This discussion has been locked.

You can no longer post new replies to this discussion. If you have a question you can start a new discussion

XG Firewall v18 MR-4: Feedback and experiences

New Thread to cover changes / feedback / experiences.

"Old" MR3 Thread: https://community.sophos.com/xg-firewall/f/discussions/123403/xg-firewall-v18-mr-3-feedback-and-experiences

Release Notes: https://community.sophos.com/xg-firewall/b/blog/posts/xg-firewall-v18-mr4-is-now-available

This thread was automatically locked due to age.

Top Replies

LuCar Toni over 3 years ago in reply to twister5800 +1

For XG Appliances, running in Active-Passive, we can accelerate more performance with the new fastpath technology. You should see more performance throughput on XGs running in Active-Passive. The HA…

0 SG001 over 3 years ago

Just upgraded from MR3 to MR4 and found one issue.

Manual Pattern Update in airgap environment doesn't work anymore. I can confirm that it worked on MR3.

Uploaded the actual pattern file in WebGui but nothing happened.

Also there is no entry in /log/u2d_airgap.log
Cancel
Vote Up 0 Vote Down

Cancel
0 Ben@Network over 3 years ago

For testing purposes I migrated 2 XGs to 18-MR4 and I have the issue that one XG is in Sophos Central Firewall Manager still shown as MR3.

XG Console:

Sophos Central Firewall Manager:

Post

A reboot dosn't resolve the issue.

If a post solves your question please use the 'Verify Answer' button.
Cancel
Vote Up 0 Vote Down

Cancel
0 LuCar Toni over 3 years ago in reply to Ben@Network

Two firewalls or one Cluster? How long since the Update? Did you refresh the Cache of your browser?

__________________________________________________________________________________________________________________
Cancel
Vote Up 0 Vote Down

Cancel
0 Ben@Network over 3 years ago in reply to LuCar Toni

It is a single filrewall. I've updated the XG yesterday in the morning (it is more than 24 hours ago, the reboot is also more the 24 hours ago). I cleared the browser cache and use a private session, still shown as MR3. I also tested it with another PC, which normaly does not use the Central Console but shown as MR3 too.

If a post solves your question please use the 'Verify Answer' button.
Cancel
Vote Up 0 Vote Down

Cancel
0 rfcat_vk over 3 years ago

Hi folks,

I was hoping that there might be some improvements in the daily reports, but no filed agsin, still not very accurate. A good indicator that there is activity on your network only.

Ian

XG115W - v20.0.2 MR-2 - Home

XG on VM 8 - v21 GA

If a post solves your question please use the 'Verify Answer' button.
Cancel
Vote Up 0 Vote Down

Cancel
0 MarekDalke over 3 years ago

After upgrading to v18.04 MR-4 all XFRM/tunnel interfaces used for IPSec Site-to-Site VPNs are gone/missing/ no longer listed at CONFIGURE > Network > Interfaces
Cancel
Vote Up 0 Vote Down

Cancel
0 LuCar Toni over 3 years ago in reply to MarekDalke

Can you show us a screenshot of your WAN Interface? Is it a VLAN Interface on WAN and not expanded?

__________________________________________________________________________________________________________________
Cancel
Vote Up 0 Vote Down

Cancel
0 LuCar Toni over 3 years ago in reply to Ben@Network

Still the old version shown in Central? Can you check on the XG Firmware images, that MR4 is actually loaded? Just to be sure?

__________________________________________________________________________________________________________________
Cancel
Vote Up 0 Vote Down

Cancel
0 LuCar Toni over 3 years ago in reply to SG001

That sounds like an issue. Can you open a Case and link the Case ID to emmosophos ?

__________________________________________________________________________________________________________________
Cancel
Vote Up 0 Vote Down

Cancel
0 MarekDalke over 3 years ago in reply to LuCar Toni

Gosh, I've missed it. Thanks for the hint!
Cancel
Vote Up 0 Vote Down

Cancel