This discussion has been locked.

You can no longer post new replies to this discussion. If you have a question you can start a new discussion

AP 30 inactive

HHO-Tim over 8 years ago

Hello community.,

i have an AP 30 after recovery which is inactive. AP 30 is shortly reachable with a DHCP-Adress.

Firewall is UTM 9.402.

Is AP 30 now worthless junk or has anyone an idea what to do?

Best regards

Tim

This thread was automatically locked due to age.

0 sachingurung over 8 years ago

Hi Tim,

Please flash AP30 referring this link. Please make sure that the AP is successfully updated.

https://www.sophos.com/en-us/support/knowledgebase/118843.aspx

If you still get connection problem, please post the wireless.log lines so that I can further investigate.

Thanks

Sachin Gurung
Team Lead | Sophos Technical Support
Knowledge Base | @SophosSupport | Video tutorials
Remember to like a post. If a post (on a question thread) solves your question use the 'This helped me' link.
Cancel
Vote Up 0 Vote Down

Cancel

0 HHO-Tim over 8 years ago in reply to sachingurung

Hi Sachin,

i have flashed AP30 with the tool from your link. After succesful flashing and reset of AP, AP can be accepted in the WebAdmin and in the log i can see the following line:

2016:05:12-15:50:48 fw-1 awed[24461]: [A4001F5A51FBFA6] sent firmware /etc/wireless/firmware/AP30.uimage to device, releasing connection.

After that i can't see anything in the log and the AP shows slowly blinking led left and rigt, led in the middle is off.

Any idea?

0 TPok over 8 years ago in reply to HHO-Tim

Same here. Two out of five AP30 are bricked. Reanimating them with the reflashin tool works until you connect them to the UTM and they pull the new Firmware again.

Support case has been created.
Cancel
Vote Up 0 Vote Down

Cancel
0 HHO-Tim over 8 years ago in reply to TPok

OK, let me know if you know some news.
Cancel
Vote Up 0 Vote Down

Cancel
0 sachingurung over 8 years ago in reply to TPok

Hi,

Please DM me the case# which is with Sophos support.

I also suggest an upgrade on firmware v9.4, there is a reported bug NUTM-3066 in the previous firmware version.

Thanks

Sachin Gurung
Team Lead | Sophos Technical Support
Knowledge Base | @SophosSupport | Video tutorials
Remember to like a post. If a post (on a question thread) solves your question use the 'This helped me' link.
Cancel
Vote Up 0 Vote Down

Cancel
0 HHO-Tim over 8 years ago in reply to sachingurung

I have updated on all stable firmware versions 9.4 and the error is the same. Actually we use firmware 9.402-7.
Cancel
Vote Up 0 Vote Down

Cancel
0 TPok over 8 years ago in reply to HHO-Tim

Sophos Support confirmed this is a bug. BUG-ID: NUTM-4151

As a quick fix our AP30 will be replaced. But this only works if you have Support, of course.
Cancel
Vote Up 0 Vote Down

Cancel
0 RobertGreller over 8 years ago

Hi,

i have the same problem with an AP30 REV 1. Our firmware is 9.404-5.

I already used this tool https://community.sophos.com/kb/de-de/118843 and it flashed the firmware, then told me to disconnect the device.

When i plug the AP30 in again it won't find the UTM. Power LED flashes slowly and the Network LED flashes on every second beat.

Any solutions on that?

Thanks and greetings,

Robert
Cancel
Vote Up 0 Vote Down

Cancel
0 HHO-Tim over 8 years ago in reply to RobertGreller

Hi,

with firmware 9.404 our AP is ok.

Best regards

Tim
Cancel
Vote Up 0 Vote Down

Cancel
0 RobertGreller over 8 years ago in reply to HHO-Tim

Thanks for the reply, Tim!
Cancel
Vote Up 0 Vote Down

Cancel