This discussion has been locked.
You can no longer post new replies to this discussion. If you have a question you can start a new discussion

ATT U-Verse and Astaro

I just got ATT-Uverse in my house and I can't get the security gateway machine to connect with the ATT modem (external network card.)  Does anyone know what protocol I am suppose to use to configure my external card to get a line and link up status?

Thanks.


This thread was automatically locked due to age.
Parents
  • Any other thoughts on how to get Astaro set up with AT&T U-verse?  I'm new to Astaro and I'm also trying to set it up with U-verse.  One thing somewhat unique to U-verse is that it uses a 2WIRE Residential Gateway (RG).  The RG is the modem and router built into one device.  There is some configuration options available for firewall settings, etc., within the RG, but it is limited in comparison to a stand-alone router.
  • Can you bridge the 2wire?

    Barry
  • All the 2wire routers I've seen that are using DSL support bridged mode, but it's in a hidden menu... try searching dslreports.com... that's where I found the info on the hidden menu for one customer's 2wire router (they are on AT&T DSL).

    CTO, Convergent Information Security Solutions, LLC

    https://www.convergesecurity.com

    Sophos Platinum Partner

    --------------------------------------

    Advice given as posted on this forum does not construe a support relationship or other relationship with Convergent Information Security Solutions, LLC or its subsidiaries.  Use the advice given at your own risk.

  • I was on the DSLreports site looking something up, found this for you... 2 Wire - dslreports.com

    CTO, Convergent Information Security Solutions, LLC

    https://www.convergesecurity.com

    Sophos Platinum Partner

    --------------------------------------

    Advice given as posted on this forum does not construe a support relationship or other relationship with Convergent Information Security Solutions, LLC or its subsidiaries.  Use the advice given at your own risk.

  • Thanks for you replies.  I checked the DSL Reports link you provided and tried to follow the instructions to disable routing.  I was able to get into the configuration, but my 2Wire Residential Gateway does not seem to offer the settings as described.  

    Since the 2Wire is handling IP-TV and VOIP, I'm thinking it is not possible.  I was hoping to somehow re-route all HTTP/HTTPS traffic to the Astaro Gateway, but can't seem to find a way to accomplish it.
  • Take a look at the first post on this page:
    https://community.sophos.com/products/unified-threat-management/astaroorg/f/52/t/26032

    It's about FIOS, but maybe UVerse uses Moca too?

    A friend of a friend is an UVerse installer for AT&T... I'll ask him about it when I see him, but more googling, or posting on the DSLReports forums may be your best bet.

    Does the 2wire have any NAT options?
    Can you find the manual for it online?

    Barry
Reply Children
  • You have another alternative; put the Astaro in bridged mode inline between your internal switch / hub and the U-Verse router...

    CTO, Convergent Information Security Solutions, LLC

    https://www.convergesecurity.com

    Sophos Platinum Partner

    --------------------------------------

    Advice given as posted on this forum does not construe a support relationship or other relationship with Convergent Information Security Solutions, LLC or its subsidiaries.  Use the advice given at your own risk.

  • Bruce, that may not help if he needs to DNAT incoming traffic. (I'm assuming the 2wire is doing MASQ).

    dpulverizer or dman777, did you guys ever get connected at all?
    dman777, you were asking about the protocol... it should just be ethernet with DHCP.

    Barry
  • I'm willing to bet he can gain access to the NAT engine in the 2wire; they seem to be pretty sophisticated.

    CTO, Convergent Information Security Solutions, LLC

    https://www.convergesecurity.com

    Sophos Platinum Partner

    --------------------------------------

    Advice given as posted on this forum does not construe a support relationship or other relationship with Convergent Information Security Solutions, LLC or its subsidiaries.  Use the advice given at your own risk.

  • Howdy...

    Just wanted to let you know that we had a problem getting this setup at a friends place as well... after many hours of dinking with it and getting no where, I kind of started playing around with some odd ball ideas and bang, it worked.

    First off, put your ASG in the DMZ of your 2wire modem/router. The att guys say this is basically the same as a bridge... they say it, not me =P anyway...

    We had gone with a default ASG setup on a Dell GX270 with two nics. One on-board and one PCI. The first go around when the question came up about which nic would be the internal connection I picked eth0 (the default). Which left eth1 for the WAN side of things...

    Tried to connect with PPPoE with no luck, instant failed connection attempt every time. Wait 5 default seconds, repeat, fail again... (instantly)

    After re-installing ASG and trying again but this time making the eth1 the internal (LAN) nic and eth0 the WAN connection it worked great. We could get to the web and it was nice and fast.

    For testing, I re-installed ASG and tried it the first way again, with no luck. It simply wouldn't connect.

    Re-installed again the second way and it worked great (again)...

    Tried this on another GX270 but had to use the same IBM PCI Ethernet card from the first box, with the exact same results...

    So either PPPoE doesn't like the on-board Dell NIC or it has to be on eth0.

    Now this was simply my findings for my issue with the Dell GX270 trying to connect to U-Verse home DSL service. I'm not saying YOU must use eth0 for your WAN. It's simply what I had to do to make it work. 

    Maybe it will work for you?

    P.S. simply deleting the interfaces did not work for us, only re-installing ASG as a whole worked...
  • Interesting... do you know what chipset or driver the GX270 NIC uses?

    Barry
  • Interesting... do you know what chipset or driver the GX270 NIC uses?

    Barry


    Not off hand, but next time I'm at his house I'll look...

    Update: Intel 865G chipset
  • Got it to work with slightly different instructions:

    Internal eth0
    1.  Standard Ethernet Interface
    2.  Put in a static IP address
    3.  Put in a default gateway of 192.168.1.254

    External eth1 
    1.  Set to Cable (DHCP) Interface
    2.  Set Hostname to ..com
    3.  Put the U-Verse box into DMZ-Plus mode 
    4.    Must refresh the DHCP lease on eth1 which changes the IP address from 192.168.1.x to whatever the external IP address of the Uverse gateway.

    Once this was done, it worked.  Still working through other initial setup and configuration issues.

    John
  • Once the eth1 Network Interface has its new IP address from the UVerse 2Wire gateway, it is possible to establish a VPN connection but after 30-60 minutes the the VPN connection would disconnect.  Apparently, after 30-60 minutes the eth1 Network Interface loses the IP address given from the 2Wire box and renews with an IP address on the internal network (i.e. 192.168.1.x) and subsequently drops out of DMZ-Plus mode.  Any ideas as to why this drops out after 30+ minutes?

    Thanks,
    John