Hello everyone,
I would like to know how I can flash/recover a RED 50.
I found a post about a recovery tool for Reds/ APs but it's only for the Red 10 rev.2/3 and the software couldn't find my Red.
Link: https://community.sophos.com/kb/en-us/118843
So I hope someone can help me
Thanks
Niko
Hallo Niko and welcome to the UTM Community!
Others have reported here recently that Up2Dating to 9.601/2 seemed to break their RED. The first thing to try is to remove and replace the RED in WebAdmin. Don't forget to write down the unlock code before deleting! Any luck with that?
Cheers - Bob
Hi Bob,
thanks for your answer but my Buddy has already reported the red, so it's not nessasary anymore.
But thanks a lot !
Niko
Dear Bob
I have the same Problem. Is there a solution to flash the RED 50 V1 with the newest Firmware and then
provisioning the RED with the UTM (like USB Stick).
Regards and thank for your Input.
Phil
Hallo Philipp and welcome to theUTM Community!
In March, Martin (twister5800) said the following solved his problem with RED devices. As root at the command line:
cc set red use_unified_firmware 0
Any luck with that? If not, and you're on 9.601, try Up2Dating to 9.602 as Martin said that also resolved the issue. If all else fails, get a case started with Sophos Support.
Cheers - Bob
We had a RED50 Rev1 that 'bricked' with the 9.601 update. There was nothing we could do to re-flash the firmware. We created a USB stick according to the listed procedure but the RED50 would not even access the USB stick from either USB port on the device. The indicator light on the USB stick never even illuminated.
The unified firmware bug will brick a RED50 completely. Useless POS after that. Get an RMA and have it replaced. Then follow the advice on the other thread and make sure to not use the unified firmware by setting CC SET RED USE_UNIFIED_FIRMWARE flag =0 from the command line of your UTM. Note that the flag is not persistent for future updates and the RED(s) will need to be disabled before a further update, then the flag needs to be set =0 again then re-enable the RED(s).
Hi ignitor,
According to this post by BAlfson from the thread referenced above, yes, that is correct:
BAlfson said:I just got this from Sophos Support:
1. Are any other REDs in danger of being bricked, or is it just the RED 50?
- So far we have only seen RED 50 but this doesn't rule out RED 15
2. In High Availability, does use_unified_firmware need to be set to 0 on all nodes?
- No it would replicate the command
3. Instead of physically unplugging REDs, would it suffice to disable the RED server objects in WebAdmin before applying the Up2Date and then enable them after 9.604 has had use_unified_firmware set to 0?
- In theory yes if you disable the service in the UTM or turn off the RED devices, then they won't be able to get the Firmware Update, so they won't be able to contact the server, and once you re-enable the services they will not search for a new firmware updateCheers - Bob
Garth
Hi all,
in ref to my thread: https://community.sophos.com/products/utm-firewall/f/remote-ethernet-device-red/121385/is-there-really-no-way-to-restore-a-bricked-red-50/441251#441251
Can somebody confirm that the Red50 is PowerPC based !?
Thx & best.
i will keep the topic still open.
We have two RED 50 rev1 here and they stuck while booting.
I have added them more than 5 times again, but they will never get in touch with the UTM again. (no Log entry)
Due that the Flash Tool does not support REV 1 i've inspected the console and there are a lot of commands. Also it is possible to boot a new image.
But from where i can get this file?
Due the research i did not find a way to extract the image from a running RED 59 Rev1.
Does anyone have an idea?
Below a console output
MB351Z => print
baudrate=115200
bootcmd=setenv bootargs root=/dev/mtdblock10 console=ttyS0,115200; nand read 0xc00000 0x5100000 0x100000; nand read 0x1000000 0x5200000 0x1000000; bootm 0x1000000 - 0xc00000;
bootcmd_dram_test=ram_test
bootcmd_nandflash_test=nand_test 0 0x500000
bootcmd_norflash_test=flash_test 0xefe06000 0xefe4ffff
bootcmd_rtctest=rtc_test 20
bootdelay=3
bootloader_flash_update=protect off 0xeff00000 0xeff7ffff; erase 0xeff00000 0xeff7ffff; cp.b 0x100000 0xeff00000 0x80000; protect on 0xeff00000 0xeff7ffff; cmp.b 0x100000 0xeff00000 0x80000
consoledev=ttyS0
eth1addr=00:1A:8C:34:56:6E
eth2addr=00:1A:8C:34:56:6F
ethact=eTSEC1
ethaddr=00:1A:8C:34:56:6D
fdtaddr=c00000
fdtfile=mb351z.dtb
fdtkernel=uImage
filesize=360000
hwconfig=esdhc
lannerboot=setenv bootargs root=/dev/ram rw ramdisk_size=$ramdisksize rootdelay=10 console=ttyS0,115200;usb start;fatload usb 0 $loadaddr $fdtkernel;fatload usb 0 $ramdiskaddr $ramdiskfile;fatload usb 0 $fdtaddr $fdtfile;bootm $loadaddr $ramdiskaddr $fdtaddr;
loadaddr=1000000
loads_echo=1
netdev=eth0
ramdiskaddr=2000000
ramdiskfile=rootfs.ext2.gz.uboot
ramdisksize=2000000
usb_phy_type=ulpi
usbext2boot=setenv bootargs root=/dev/ram rw console=$consoledev,$baudrate; usb start;ext2load usb 0 $loadaddr $fdtkernel;ext2load usb 0 $fdtaddr $fdtfile;ext2load usb 0 $ramdiskaddr $ramdiskfile;bootm $loadaddr $ramdiskaddr $fdtaddr
usbfatboot=setenv bootargs root=/dev/ram rw ramdisk_size=$ramdisksize console=$consoledev,$baudrate; usb start;fatload usb 0 $loadaddr $fdtkernel;fatload usb 0 $fdtaddr $fdtfile;fatload usb 0 $ramdiskaddr $ramdiskfile;bootm $loadaddr $ramdiskaddr $fdtaddr
Environment size: 1680/65531 bytes
Here is the console output:
U-Boot 2010.12 (Jun 13 2012 - 18:57:31)
CPU0: P1020E, Version: 1.1, (0x80ec0011)
Core: E500, Version: 5.1, (0x80212051)
Clock Configuration:
CPU0:533.333 MHz, CPU1:533.333 MHz,
CCB:266.667 MHz,
DDR:333.333 MHz (666.667 MT/s data rate) (Asynchronous), LBC:16.667 MHz
L1: D-cache 32 kB enabled
I-cache 32 kB enabled
Board: P1020RDB Rev
MB-351Z Ver.T03 2012-06-13
I2C: ready
DRAM: Configuring DDR for 666.667 MT/s data rate
DDR: 512 MiB (DDR3, 32-bit, CL=6, ECC off)
FLASH: 2 MiB
L2: 256 KB enabled
NAND: 256 MiB
EEPROM: NXID v0
eTSEC2 is in sgmii mode.
PCIE2: connected to Slot 1 as Root Complex (base addr ffe09000)
PCIE2: Bus 00 - 00
PCIE1: connected to Slot 2 as Root Complex (base addr ffe0a000)
PCIE1: Bus 01 - 01
In: serial
Out: serial
Err: serial
Net: eTSEC1: No support for PHY id ffffffff; assuming generic
eTSEC3: No support for PHY id ffffffff; assuming generic
Init switch to forwarding mode... Done
eTSEC1, eTSEC2, eTSEC3
Hit any key to stop autoboot: 0
NAND read: device 0 offset 0x5100000, size 0x100000
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
1048576 bytes read: OK
NAND read: device 0 offset 0x5200000, size 0x1000000
16777216 bytes read: OK
## Booting kernel from Legacy Image at 01000000 ...
Image Name: Linux-3.18.43
Created: 2019-04-08 12:46:24 UTC
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 2408259 Bytes = 2.3 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 00c00000
Booting using the fdt blob at 0xc00000
Uncompressing Kernel Image ... OK
Loading Device Tree to 00ffa000, end 00fffb18 ... OK
[ 0.000000] Using P1020 RDB machine description
[ 0.000000] Memory CAM mapping: 256/256 Mb, residual: 0Mb
[ 0.000000] Linux version 3.18.43 (jenkins@kar-nsgci-node-21) (gcc version 5.4.0 (LEDE GCC 5.4.0 1-373-b15c4b2a-e9f0c31) ) #0 SMP Mon Apr 8 12:46:24 2019
[ 0.000000] CPU maps initialized for 1 thread per core
[ 0.000000] bootconsole [udbg0] enabled
setup_arch: bootmem
mpc85xx_rdb_setup_arch()
[ 0.000000] MPC85xx RDB board from Freescale Semiconductor
arch: exit
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00000000-0x1fffffff]
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x1fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x1fffffff]
[ 0.000000] MMU: Allocated 1088 bytes of context maps for 255 contexts
[ 0.000000] PERCPU: Embedded 9 pages/cpu @c090e000 s6144 r8192 d22528 u36864
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
[ 0.000000] Kernel command line: root=/dev/mtdblock10 console=ttyS0,115200
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Sorting __ex_table...
[ 0.000000] Memory: 448588K/524288K available (3600K kernel code, 204K rwdata, 948K rodata, 180K init, 213K bss, 75700K reserved)
[ 0.000000] Kernel virtual memory layout:
[ 0.000000] * 0xfffdf000..0xfffff000 : fixmap
[ 0.000000] * 0xfdffd000..0xfe000000 : early ioremap
[ 0.000000] * 0xe1000000..0xfdffd000 : vmalloc & ioremap
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:512 nr_irqs:512 16
[ 0.000000] mpic: Setting up MPIC " OpenPIC " version 1.2 at ffe40000, max 2 CPUs
[ 0.000000] mpic: ISU size: 256, shift: 8, mask: ff
[ 0.000000] mpic: Initializing for 256 sources
[ 0.000014] clocksource: timebase mult[1e000005] shift[24] registered
[ 0.006702] pid_max: default: 32768 minimum: 301
[ 0.011457] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.018014] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.025835] mpic: requesting IPIs...
[ 0.032176] Brought up 2 CPUs
[ 0.040413] NET: Registered protocol family 16
[ 0.054175] Found FSL PCI host bridge at 0x00000000ffe09000. Firmware bus number: 0->0
[ 0.062052] PCI host bridge /pcie@ffe09000 (primary) ranges:
[ 0.067699] MEM 0x00000000a0000000..0x00000000bfffffff -> 0x00000000a0000000
[ 0.074914] IO 0x00000000ffc30000..0x00000000ffc3ffff -> 0x0000000000000000
[ 0.082063] /pcie@ffe09000: PCICSRBAR @ 0xfff00000
[ 0.087274] Found FSL PCI host bridge at 0x00000000ffe0a000. Firmware bus number: 0->0
[ 0.095142] PCI host bridge /pcie@ffe0a000 ranges:
[ 0.100011] MEM 0x00000000c0000000..0x00000000dfffffff -> 0x00000000c0000000
[ 0.107227] IO 0x00000000ffc20000..0x00000000ffc2ffff -> 0x0000000000000000
[ 0.114375] /pcie@ffe0a000: PCICSRBAR @ 0xfff00000
[ 0.134501] PCI: Probing PCI hardware
[ 0.138340] fsl-pci ffe09000.pcie: PCI host bridge to bus 0000:00
[ 0.144389] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 0.150549] pci_bus 0000:00: root bus resource [mem 0xa0000000-0xbfffffff]
[ 0.157424] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.163417] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.171548] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 0.177096] fsl-pci ffe0a000.pcie: PCI host bridge to bus 0001:02
[ 0.183147] pci_bus 0001:02: root bus resource [io 0x20000-0x2ffff] (bus address [0x0000-0xffff])
[ 0.192089] pci_bus 0001:02: root bus resource [mem 0xc0000000-0xdfffffff]
[ 0.198963] pci_bus 0001:02: root bus resource [bus 02-ff]
[ 0.204908] pci 0001:02:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.213044] pci 0001:02:00.0: PCI bridge to [bus 03-ff]
[ 0.218371] PCI: Cannot allocate resource region 0 of PCI bridge 1, will remap
[ 0.225543] PCI: Cannot allocate resource region 0 of device 0000:00:00.0, will remap
[ 0.233362] PCI: Cannot allocate resource region 0 of device 0001:02:00.0, will remap
[ 0.241240] pci 0000:00:00.0: BAR 0: no space for [mem size 0x00100000]
[ 0.247807] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x00100000]
[ 0.254765] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 0.259725] pci 0000:00:00.0: bridge window [mem 0xa0000000-0xbfffffff]
[ 0.266510] pci_bus 0000:00: Some PCI device resources are unassigned, try booting with pci=realloc
[ 0.275619] pci 0001:02:00.0: BAR 0: no space for [mem size 0x00100000]
[ 0.282172] pci 0001:02:00.0: BAR 0: failed to assign [mem size 0x00100000]
[ 0.289129] pci 0001:02:00.0: PCI bridge to [bus 03]
[ 0.294089] pci 0001:02:00.0: bridge window [io 0x20000-0x2ffff]
[ 0.300354] pci 0001:02:00.0: bridge window [mem 0xc0000000-0xdfffffff]
[ 0.307138] pci_bus 0001:02: Some PCI device resources are unassigned, try booting with pci=realloc
[ 0.334286] usbcore: registered new interface driver usbfs
[ 0.339826] usbcore: registered new interface driver hub
[ 0.345173] usbcore: registered new device driver usb
[ 0.350231] pps_core: LinuxPPS API ver. 1 registered
[ 0.355130] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.364308] PTP clock support registered
[ 0.369235] Switched to clocksource timebase
[ 0.374812] NET: Registered protocol family 2
[ 0.379939] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.386995] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.393465] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.399846] TCP: reno registered
[ 0.403014] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.408853] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.415372] NET: Registered protocol family 1
[ 0.420041] RPC: Registered named UNIX socket transport module.
[ 0.425946] RPC: Registered udp transport module.
[ 0.430608] RPC: Registered tcp transport module.
[ 0.435303] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.444106] futex hash table entries: 512 (order: 2, 16384 bytes)
[ 0.451231] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.457569] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.467698] msgmni has been set to 1004
[ 0.473729] io scheduler noop registered
[ 0.477617] io scheduler deadline registered (default)
[ 0.482990] pcieport 0001:02:00.0: enabling device (0106 -> 0107)
[ 0.532402] Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
[ 0.539880] console [ttyS0] disabled
[ 0.543472] serial8250.0: ttyS0 at MMIO 0xffe04500 (irq = 42, base_baud = 16666666) is a 16550A
[ 0.552152] console [ttyS0] enabled
[ 0.552152] console [ttyS0] enabled
[ 0.559082] bootconsole [udbg0] disabled
[ 0.559082] bootconsole [udbg0] disabled
[ 0.567682] serial8250.0: ttyS1 at MMIO 0xffe04600 (irq = 42, base_baud = 16666666) is a 16550A
[ 0.577481] console [ttyS0] disabled
[ 0.581127] console [ttyS0] enabled
[ 0.585547] ffe04600.serial: ttyS1 at MMIO 0xffe04600 (irq = 42, base_baud = 16666666) is a 16550
[ 0.594996] Generic RTC Driver v1.07
[ 0.600012] efe00000.nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x002249
[ 0.610075] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.615292] Amd/Fujitsu Extended Query version 1.3.
[ 0.620368] number of CFI chips: 1
[ 0.624341] 5 ofpart partitions found on MTD device efe00000.nor
[ 0.630392] Creating 5 MTD partitions on "efe00000.nor":
[ 0.635747] 0x000000000000-0x0000000e0000 : "NOR reserved"
[ 0.642180] 0x0000000e0000-0x0000000f0000 : "NOR env flash2"
[ 0.648695] 0x0000000f0000-0x000000100000 : "NOR env flash"
[ 0.655132] 0x000000100000-0x000000180000 : "NOR Normal mode"
[ 0.661792] 0x000000180000-0x000000200000 : "NOR Backup mode"
[ 0.669405] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[ 0.675909] nand: Micron MT29F2G08ABAEAWP
[ 0.679950] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[ 0.685645] nand: WARNING: ffa00000.flash: the ECC used on your system is too weak compared to the one required by the NAND chip
[ 0.698114] Bad block table found at page 131008, version 0x01
[ 0.705566] Bad block table found at page 130944, version 0x01
[ 0.712892] 7 ofpart partitions found on MTD device ffa00000.flash
[ 0.719119] Creating 7 MTD partitions on "ffa00000.flash":
[ 0.724648] 0x000000000000-0x000000100000 : "fdt1"
[ 0.730392] 0x000000100000-0x000001100000 : "uimage1"
[ 0.736327] 0x000001100000-0x000005100000 : "rootfs1"
[ 0.742306] 0x000005100000-0x000005200000 : "fdt2"
[ 0.747941] 0x000005200000-0x000006200000 : "uimage2"
[ 0.753897] 0x000006200000-0x00000a200000 : "rootfs2"
[ 0.759883] 0x00000a200000-0x000010000000 : "data"
[ 0.765705] eLBC NAND device at 0xffa00000, bank 1
[ 0.774739] libphy: Fixed MDIO Bus: probed
[ 0.780507] libphy: Freescale PowerQUICC MII Bus: probed
[ 0.786111] Create Marvell Switch PHY device 0x10 manually
[ 0.793006] libphy: Freescale PowerQUICC MII Bus: probed
[ 0.799806] fsl-gianfar soc@ffe00000:ethernet@B0000: enabled errata workarounds, flags: 0x4
[ 0.819092] fsl-gianfar soc@ffe00000:ethernet@B0000 eth0: mac: 00:1a:8c:34:56:6d
[ 0.826550] fsl-gianfar soc@ffe00000:ethernet@B0000 eth0: Running with NAPI enabled
[ 0.834247] fsl-gianfar soc@ffe00000:ethernet@B0000 eth0: RX BD ring size for Q[0]: 256
[ 0.842286] fsl-gianfar soc@ffe00000:ethernet@B0000 eth0: RX BD ring size for Q[1]: 256
[ 0.850322] fsl-gianfar soc@ffe00000:ethernet@B0000 eth0: TX BD ring size for Q[0]: 256
[ 0.858359] fsl-gianfar soc@ffe00000:ethernet@B0000 eth0: TX BD ring size for Q[1]: 256
[ 0.866683] fsl-gianfar soc@ffe00000:ethernet@B1000: enabled errata workarounds, flags: 0x4
[ 0.885947] fsl-gianfar soc@ffe00000:ethernet@B1000 eth1: mac: 00:1a:8c:34:56:6e
[ 0.893399] fsl-gianfar soc@ffe00000:ethernet@B1000 eth1: Running with NAPI enabled
[ 0.901087] fsl-gianfar soc@ffe00000:ethernet@B1000 eth1: RX BD ring size for Q[0]: 256
[ 0.909124] fsl-gianfar soc@ffe00000:ethernet@B1000 eth1: RX BD ring size for Q[1]: 256
[ 0.917160] fsl-gianfar soc@ffe00000:ethernet@B1000 eth1: TX BD ring size for Q[0]: 256
[ 0.925197] fsl-gianfar soc@ffe00000:ethernet@B1000 eth1: TX BD ring size for Q[1]: 256
[ 0.934032] fsl-gianfar soc@ffe00000:ethernet@B2000: enabled errata workarounds, flags: 0x4
[ 0.953335] fsl-gianfar soc@ffe00000:ethernet@B2000 eth2: mac: 00:1a:8c:34:56:6f
[ 0.960773] fsl-gianfar soc@ffe00000:ethernet@B2000 eth2: Running with NAPI enabled
[ 0.968471] fsl-gianfar soc@ffe00000:ethernet@B2000 eth2: RX BD ring size for Q[0]: 256
[ 0.976510] fsl-gianfar soc@ffe00000:ethernet@B2000 eth2: RX BD ring size for Q[1]: 256
[ 0.984547] fsl-gianfar soc@ffe00000:ethernet@B2000 eth2: TX BD ring size for Q[0]: 256
[ 0.992593] fsl-gianfar soc@ffe00000:ethernet@B2000 eth2: TX BD ring size for Q[1]: 256
[ 1.001017] usbcore: registered new interface driver cdc_eem
[ 1.006857] usbcore: registered new interface driver cdc_ncm
[ 1.012634] usbcore: registered new interface driver huawei_cdc_ncm
[ 1.019026] usbcore: registered new interface driver qmi_wwan
[ 1.024885] usbcore: registered new interface driver cdc_mbim
[ 1.030675] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.037364] ehci-pci: EHCI PCI platform driver
[ 1.041933] ehci-platform: EHCI generic platform driver
[ 1.047402] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.053843] ohci-pci: OHCI PCI platform driver
[ 1.058413] ohci-platform: OHCI generic platform driver
[ 1.063944] /soc@ffe00000/usb@22000: Invalid 'dr_mode' property, fallback to host mode
[ 1.072092] fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
[ 1.078778] fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
[ 1.086160] fsl-ehci fsl-ehci.0: irq 28, io mem 0xffe22000
[ 1.101267] fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
[ 1.107728] hub 1-0:1.0: USB hub found
[ 1.111566] hub 1-0:1.0: 1 port detected
[ 1.116071] usbcore: registered new interface driver cdc_acm
[ 1.121780] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 1.129911] usbcore: registered new interface driver cdc_wdm
[ 1.135615] booke_wdt: powerpc book-e watchdog driver loaded
[ 1.142518] talitos ffe30000.crypto: hwrng
[ 1.148282] talitos ffe30000.crypto: md5-talitos alg registration failed
[ 1.155038] talitos ffe30000.crypto: sha1-talitos alg registration failed
[ 1.161859] talitos ffe30000.crypto: sha224-talitos alg registration failed
[ 1.168850] talitos ffe30000.crypto: sha256-talitos alg registration failed
[ 1.175842] talitos ffe30000.crypto: sha384-talitos alg registration failed
[ 1.182833] talitos ffe30000.crypto: sha512-talitos alg registration failed
[ 1.189825] talitos ffe30000.crypto: hmac-md5-talitos alg registration failed
[ 1.196990] talitos ffe30000.crypto: hmac-sha1-talitos alg registration failed
[ 1.204250] talitos ffe30000.crypto: hmac-sha224-talitos alg registration failed
[ 1.211677] talitos ffe30000.crypto: hmac-sha256-talitos alg registration failed
[ 1.219114] talitos ffe30000.crypto: hmac-sha384-talitos alg registration failed
[ 1.226543] talitos ffe30000.crypto: hmac-sha512-talitos alg registration failed
[ 1.233977] talitos ffe30000.crypto: fsl,sec3.3 algorithms registered in /proc/crypto
[ 1.242248] TCP: cubic registered
[ 1.245612] NET: Registered protocol family 17
[ 1.250168] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 1.262834] 8021q: 802.1Q VLAN Support v1.8
[ 1.275069] VFS: Mounted root (squashfs filesystem) readonly on device 31:10.
[ 1.282756] Freeing unused kernel memory: 180K (c0473000 - c04a0000)
[ 1.429254] usb 1-1: new high-speed USB device number 2 using fsl-ehci
[ 1.567731] hub 1-1:1.0: USB hub found
[ 1.571873] hub 1-1:1.0: 2 ports detected
[ 1.962750] init: Console is alive
[ 1.966416] init: - watchdog -
[ 2.521562] blk_update_request: I/O error, dev mtdblock10, sector 3628
[ 2.528160] blk_update_request: I/O error, dev mtdblock10, sector 3630
[ 2.529252] SQUASHFS error: squashfs_read_data failed to read block 0x1c1552
[ 2.529259] SQUASHFS error: Unable to read fragment cache entry [1c1552]
[ 2.529264] SQUASHFS error: Unable to read page, block 1c1552, size 117b8
[ 2.529281] SQUASHFS error: Unable to read fragment cache entry [1c1552]
[ 2.529285] SQUASHFS error: Unable to read page, block 1c1552, size 117b8
[ 2.529298] SQUASHFS error: Unable to read fragment cache entry [1c1552]
[ 2.529302] SQUASHFS error: Unable to read page, block 1c1552, size 117b8
[ 2.529313] SQUASHFS error: Unable to read fragment cache entry [1c1552]
[ 2.529317] SQUASHFS error: Unable to read page, block 1c1552, size 117b8
[ 2.529330] SQUASHFS error: Unable to read fragment cache entry [1c1552]
[ 2.529334] SQUASHFS error: Unable to read page, block 1c1552, size 117b8
[ 2.529346] SQUASHFS error: Unable to read fragment cache entry [1c1552]
[ 2.529350] SQUASHFS error: Unable to read page, block 1c1552, size 117b8
[ 2.529362] SQUASHFS error: Unable to read fragment cache entry [1c1552]
[ 2.529366] SQUASHFS error: Unable to read page, block 1c1552, size 117b8
[ 2.529378] SQUASHFS error: Unable to read fragment cache entry [1c1552]
[ 2.529382] SQUASHFS error: Unable to read page, block 1c1552, size 117b8
[ 2.529395] SQUASHFS error: Unable to read fragment cache entry [1c1552]
[ 2.529399] SQUASHFS error: Unable to read page, block 1c1552, size 117b8
[ 2.529413] SQUASHFS error: Unable to read fragment cache entry [1c1552]
[ 2.529416] SQUASHFS error: Unable to read page, block 1c1552, size 117b8
[ 2.529438] SQUASHFS error: Unable to read fragment cache entry [1c1552]
[ 2.529442] SQUASHFS error: Unable to read page, block 1c1552, size 117b8
[ 2.529455] SQUASHFS error: Unable to read fragment cache entry [1c1552]
[ 2.529459] SQUASHFS error: Unable to read page, block 1c1552, size 117b8
[ 2.529473] SQUASHFS error: Unable to read fragment cache entry [1c1552]
[ 2.529477] SQUASHFS error: Unable to read page, block 1c1552, size 117b8
[ 2.529491] SQUASHFS error: Unable to read fragment cache entry [1c1552]
[ 2.529495] SQUASHFS error: Unable to read page, block 1c1552, size 117b8
[ 2.529511] SQUASHFS error: Unable to read fragment cache entry [1c1552]
[ 2.529515] SQUASHFS error: Unable to read page, block 1c1552, size 117b8
[ 2.754794] init: - preinit -
Mounting ramdisk
Using /dev/mtdblock11 as data partition
Using /dev/mtdblock0 as self partition
[ 4.434616] jffs2: notice: (975) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 4.736198] random: jshn urandom read with 125 bits of entropy available
[ 4.931335] random: nonblocking pool is initialized
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 6.881277] fsl-gianfar soc@ffe00000:ethernet@B0000 eth0: Link is Up - 1Gbps/Full - flow control off
2[ 8.070916] mount_root: mounting /dev/root
[ 8.078142] mount_root: loading kmods from internal overlay
[ 8.103765] blk_update_request: I/O error, dev mtdblock10, sector 3628
[ 8.110367] blk_update_request: I/O error, dev mtdblock10, sector 3630
[ 8.113260] SQUASHFS error: squashfs_read_data failed to read block 0x1c1552
[ 8.113268] SQUASHFS error: Unable to read fragment cache entry [1c1552]
[ 8.113273] SQUASHFS error: Unable to read page, block 1c1552, size 117b8
Bus er[ 8.138038] mount_root: failed to launch kmodloader from internal overlay
ror
[ 8.719284] block: attempting to load /etc/config/fstab
[ 8.754452] block: extroot: not configured
[ 8.760618] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 8.848091] procd: - early -
[ 8.851150] procd: - watchdog -
Failed to connect to ubus
[ 9.613314] procd: - watchdog -
[ 9.616714] procd: - ubus -
[ 9.678994] procd: - init -
Please press Enter to activate this console.
[ 9.892663] blk_update_request: I/O error, dev mtdblock10, sector 3628
[ 9.899299] blk_update_request: I/O error, dev mtdblock10, sector 3630
[ 9.905967] SQUASHFS error: squashfs_read_data failed to read block 0x1c1552
[ 9.913088] SQUASHFS error: Unable to read fragment cache entry [1c1552]
[ 9.919891] SQUASHFS error: Unable to read page, block 1c1552, size 117b8
[ 11.975299] fsl-gianfar soc@ffe00000:ethernet@B1000 new_eth2: renamed from eth1
[ 12.001101] fsl-gianfar soc@ffe00000:ethernet@B2000 eth1: renamed from eth2
[ 12.020842] fsl-gianfar soc@ffe00000:ethernet@B1000 eth2: renamed from new_eth2
[ 15.629314] fsl-gianfar soc@ffe00000:ethernet@B0000 eth0: Link is Up - 1Gbps/Full - flow control off
[ 15.649337] fsl-gianfar soc@ffe00000:ethernet@B2000 eth1: Link is Up - 1Gbps/Full - flow control off
[ 15.713891] fsl-gianfar soc@ffe00000:ethernet@B1000 eth2: Link is Down
[ 31.480236] reboot: Restarting system
[ 9.913088] SQUASHFS error: Unable to read fragment cache entry [1c1552]
[ 9.919891] SQUASHFS error: Unable to read page, block 1c1552, size 117b8
Sadly it looks like you have a corrupt image/drive.
We have had these devices for some time and have never had any issues. This week after applying the latest update we had two location(s) devices that are seemingly bricked.
RED 50v1 Output
U-Boot 2010.12 (Jun 13 2012 - 18:57:31)
CPU0: P1020E, Version: 1.1, (0x80ec0011)
Core: E500, Version: 5.1, (0x80212051)
Clock Configuration:
CPU0:533.333 MHz, CPU1:533.333 MHz,
CCB:266.667 MHz,
DDR:333.333 MHz (666.667 MT/s data rate) (Asynchronous), LBC:16.667 MHz
L1: D-cache 32 kB enabled
I-cache 32 kB enabled
Board: P1020RDB Rev
MB-351Z Ver.T03 2012-06-13
I2C: ready
DRAM: Configuring DDR for 666.667 MT/s data rate
DDR: 512 MiB (DDR3, 32-bit, CL=6, ECC off)
FLASH: 2 MiB
L2: 256 KB enabled
NAND: 256 MiB
EEPROM: NXID v0
eTSEC2 is in sgmii mode.
PCIE2: connected to Slot 1 as Root Complex (base addr ffe09000)
PCIE2: Bus 00 - 00
PCIE1: connected to Slot 2 as Root Complex (base addr ffe0a000)
PCIE1: Bus 01 - 01
In: serial
Out: serial
Err: serial
Net: eTSEC1: No support for PHY id ffffffff; assuming generic
eTSEC3: No support for PHY id ffffffff; assuming generic
Init switch to forwarding mode... Done
eTSEC1, eTSEC2, eTSEC3
Hit any key to stop autoboot: 0
NAND read: device 0 offset 0x5100000, size 0x100000
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
1048576 bytes read: OK
NAND read: device 0 offset 0x5200000, size 0x1000000
16777216 bytes read: OK
## Booting kernel from Legacy Image at 01000000 ...
Image Name: Linux-3.18.43
Created: 2019-04-08 12:46:24 UTC
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 2408259 Bytes = 2.3 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 00c00000
Booting using the fdt blob at 0xc00000
Uncompressing Kernel Image ... OK
Loading Device Tree to 00ffa000, end 00fffb18 ... OK
[ 0.000000] Using P1020 RDB machine description
[ 0.000000] Memory CAM mapping: 256/256 Mb, residual: 0Mb
[ 0.000000] Linux version 3.18.43 (jenkins@kar-nsgci-node-21) (gcc version 5.4.0 (LEDE GCC 5.4.0 1-373-b15c4b2a-e9f0c31) ) #0 SMP Mon Apr 8 12:46:24 2019
[ 0.000000] CPU maps initialized for 1 thread per core
[ 0.000000] bootconsole [udbg0] enabled
setup_arch: bootmem
mpc85xx_rdb_setup_arch()
[ 0.000000] MPC85xx RDB board from Freescale Semiconductor
arch: exit
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00000000-0x1fffffff]
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x1fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x1fffffff]
[ 0.000000] MMU: Allocated 1088 bytes of context maps for 255 contexts
[ 0.000000] PERCPU: Embedded 9 pages/cpu @c090e000 s6144 r8192 d22528 u36864
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
[ 0.000000] Kernel command line: root=/dev/mtdblock10 console=ttyS0,115200
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Sorting __ex_table...
[ 0.000000] Memory: 448588K/524288K available (3600K kernel code, 204K rwdata, 948K rodata, 180K init, 213K bss, 75700K reserved)
[ 0.000000] Kernel virtual memory layout:
[ 0.000000] * 0xfffdf000..0xfffff000 : fixmap
[ 0.000000] * 0xfdffd000..0xfe000000 : early ioremap
[ 0.000000] * 0xe1000000..0xfdffd000 : vmalloc & ioremap
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:512 nr_irqs:512 16
[ 0.000000] mpic: Setting up MPIC " OpenPIC " version 1.2 at ffe40000, max 2 CPUs
[ 0.000000] mpic: ISU size: 256, shift: 8, mask: ff
[ 0.000000] mpic: Initializing for 256 sources
[ 0.000014] clocksource: timebase mult[1e000005] shift[24] registered
[ 0.006702] pid_max: default: 32768 minimum: 301
[ 0.011456] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.018013] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.025837] mpic: requesting IPIs...
[ 0.032177] Brought up 2 CPUs
[ 0.040415] NET: Registered protocol family 16
[ 0.054172] Found FSL PCI host bridge at 0x00000000ffe09000. Firmware bus number: 0->0
[ 0.062048] PCI host bridge /pcie@ffe09000 (primary) ranges:
[ 0.067695] MEM 0x00000000a0000000..0x00000000bfffffff -> 0x00000000a0000000
[ 0.074910] IO 0x00000000ffc30000..0x00000000ffc3ffff -> 0x0000000000000000
[ 0.082060] /pcie@ffe09000: PCICSRBAR @ 0xfff00000
[ 0.087272] Found FSL PCI host bridge at 0x00000000ffe0a000. Firmware bus number: 0->0
[ 0.095140] PCI host bridge /pcie@ffe0a000 ranges:
[ 0.100008] MEM 0x00000000c0000000..0x00000000dfffffff -> 0x00000000c0000000
[ 0.107225] IO 0x00000000ffc20000..0x00000000ffc2ffff -> 0x0000000000000000
[ 0.114372] /pcie@ffe0a000: PCICSRBAR @ 0xfff00000
[ 0.134504] PCI: Probing PCI hardware
[ 0.138343] fsl-pci ffe09000.pcie: PCI host bridge to bus 0000:00
[ 0.144393] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 0.150552] pci_bus 0000:00: root bus resource [mem 0xa0000000-0xbfffffff]
[ 0.157427] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.163420] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.171550] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 0.177098] fsl-pci ffe0a000.pcie: PCI host bridge to bus 0001:02
[ 0.183150] pci_bus 0001:02: root bus resource [io 0x20000-0x2ffff] (bus address [0x0000-0xffff])
[ 0.192092] pci_bus 0001:02: root bus resource [mem 0xc0000000-0xdfffffff]
[ 0.198966] pci_bus 0001:02: root bus resource [bus 02-ff]
[ 0.204912] pci 0001:02:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.213046] pci 0001:02:00.0: PCI bridge to [bus 03-ff]
[ 0.218373] PCI: Cannot allocate resource region 0 of PCI bridge 1, will remap
[ 0.225545] PCI: Cannot allocate resource region 0 of device 0000:00:00.0, will remap
[ 0.233364] PCI: Cannot allocate resource region 0 of device 0001:02:00.0, will remap
[ 0.241242] pci 0000:00:00.0: BAR 0: no space for [mem size 0x00100000]
[ 0.247809] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x00100000]
[ 0.254767] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 0.259726] pci 0000:00:00.0: bridge window [mem 0xa0000000-0xbfffffff]
[ 0.266511] pci_bus 0000:00: Some PCI device resources are unassigned, try booting with pci=realloc
[ 0.275620] pci 0001:02:00.0: BAR 0: no space for [mem size 0x00100000]
[ 0.282173] pci 0001:02:00.0: BAR 0: failed to assign [mem size 0x00100000]
[ 0.289131] pci 0001:02:00.0: PCI bridge to [bus 03]
[ 0.294091] pci 0001:02:00.0: bridge window [io 0x20000-0x2ffff]
[ 0.300356] pci 0001:02:00.0: bridge window [mem 0xc0000000-0xdfffffff]
[ 0.307140] pci_bus 0001:02: Some PCI device resources are unassigned, try booting with pci=realloc
[ 0.334236] usbcore: registered new interface driver usbfs
[ 0.339780] usbcore: registered new interface driver hub
[ 0.345126] usbcore: registered new device driver usb
[ 0.350187] pps_core: LinuxPPS API ver. 1 registered
[ 0.355094] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.364318] PTP clock support registered
[ 0.369232] Switched to clocksource timebase
[ 0.374807] NET: Registered protocol family 2
[ 0.379977] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.387047] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.393512] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.399894] TCP: reno registered
[ 0.403081] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.408906] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.415422] NET: Registered protocol family 1
[ 0.420070] RPC: Registered named UNIX socket transport module.
[ 0.425956] RPC: Registered udp transport module.
[ 0.430628] RPC: Registered tcp transport module.
[ 0.435323] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.444128] futex hash table entries: 512 (order: 2, 16384 bytes)
[ 0.451121] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.457353] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.467430] msgmni has been set to 1004
[ 0.473255] io scheduler noop registered
[ 0.477109] io scheduler deadline registered (default)
[ 0.482518] pcieport 0001:02:00.0: enabling device (0106 -> 0107)
[ 0.531828] Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
[ 0.539303] console [ttyS0] disabled
[ 0.542890] serial8250.0: ttyS0 at MMIO 0xffe04500 (irq = 42, base_baud = 16666666) is a 16550A
[ 0.551559] console [ttyS0] enabled
[ 0.551559] console [ttyS0] enabled
[ 0.558496] bootconsole [udbg0] disabled
[ 0.558496] bootconsole [udbg0] disabled
[ 0.567096] serial8250.0: ttyS1 at MMIO 0xffe04600 (irq = 42, base_baud = 16666666) is a 16550A
[ 0.576886] console [ttyS0] disabled
[ 0.580565] console [ttyS0] enabled
[ 0.584920] ffe04600.serial: ttyS1 at MMIO 0xffe04600 (irq = 42, base_baud = 16666666) is a 16550
[ 0.594379] Generic RTC Driver v1.07
[ 0.599385] efe00000.nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x002249
[ 0.609450] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.614667] Amd/Fujitsu Extended Query version 1.3.
[ 0.619751] number of CFI chips: 1
[ 0.623735] 5 ofpart partitions found on MTD device efe00000.nor
[ 0.629788] Creating 5 MTD partitions on "efe00000.nor":
[ 0.635129] 0x000000000000-0x0000000e0000 : "NOR reserved"
[ 0.641600] 0x0000000e0000-0x0000000f0000 : "NOR env flash2"
[ 0.648105] 0x0000000f0000-0x000000100000 : "NOR env flash"
[ 0.654537] 0x000000100000-0x000000180000 : "NOR Normal mode"
[ 0.661166] 0x000000180000-0x000000200000 : "NOR Backup mode"
[ 0.668786] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[ 0.675207] nand: Micron MT29F2G08ABAEAWP
[ 0.679239] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[ 0.684933] nand: WARNING: ffa00000.flash: the ECC used on your system is too weak compared to the one required by the NAND chip
[ 0.697407] Bad block table found at page 131008, version 0x01
[ 0.704825] Bad block table found at page 130944, version 0x01
[ 0.712150] 7 ofpart partitions found on MTD device ffa00000.flash
[ 0.718378] Creating 7 MTD partitions on "ffa00000.flash":
[ 0.723898] 0x000000000000-0x000000100000 : "fdt1"
[ 0.729666] 0x000000100000-0x000001100000 : "uimage1"
[ 0.735600] 0x000001100000-0x000005100000 : "rootfs1"
[ 0.741629] 0x000005100000-0x000005200000 : "fdt2"
[ 0.747251] 0x000005200000-0x000006200000 : "uimage2"
[ 0.753180] 0x000006200000-0x00000a200000 : "rootfs2"
[ 0.759170] 0x00000a200000-0x000010000000 : "data"
[ 0.764949] eLBC NAND device at 0xffa00000, bank 1
[ 0.773967] libphy: Fixed MDIO Bus: probed
[ 0.779751] libphy: Freescale PowerQUICC MII Bus: probed
[ 0.785351] Create Marvell Switch PHY device 0x10 manually
[ 0.792239] libphy: Freescale PowerQUICC MII Bus: probed
[ 0.799048] fsl-gianfar soc@ffe00000:ethernet@B0000: enabled errata workarounds, flags: 0x4
[ 0.818331] fsl-gianfar soc@ffe00000:ethernet@B0000 eth0: mac: 00:1a:8c:34:25:ef
[ 0.825797] fsl-gianfar soc@ffe00000:ethernet@B0000 eth0: Running with NAPI enabled
[ 0.833488] fsl-gianfar soc@ffe00000:ethernet@B0000 eth0: RX BD ring size for Q[0]: 256
[ 0.841525] fsl-gianfar soc@ffe00000:ethernet@B0000 eth0: RX BD ring size for Q[1]: 256
[ 0.849561] fsl-gianfar soc@ffe00000:ethernet@B0000 eth0: TX BD ring size for Q[0]: 256
[ 0.857598] fsl-gianfar soc@ffe00000:ethernet@B0000 eth0: TX BD ring size for Q[1]: 256
[ 0.865918] fsl-gianfar soc@ffe00000:ethernet@B1000: enabled errata workarounds, flags: 0x4
[ 0.885145] fsl-gianfar soc@ffe00000:ethernet@B1000 eth1: mac: 00:1a:8c:34:25:f0
[ 0.892596] fsl-gianfar soc@ffe00000:ethernet@B1000 eth1: Running with NAPI enabled
[ 0.900285] fsl-gianfar soc@ffe00000:ethernet@B1000 eth1: RX BD ring size for Q[0]: 256
[ 0.908323] fsl-gianfar soc@ffe00000:ethernet@B1000 eth1: RX BD ring size for Q[1]: 256
[ 0.916360] fsl-gianfar soc@ffe00000:ethernet@B1000 eth1: TX BD ring size for Q[0]: 256
[ 0.924397] fsl-gianfar soc@ffe00000:ethernet@B1000 eth1: TX BD ring size for Q[1]: 256
[ 0.933291] fsl-gianfar soc@ffe00000:ethernet@B2000: enabled errata workarounds, flags: 0x4
[ 0.952551] fsl-gianfar soc@ffe00000:ethernet@B2000 eth2: mac: 00:1a:8c:34:25:f1
[ 0.960012] fsl-gianfar soc@ffe00000:ethernet@B2000 eth2: Running with NAPI enabled
[ 0.967704] fsl-gianfar soc@ffe00000:ethernet@B2000 eth2: RX BD ring size for Q[0]: 256
[ 0.975739] fsl-gianfar soc@ffe00000:ethernet@B2000 eth2: RX BD ring size for Q[1]: 256
[ 0.983776] fsl-gianfar soc@ffe00000:ethernet@B2000 eth2: TX BD ring size for Q[0]: 256
[ 0.991822] fsl-gianfar soc@ffe00000:ethernet@B2000 eth2: TX BD ring size for Q[1]: 256
[ 1.000247] usbcore: registered new interface driver cdc_eem
[ 1.006084] usbcore: registered new interface driver cdc_ncm
[ 1.011870] usbcore: registered new interface driver huawei_cdc_ncm
[ 1.018253] usbcore: registered new interface driver qmi_wwan
[ 1.024111] usbcore: registered new interface driver cdc_mbim
[ 1.029903] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.036590] ehci-pci: EHCI PCI platform driver
[ 1.041161] ehci-platform: EHCI generic platform driver
[ 1.046631] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.053074] ohci-pci: OHCI PCI platform driver
[ 1.057644] ohci-platform: OHCI generic platform driver
[ 1.063164] /soc@ffe00000/usb@22000: Invalid 'dr_mode' property, fallback to host mode
[ 1.071324] fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
[ 1.078011] fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
[ 1.085411] fsl-ehci fsl-ehci.0: irq 28, io mem 0xffe22000
[ 1.101246] fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
[ 1.107700] hub 1-0:1.0: USB hub found
[ 1.111539] hub 1-0:1.0: 1 port detected
[ 1.116050] usbcore: registered new interface driver cdc_acm
[ 1.121755] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 1.129880] usbcore: registered new interface driver cdc_wdm
[ 1.135581] booke_wdt: powerpc book-e watchdog driver loaded
[ 1.142493] talitos ffe30000.crypto: hwrng
[ 1.148252] talitos ffe30000.crypto: md5-talitos alg registration failed
[ 1.155007] talitos ffe30000.crypto: sha1-talitos alg registration failed
[ 1.161827] talitos ffe30000.crypto: sha224-talitos alg registration failed
[ 1.168826] talitos ffe30000.crypto: sha256-talitos alg registration failed
[ 1.175821] talitos ffe30000.crypto: sha384-talitos alg registration failed
[ 1.182812] talitos ffe30000.crypto: sha512-talitos alg registration failed
[ 1.189804] talitos ffe30000.crypto: hmac-md5-talitos alg registration failed
[ 1.196969] talitos ffe30000.crypto: hmac-sha1-talitos alg registration failed
[ 1.204228] talitos ffe30000.crypto: hmac-sha224-talitos alg registration failed
[ 1.211655] talitos ffe30000.crypto: hmac-sha256-talitos alg registration failed
[ 1.219091] talitos ffe30000.crypto: hmac-sha384-talitos alg registration failed
[ 1.226521] talitos ffe30000.crypto: hmac-sha512-talitos alg registration failed
[ 1.233947] talitos ffe30000.crypto: fsl,sec3.3 algorithms registered in /proc/crypto
[ 1.242210] TCP: cubic registered
[ 1.245575] NET: Registered protocol family 17
[ 1.250131] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 1.262797] 8021q: 802.1Q VLAN Support v1.8
[ 1.275029] VFS: Mounted root (squashfs filesystem) readonly on device 31:10.
[ 1.282774] Freeing unused kernel memory: 180K (c0473000 - c04a0000)
[ 1.429243] usb 1-1: new high-speed USB device number 2 using fsl-ehci
[ 1.567969] hub 1-1:1.0: USB hub found
[ 1.572108] hub 1-1:1.0: 2 ports detected
[ 1.830175] blk_update_request: I/O error, dev mtdblock10, sector 1480
[ 1.836758] blk_update_request: I/O error, dev mtdblock10, sector 1482
[ 1.837239] SQUASHFS error: squashfs_read_data failed to read block 0xb1306
[ 1.837246] SQUASHFS error: Unable to read fragment cache entry [b1306]
E[ 1.837251] SQUASHFS error: Unable to read page, block b1306, size 85f0
rr[ 1.837267] SQUASHFS error: Unable to read fragment cache entry [b1306]
or[ 1.837271] SQUASHFS error: Unable to read page, block b1306, size 85f0
l[ 1.837284] SQUASHFS error: Unable to read fragment cache entry [b1306]
oa[ 1.837288] SQUASHFS error: Unable to read page, block b1306, size 85f0
di[ 1.837301] SQUASHFS error: Unable to read fragment cache entry [b1306]
ng[ 1.837305] SQUASHFS error: Unable to read page, block b1306, size 85f0
s[ 1.837319] SQUASHFS error: Unable to read fragment cache entry [b1306]
ha[ 1.837323] SQUASHFS error: Unable to read page, block b1306, size 85f0
red [ 1.918094] SQUASHFS error: Unable to read fragment cache entry [b1306]
li[ 1.924912] SQUASHFS error: Unable to read page, block b1306, size 85f0
br[ 1.931705] SQUASHFS error: Unable to read fragment cache entry [b1306]
ar[ 1.938496] SQUASHFS error: Unable to read page, block b1306, size 85f0
y [ 1.945288] SQUASHFS error: Unable to read fragment cache entry [b1306]
li[ 1.952065] SQUASHFS error: Unable to read page, block b1306, size 85f0
bu[ 1.958864] SQUASHFS error: Unable to read fragment cache entry [b1306]
bo[ 1.965651] SQUASHFS error: Unable to read page, block b1306, size 85f0
x.[ 1.972455] SQUASHFS error: Unable to read fragment cache entry [b1306]
so[ 1.979232] SQUASHFS error: Unable to read page, block b1306, size 85f0
: I/O error (needed by /sbin/init)
Error loading shared library libubus.so: I/O error (needed by /sbin/init)
[ 2.056984] blk_update_request: I/O error, dev mtdblock10, sector 1480
[ 2.063586] blk_update_request: I/O error, dev mtdblock10, sector 1482
[ 2.065235] SQUASHFS error: squashfs_read_data failed to read block 0xb1306
E[ 2.065242] SQUASHFS error: Unable to read fragment cache entry [b1306]
rr[ 2.065247] SQUASHFS error: Unable to read page, block b1306, size 85f0
or [ 2.090701] SQUASHFS error: Unable to read fragment cache entry [b1306]
lo[ 2.097499] SQUASHFS error: Unable to read page, block b1306, size 85f0
ading shared library libubox.so: I/O error (needed by /lib/libblobmsg_json.so)
Error loading shared library libubox.so: I/O error (needed by /lib/libjson_script.so)
Error relocating /lib/libblobmsg_json.so: blobmsg_add_field: symbol not found
Error relocating /lib/libblobmsg_json.so: blobmsg_check_attr: symbol not found
Error relocating /lib/libblobmsg_json.so: blobmsg_open_nested: symbol not found
Error relocating /lib/libblobmsg_json.so: blob_nest_end: symbol not found
Error relocating /lib/libblobmsg_json.so: blobmsg_add_field: symbol not found
Error relocating /lib/libblobmsg_json.so: blobmsg_check_attr: symbol not found
Error relocating /lib/libblobmsg_json.so: blobmsg_open_nested: symbol not found
Error relocating /lib/libblobmsg_json.so: blob_nest_end: symbol not found
Error relocating /lib/libjson_script.so: blobmsg_alloc_string_buffer: symbol not found
Error relocating /lib/libjson_script.so: blob_buf_free: symbol not found
Error relocating /lib/libjson_script.so: avl_find: symbol not found
Error relocating /lib/libjson_script.so: blob_buf_init: symbol not found
Error relocating /lib/libjson_script.so: blobmsg_realloc_string_buffer: symbol not found
Error relocating /lib/libjson_script.so: blobmsg_add_field: symbol not found
Error relocating /lib/libjson_script.so: avl_init: symbol not found
Error relocating /lib/libjson_script.so: __calloc_a: symbol not found
Error relocating /lib/libjson_script.so: avl_insert: symbol not found
Error relocating /lib/libjson_script.so: blobmsg_parse_array: symbol not found
Error relocating /lib/libjson_script.so: blobmsg_open_nested: symbol not found
Error relocating /lib/libjson_script.so: blob_nest_end: symbol not found
Error relocating /lib/libjson_script.so: blobmsg_add_string_buffer: symbol not found
Error relocating /lib/libjson_script.so: blobmsg_alloc_string_buffer: symbol not found
Error relocating /lib/libjson_script.so: blob_buf_free: symbol not found
Error relocating /lib/libjson_script.so: avl_find: symbol not found
Error relocating /lib/libjson_script.so: blob_buf_init: symbol not found
Error relocating /lib/libjson_script.so: blobmsg_realloc_string_buffer: symbol not found
Error relocating /lib/libjson_script.so: blobmsg_add_field: symbol not found
Error relocating /lib/libjson_script.so: avl_init: symbol not found
Error relocating /lib/libjson_script.so: __calloc_a: symbol not found
Error relocating /lib/libjson_script.so: avl_insert: symbol not found
Error relocating /lib/libjson_script.so: blobmsg_parse_array: symbol not found
Error relocating /lib/libjson_script.so: blobmsg_open_nested: symbol not found
Error relocating /lib/libjson_script.so: blob_nest_end: symbol not found
Error relocating /lib/libjson_script.so: blobmsg_add_string_buffer: symbol not found
Error relocating /sbin/init: uloop_run: symbol not found
Error relocating /sbin/init: ulog: symbol not found
Error relocating /sbin/init: avl_strcmp: symbol not found
Error relocating /sbin/init: avl_init: symbol not found
Error relocating /sbin/init: uloop_timeout_cancel: symbol not found
Error relocating /sbin/init: avl_insert: symbol not found
Error relocating /sbin/init: uloop_process_add: symbol not found
Error relocating /sbin/init: blobmsg_check_attr: symbol not found
Error relocating /sbin/init: ulog_open: symbol not found
Error relocating /sbin/init: uloop_timeout_set: symbol not found
Error relocating /sbin/init: uloop_init: symbol not found
Error relocating /sbin/init: uloop_run: symbol not found
Error relocating /sbin/init: ulog: symbol not found
Error relocating /sbin/init: avl_strcmp: symbol not found
Error relocating /sbin/init: avl_init: symbol not found
Error relocating /sbin/init: uloop_timeout_cancel: symbol not found
Error relocating /sbin/init: avl_insert: symbol not found
Error relocating /sbin/init: uloop_process_add: symbol not found
Error relocating /sbin/init: blobmsg_check_attr: symbol not found
Error relocating /sbin/init: ulog_open: symbol not found
Error relocating /sbin/init: uloop_timeout_set: symbol not found
Error relocating /sbin/init: uloop_init: symbol not found
[ 2.469321] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00007f00
[ 2.469321]
[ 2.478485] CPU: 0 PID: 1 Comm: init Not tainted 3.18.43 #0
[ 2.484063] Call Trace:
[ 2.486531] [df83de40] [c0383c2c] dump_stack+0x84/0xb0 (unreliable)
[ 2.492819] [df83de60] [c0381d24] panic+0xd8/0x214
[ 2.497629] [df83dec0] [c002b210] do_exit+0x3e4/0x854
[ 2.502693] [df83df10] [c002c580] do_group_exit+0x78/0xbc
[ 2.508105] [df83df30] [c002c5d8] __wake_up_parent+0x0/0x18
[ 2.513698] [df83df40] [c000de2c] ret_from_syscall+0x0/0x3c
[ 2.519284] --- interrupt: c01 at 0xb798a1e4
[ 2.519284] LR = 0xb7935430
[ 2.526703] Rebooting in 1 seconds..