This discussion has been locked.

You can no longer post new replies to this discussion. If you have a question you can start a new discussion

Setting up Wifi on a RED 15w connected to a SG-105w

How am I suppodes to setup/enable the WiFi on a RED 15w connected to a SG-105w? The W-Lan on this remote UTM is already up and working.

In the Admin interface, I can see the interface wlan0 (which is enabled, working and bridged to eth0); as well as a wlan1 which I think it's the interface provided by the RED (not fully sure though).

I have created a new SSID too, pointing to wlan1, but no matter what I try there are no Wireless networks in the vicinity of the device I used to check.

Any help is appreciated!

This thread was automatically locked due to age.

0 BAlfson over 8 years ago

Hi, Adrian, and welcome to the UTM Community!

What do you see in the RED and Wireless Protection logs when you power on the RED?

Cheers - Bob

Sophos UTM Community Moderator
Sophos Certified Architect - UTM
Sophos Certified Engineer - XG
Gold Solution Partner since 2005

MediaSoft, Inc. USA
Cancel
Vote Up 0 Vote Down

Cancel
0 AdrianFöder over 8 years ago in reply to BAlfson

Hi Bob,

what logs exactly do you mean?

Maybe the following helps; when I'm on the dashboard, the link is as follows:

(wlan1 is the one in question).

I guess I would have to define an Access Point?

There are no pending ones,

Clicking on this Edit button above gives me

but even when I try to add this one I don't see any Wifi around when checking with devices...
Cancel
Vote Up 0 Vote Down

Cancel
0 sachingurung over 8 years ago in reply to AdrianFöder

Hi Adrian,

Please refer: https://www.sophos.com/en-us/support/knowledgebase/122080.aspx

Hope that helps.

Sachin Gurung
Team Lead | Sophos Technical Support
Knowledge Base | @SophosSupport | Video tutorials
Remember to like a post. If a post (on a question thread) solves your question use the 'This helped me' link.
Cancel
Vote Up 0 Vote Down

Cancel
0 AdrianFöder over 8 years ago in reply to sachingurung

Hi,

I followed this article already for the WIFI of the 105w which works fine; but now I am stuck how to configure the wifi of the RED.
Cancel
Vote Up 0 Vote Down

Cancel
0 AdrianFöder over 8 years ago in reply to AdrianFöder

Hi guys, any news on this? I'd like the wifi on the RED a dedicated one which ideally only serves the Internet but does not allow access to any internal device.

But as said: the LINK says down, and I can't see any Access Point (which I should?)
Cancel
Vote Up 0 Vote Down

Cancel
0 BAlfson over 8 years ago in reply to AdrianFöder

You're right that you can't see the RED wireless until the link is up. Insert pictures of your RED and Interface definitions open in Edit.

Cheers - Bob

Sophos UTM Community Moderator
Sophos Certified Architect - UTM
Sophos Certified Engineer - XG
Gold Solution Partner since 2005

MediaSoft, Inc. USA
Cancel
Vote Up 0 Vote Down

Cancel
0 AdrianFöder over 8 years ago in reply to BAlfson

Bridged Internal and WLAN (0) on main site and the RED on the remote location.
Cancel
Vote Up 0 Vote Down

Cancel
0 BAlfson over 8 years ago in reply to AdrianFöder

I meant the RED 15 definition in the RED section.

Cheers - Bob

Sophos UTM Community Moderator
Sophos Certified Architect - UTM
Sophos Certified Engineer - XG
Gold Solution Partner since 2005

MediaSoft, Inc. USA
Cancel
Vote Up 0 Vote Down

Cancel
0 AdrianFöder over 8 years ago in reply to BAlfson

This one?

Thanks for your help!
Cancel
Vote Up 0 Vote Down

Cancel
0 BAlfson over 8 years ago in reply to AdrianFöder

That all looks good, does #1 in Rulz give you any indications? I wonder if you're missing a masq rule 'Hummelbuehl 9 (Network) -> External (WAN)' and maybe a firewall rule.

Cheers - Bob

Sophos UTM Community Moderator
Sophos Certified Architect - UTM
Sophos Certified Engineer - XG
Gold Solution Partner since 2005

MediaSoft, Inc. USA
Cancel
Vote Up 0 Vote Down

Cancel