Filtering

Hi Nicholas,

Check the following settings and post screenshots for the same.

Configure the Internal Network host in Allowed Network for DNS global settings.

Add Internal Network in the Allowed Network for Web Protection global settings.

If the websites are gettings blocked, do a policy helpdesk test and verify which Filter Action blocks the request. Allow the website from the same.

Thanks

Hi,

I tried what you said but everything you said seems to be set okay. The only thing I can think of is the External (Wan) down interface isn't showing any activity, perhaps I have that configured wrong? I have BT Openreach Fibre to the Cabinet in the UK. Also how will the incoming network traffic know to pass through the UTM, how do UTMs work exactly?

Thanks for your help

Nicholas

Can I set the UTM to automatically get the WAN settings from my Router. I use my ISP provided modem/router unit.

That depends on how your ISP modem/router is setup. But usually if it's also a router (where you could also connect a computer that then automatically works), you can indeed automatically have the interface setup by configuring it as a DHCP interface

By selecting "Dynamic IP" the interface will request an IP-address from your modem. Also make sure IPv4 Default GW is selected so your UTM knows where to send internet requests.

Hi,

Thanks for the guide although it doesn't seem to pick up an IP address from my router which is weird because apart from that DHCP on my network works fine. On my UTM IPv6 Default GW isn't an option but does that matter as IPv6 is not used much at the moment? Is there anyone here in the forums who uses Sophos UTM Home with a BT Infinity internet connection?

Also just checking clients that should have content controlled by the UTM don't have to be plugged in through the UTM do they? As long as the clients are connected with the same LAN with the same subnet etc it should be fine? As I say this is the first time ever that I've tried to implement an advanced network security system.

Nicholas

Clients don't have to be physically connected to the UTM. Being in the same subnet will suffice. They do however need the UTM as their default gateway so traffic to the internet travels through the UTM.

I'm afraid I cannot help you further with your Infinity connection. IPv6 doesn't have to be turned on if not used.

Guys, I've read through this and I think, Nicholas, you might want to do a factory reset of your UTM VM and start over, but it's really not clear what you're working with...

1. What hardware are you using to run the virtualization - a laptop?  What CPU?  How much RAM does it have.  Which virtualization?
2. How much RAM and how many Processors have you allocated to the UTM VM?
3. How many users will be on simultaneously?  What and whom do you want to control/protect?  Are you only interested in anti-virus for web surfing and filtering your kids' web accesses?
4. What connection speed do you get from BT?
5. Can the BT modem be put in bridge mode so that the UTM can have a public IP instead of something in 192.168.x.y?
6. Is the BT modem also a wireless router, or just a router and you have a separate wireless access point?

Cheers - Bob

Hi Bob,

1. Yes, a laptop. Intel Core i5-5250U CPU, 4GB RAM, VMWare.

2. 2GB ram and 1 processor

3. Probably 5 at the most at any one time. I don't want to use the really advanced features but things like anti virus, web filtering and basic firewall I would like to use.

4. I get 30mbps down and 6mbps up.

5. To be honest I'm not sure.

6. Yes, it is a modem and wireless router in one although I have a separate Ubiquiti UniFi wireless access point too, to extend the coverage.

Thanks

Nicholas

1. If you want to run ESXi or VMWare Workstation, you will want to expand your RAM.  At least to 8GB, but to 16 if possible.  Running the UTM on VMWare Player is not recommended except for experimenting - definitely not for protecting up to five people.  Select the VMXNET3 virtual NICs.

2. Bump that up to 3GB if you add items in #3.

3. Yes, with the limited resources at your disposal, you won't want to have Intrusion Prevention or application Control active.

4. Your setup should be able to handle that with the caveats listed here.

5. Usually, the best approach for home use is to bridge the modem, disable wireless and disable DHCP service.  This lets the UTM have a public IP.  Since you have a laptop with only a single, wired NIC, that's not practical.

5.a. If you apparently also want to be able to use the laptop, your best bet may be to configure a single Interface, Internal, that uses the wireless and forget about the wired connection.

5.b. You would then configure the UTM to have a fixed IP with the BT modem as default gateway and setup DHCP on the UTM or BT device to hand out the IP of the UTM as default gateway.  If you want to be able to control all traffic with the UTM, then set the BT device's firewall to block all traffic from IPs other than the UTM's "Internal (Address)" IP.

Thoughts?

Cheers - Bob

Hi,

Thanks for your help, I'm still really keen to get this working. 

I would like the BT Home Hub to continue to do the routing, DHCP allocation and DNS allocation. If possible I want traffic going to certain devices only to pass through the Sophos UTM. I tried setting the default gateway of my client device to the IP of my UTM but I couldn't get to any pages, the connection just timed out. 

Your help is appreciated (: 

Do you have masquerading rules?

I'm not quite sure what that means sorry ): But I believe the issue must be with the WAN interface. I would like my BT Home Hub Modem/ Wireless router combo unit to continue to do the routing a DCHP etc.

I'm not quite sure what that means sorry ): But I believe the issue must be with the WAN interface. I would like my BT Home Hub Modem/ Wireless router combo unit to continue to do the routing a DCHP etc.

He meant to check #3.1 in Rulz, Nicholas.

Cheers - Bob