This discussion has been locked.
You can no longer post new replies to this discussion. If you have a question you can start a new discussion

Teamviewer Connections Blocked In Proxy Standard Mode

Hi community,

last week our Teamviewer connections suddenly stopped working from one day to the other. After hours of searching the source of the issue, I finally reached the point where I can tell it is caused by the webfilter of our SG230 UTM 9.510-5. Following behaviour:

- proxy in standard mode
- webfilter log shows 504 errors with timeouts while trying to reach ping3.teamviewer.com
- tcpdump on client shows the the connection gets interrupted and tries to retransmit the initial packet several times
- firewall log shows blocked packages from client to teamviewer server (I assume the retransmit packages get blocked because they do not pass thru the webfilter but over 443)

If I switch to transparent mode and add the destination host to the skip list, the teamviewer connections start working again.

So my question is: how can I teach the SG in transparent mode to do the "same" it does with the hosts in the skip list in transparent mode?



This thread was automatically locked due to age.
Parents
  • Do you have the following Exception?

    Teamviewer Remote Access 
    Skipping: Sandstorm / SSL scanning
    Matching these URLs: ^https?://(?:[A-Za-z0-9-]+\.)+teamviewer\.com/?

    If that doesn't work in Standard mode, you must skip *.teamviewer.com in 'Proxy Settings' in your browser.

    Cheers - Bob

     
    Sophos UTM Community Moderator
    Sophos Certified Architect - UTM
    Sophos Certified Engineer - XG
    Gold Solution Partner since 2005
    MediaSoft, Inc. USA
  • Hi Bob,

    first things first, thank you very much for spending your time for help and answering our questions here. I realen appreciate the effort, I am doing the same for network monitoring. :D

    Yes I have this exeption and no, this proxy setting does not work.

    I also played around a lot with web filtering options, settings, website tagging, etc. Without any success...  well, at some point I got rid of webfilter and firewall log entries, but the connection still die not work.

  • Do you have an FQDN in 'Address' and *.teamviewer.com in 'Exceptions'?  If you do that, your browser should skip the Proxy in Standard mode.  The 'Transparent Mode Skiplist' does not apply in Standard Mode.

    Cheers - Bob

     
    Sophos UTM Community Moderator
    Sophos Certified Architect - UTM
    Sophos Certified Engineer - XG
    Gold Solution Partner since 2005
    MediaSoft, Inc. USA
  • I tried your suggestion, but it does not work.

    What I forgot to mention is, that our firewall does not connect to the internet directly. Because we are in a governmental network (called "KDN"), our SG forwards http/s traffic to a parent web proxy. That's why the settings on client side do not have any effect I guess. But: skipping our proxy on client side by entering the KDN proxy directly to the proxy settings does not work either.

    If I eliminate our SG from the equation by connecting a client directly to the KDN switch, teamviewer connections start working again.

    So:

    - no SG -> works
    - SG transparent with skiplist -> works
    - SG standard mode -> does not work

  • With the browser's 'LAN Settings' properly configured, it will work in Standard mode, Philipp.  That causes the browser to skip the Standard Proxy.  For my use of TeamViewer, I don't need to skip the Proxy as the Exception noted above solves the problem for me.  I don't know of any other needed configuration, but it has been several years...  You could check the Web Filtering log file to see what's getting tripped up.  If you do, please post back here to let us know.

    Cheers - Bob

     
    Sophos UTM Community Moderator
    Sophos Certified Architect - UTM
    Sophos Certified Engineer - XG
    Gold Solution Partner since 2005
    MediaSoft, Inc. USA
  • Hi Phillip,

    I agree with Bob, defining an exception should have the connection not traveling through proxy. With that configuration it is clear the reason is not UTM related if something is in the proxy logs.

    Maybe one thing which has sometimes crossed my way. Do you use static proxy settings on the client? sometimes an application doesn’t play well with wpad & co.

    Best

    Alex

    -

  • I know, Teamviewer has some wired connections in it. 

    So basically dumped Teamviewer 12 (i guess) couple of month ago.

    They connect via teamviewer.com and start to use http calls on a ip, which is wired for me. They have hardcoded IP addresses in their calls to access the internet. 

    Could be already fixed but wanted to share my thoughts about this. 

    __________________________________________________________________________________________________________________

Reply
  • I know, Teamviewer has some wired connections in it. 

    So basically dumped Teamviewer 12 (i guess) couple of month ago.

    They connect via teamviewer.com and start to use http calls on a ip, which is wired for me. They have hardcoded IP addresses in their calls to access the internet. 

    Could be already fixed but wanted to share my thoughts about this. 

    __________________________________________________________________________________________________________________

Children
No Data