC
Image Type: MIPS Linux Kernel Image (gzip compressed)
Data Size: 5014979 Bytes = 4.8 MB
Load Address: 80060000
Entry Point: 80060000
Verifying Checksum at 0x9f070040 ...OK
Uncompressing Kernel Image ... OK
Starting kernel ...
[ 0.000000] Linux version 3.18.11 (rpmbuild@axgbuild) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 unknown) ) #3 Tue Oct 13 15:23:44 CEST 2015
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
[ 0.000000] SoC: Qualcomm Atheros QCA9558 ver 1 rev 0
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x07ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x07ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x07ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: board=AP55 console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot),64k(u-boot-env),64k(art),64k(astaro_stat_cfg),7616k(astaro_image),64k(astaro_backup),64k(astaro_dyn_cfg) rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 122728K/131072K available (2342K kernel code, 122K rwdata, 432K rodata, 3688K init, 182K bss, 8344K reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Clocks: CPU:720.000MHz, DDR:600.000MHz, AHB:200.000MHz, Ref:40.000MHz
[ 0.000000] Calibrating delay loop... 358.80 BogoMIPS (lpj=1794048)
[ 0.060000] pid_max: default: 32768 minimum: 301
[ 0.060000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.070000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.070000] NET: Registered protocol family 16
[ 0.080000] MIPS: machine is Sophos AP55
[ 0.080000] registering PCI controller with io_map_base unset
[ 0.090000] ar724x-pci ar724x-pci.1: PCIe link is down
[ 0.090000] registering PCI controller with io_map_base unset
[ 0.320000] PCI host bridge to bus 0000:00
[ 0.330000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x11ffffff]
[ 0.330000] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.340000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.340000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x101fffff 64bit]
[ 0.350000] pci 0000:00:00.0: BAR 6: assigned [mem 0x10200000-0x1020ffff pref]
[ 0.350000] PCI host bridge to bus 0000:01
[ 0.360000] pci_bus 0000:01: root bus resource [mem 0x12000000-0x13ffffff]
[ 0.360000] pci_bus 0000:01: root bus resource [io 0x0001]
[ 0.370000] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
[ 0.370000] pci 0000:00:00.0: using irq 40 for pin 1
[ 0.380000] Switched to clocksource MIPS
[ 0.380000] NET: Registered protocol family 2
[ 0.390000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.390000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.400000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.400000] TCP: reno registered
[ 0.410000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.410000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.420000] NET: Registered protocol family 1
[ 4.330000] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 4.340000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 4.350000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 4.360000] msgmni has been set to 239
[ 4.360000] io scheduler noop registered
[ 4.370000] io scheduler deadline registered (default)
[ 4.370000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 4.380000] console [ttyS0] disabled
þ[ 4.400000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a 16550A
[ 4.410000] console [ttyS0] enabled
[ 4.410000] console [ttyS0] enabled
[ 4.420000] bootconsole [early0] disabled
[ 4.420000] bootconsole [early0] disabled
[ 4.430000] m25p80 spi0.0: found mx25l12805d, expected m25p80
[ 4.430000] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[ 4.440000] 7 cmdlinepart partitions found on MTD device spi0.0
[ 4.440000] Creating 7 MTD partitions on "spi0.0":
[ 4.450000] 0x000000000000-0x000000040000 : "u-boot"
[ 4.460000] 0x000000040000-0x000000050000 : "u-boot-env"
[ 4.460000] 0x000000050000-0x000000060000 : "art"
[ 4.470000] 0x000000060000-0x000000070000 : "astaro_stat_cfg"
[ 4.470000] 0x000000070000-0x0000007e0000 : "astaro_image"
[ 4.480000] 0x0000007e0000-0x0000007f0000 : "astaro_backup"
[ 4.490000] 0x0000007f0000-0x000000800000 : "astaro_dyn_cfg"
[ 4.510000] libphy: ag71xx_mdio: probed
[ 5.180000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:04 [uid=004dd072, driver=Atheros 8035 ethernet]
[ 5.190000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[ 5.190000] TCP: cubic registered
[ 5.200000] NET: Registered protocol family 17
[ 5.200000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 5.210000] 8021q: 802.1Q VLAN Support v1.8
[ 5.230000] Freeing unused kernel memory: 3688K (80336000 - 806d0000)
[ 5.250000] init: failed to symlink /tmp -> /var
[ 5.260000] init: Console is alive
[ 5.260000] init: - watchdog -
[ 6.260000] init: - preinit -
[ 6.410000] random: mktemp urandom read with 10 bits of entropy available
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 9.490000] procd: - early -
[ 9.500000] procd: - watchdog -
[ 10.030000] procd: - ubus -
[ 11.050000] procd: - init -
Please press Enter to activate this console.
[ 12.850000] Loading modules backported from Linux version master-2015-06-03-0-g4318dca
[ 12.860000] Backport generated by backports.git backports-20150525-0-g49969bd
[ 12.880000] cfg80211: Calling CRDA to update world regulatory domain
[ 12.880000] cfg80211: World regulatory domain updated:
[ 12.890000] cfg80211: DFS Master region: unset
[ 12.890000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 12.900000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 12.910000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 12.920000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 12.930000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 12.940000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 12.950000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 12.950000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 12.960000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 13.050000] ieee80211 phy0: Atheros AR9550 Rev:0 mem=0xb8100000, irq=47
[ 13.080000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 13.080000] ath10k_pci 0000:00:00.0: pci irq legacy interrupts 0 irq_mode 0 reset_mode 0
[ 13.150000] cfg80211: Calling CRDA for country: AW
[ 13.150000] cfg80211: Regulatory domain changed to country: AW
[ 13.160000] cfg80211: DFS Master region: ETSI
[ 13.160000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 13.170000] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 13.180000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[ 13.190000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 13.200000] cfg80211: (5490000 KHz - 5710000 KHz @ 160000 KHz), (N/A, 2700 mBm), (0 s)
[ 13.370000] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/cal-pci-0000:00:00.0.bin failed with error -2
[ 13.380000] ath10k_pci 0000:00:00.0: Falling back to user helper
[ 13.450000] firmware ath10k!cal-pci-0000:00:00.0.bin: firmware_loading_store: map pages failed
[ 13.560000] ath10k_pci 0000:00:00.0: otp stream is empty, using board.bin contents
[ 14.590000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, 0x043202ff) fw 10.2.4.70-2 api 5 htt 2.1 wmi 5 cal otp max_sta 128
[ 14.610000] ath10k_pci 0000:00:00.0: debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[ 17.690000] cfg80211: Calling CRDA for country: DE
[ 17.690000] cfg80211: Regulatory domain changed to country: DE
[ 17.700000] cfg80211: DFS Master region: ETSI
[ 17.700000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 17.710000] cfg80211: (2400000 KHz - 2483000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 17.720000] cfg80211: (5150000 KHz - 5250000 KHz @ 80000 KHz, 200000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[ 17.730000] cfg80211: (5250000 KHz - 5350000 KHz @ 80000 KHz, 200000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 17.740000] cfg80211: (5470000 KHz - 5725000 KHz @ 160000 KHz), (N/A, 2700 mBm), (0 s)
[ 17.750000] cfg80211: (57000000 KHz - 66000000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[ 18.510000] device eth0 entered promiscuous mode
[ 58.970000] device eth0 left promiscuous mode
[ 58.980000] br-lan: port 1(eth0) entered disabled state
"
it is not possible to use a static IP or something else. the switch port, the AP is connected to, is always down. I also tried several switches an different port or VLANs...
So that's it..
any ideas?! :D
btw.: this is de second AP55.. the first one has been replaced by Sophos. but the new one shows the same fault.
regards
This thread was automatically locked due to age.
