This discussion has been locked.

You can no longer post new replies to this discussion. If you have a question you can start a new discussion

Installing SUM on VM

Hello

I am currently trying to install a SUM (newly downloaded, new version) in a kvm environment.
But already at the start, I run into troubles.

The installation cant detect my storage and I cant see anyway to provide at driver.

I have tried to install UTM9. It worked right out of the box, with no special requirements.

Anyone have some experience in this?

This thread was automatically locked due to age.

Parents

0 rfcat_vk over 7 years ago

I haven't checked, but believe there is a KVM version of the ISO?

When I built my SUM on the VM I used the standard ISO.

Amended incorrect information. Changed UTM to SUM.

Both are correct.

XG115W - v20.0.2 MR-2 - Home

XG on VM 8 - v21 GA

If a post solves your question please use the 'Verify Answer' button.
Cancel
Vote Up 0 Vote Down

Cancel
0 Karsten over 7 years ago in reply to rfcat_vk

The VM version of the SUM-image are discontinued.
Cancel
Vote Up 0 Vote Down

Cancel
0 BAlfson over 7 years ago in reply to Karsten

The VM ISOs were all discontinued - just use the regular ISO. Can you see where the installation is hanging - on which driver?

Cheers - Bob

Sophos UTM Community Moderator
Sophos Certified Architect - UTM
Sophos Certified Engineer - XG
Gold Solution Partner since 2005

MediaSoft, Inc. USA
Cancel
Vote Up 0 Vote Down

Cancel
0 Karsten over 7 years ago in reply to BAlfson

Detecting storage devices
Detecting storage devices
Storage controller: Qumranet Qemu virtual machine
Driver: ata_pixx,ata_generic,pata_acpi
Storage controller: Qumranet SCSI storage controller
Drivers: virtio_pci
Detecting disks
Kernel: [662.648351] BIOS EDD facility v0.16 2004-jun-25, 1 devices found
No disk found, retrying after some time (2)
No disk found, retrying after some time (1)
No disk found, retrying after some time (0)
Cancel
Vote Up 0 Vote Down

Cancel
0 rfcat_vk over 7 years ago in reply to Karsten

How is the scsi controller setup, if a raid array the install will not see the disks?

XG115W - v20.0.2 MR-2 - Home

XG on VM 8 - v21 GA

If a post solves your question please use the 'Verify Answer' button.
Cancel
Vote Up 0 Vote Down

Cancel
0 BAlfson over 7 years ago in reply to Karsten

If you're using the same underlying Linux definition as you have with the UTM VM, this is beyond my knowledge of KVM.

Cheers - Bob

Sophos UTM Community Moderator
Sophos Certified Architect - UTM
Sophos Certified Engineer - XG
Gold Solution Partner since 2005

MediaSoft, Inc. USA
Cancel
Vote Up 0 Vote Down

Cancel
0 Karsten over 7 years ago in reply to BAlfson

I can mount the UTM iso at the exact same VM and install it with out any extra effort.
Cancel
Vote Up 0 Vote Down

Cancel
0 Karsten over 7 years ago in reply to rfcat_vk

rfcat_vk said:

How is the scsi controller setup, if a raid array the install will not see the disks?

No raid setup
Cancel
Vote Up 0 Vote Down

Cancel

Reply

0 Karsten over 7 years ago in reply to rfcat_vk

rfcat_vk said:

How is the scsi controller setup, if a raid array the install will not see the disks?

No raid setup
Cancel
Vote Up 0 Vote Down

Cancel

Children

No Data