This discussion has been locked.

You can no longer post new replies to this discussion. If you have a question you can start a new discussion

iView Setup network configuration.

I may be missing something really simple, or misunderstand the intended use of iView 2.0.

I installed this in a Hyper-V server, then according to the guide I needed to go to 172.16.16.18. I thought this must be a mistake so I checked for used IP's in my DHCP range and found none.

Most of my network is in a simple 192.160.0.0/24 segment so I fired up a workstation VM and set a static address to 172.16.16.100. Now I could get to the iView configuration web page.

Then it prompts me for network configuration for WAN port B. I'm not sure what this is, since I thought it would just be using a simple connection to my Sophos UTM 9. I tried putting 192.168.0.0/24 info in the fields but it give me "Incorrect Configuration" when I click "Save Changes".

What am I missing here?

This thread was automatically locked due to age.

Parents

0 sachingurung over 7 years ago

Hi Matt,

Please show me a picture of this page. I guess the IP address your should try here is the WAN interface IP address on the UTM; generally eth1 on UTM.

Thanks

Sachin Gurung
Team Lead | Sophos Technical Support
Knowledge Base | @SophosSupport | Video tutorials
Remember to like a post. If a post (on a question thread) solves your question use the 'This helped me' link.
Cancel
Vote Up 0 Vote Down

Cancel

Reply

0 sachingurung over 7 years ago

Hi Matt,

Please show me a picture of this page. I guess the IP address your should try here is the WAN interface IP address on the UTM; generally eth1 on UTM.

Thanks

Sachin Gurung
Team Lead | Sophos Technical Support
Knowledge Base | @SophosSupport | Video tutorials
Remember to like a post. If a post (on a question thread) solves your question use the 'This helped me' link.
Cancel
Vote Up 0 Vote Down

Cancel

Children

0 Matt Davis over 7 years ago in reply to sachingurung

The WAN interface of my UTM is DHCP.

What I'm trying to leverage iView for, is to generate daily internet usage reports and such. I figured this would just connect to the UTM via the management address and do it's thing once configured.
Cancel
Vote Up 0 Vote Down

Cancel
0 Matt Davis over 7 years ago in reply to Matt Davis

Incorrect Configuration

I get the same message if I enter my UTM's current eth2 (WAN) IP information in.

I only gave this iView server one NIC on my internal network, does it require more?
Cancel
Vote Up 0 Vote Down

Cancel
0 Matt Davis over 7 years ago in reply to Matt Davis

Anyone? Am I just "misusing" this software?
Cancel
Vote Up 0 Vote Down

Cancel
0 OldSchool over 7 years ago in reply to Matt Davis

I just set this up on a stand alone box (with one NIC), I had the same issue with the first install, so I added a second NIC and once it installed, I was able to log in using the first ip 172.16.16.whatever and set the 2nd NIC to the LAN IP I wanted it to be ex. 192.168.4.12 then I was able to see it on my LAN, and use it.

HTH

KCI
Cancel
Vote Up 0 Vote Down

Cancel
0 DouglasFoster over 7 years ago in reply to Matt Davis

I found tbis very confusing and frustrating as well. This is much eaer to do from the console window. Ihad to ask support for the password - I thonk it is admin. The console window has a simple menu. Which makes sense. Tbe web page wizard assumes that you have multiple nics - I think 4. Wnen I thought it was repeating a question it qas actually asking about the next nic. At any rate, from the console I configured exactly what I wanted.

Xg setup was similar.
Cancel
Vote Up 0 Vote Down

Cancel