UTM does not recognize IP change on uplink interface

Hi Tpok, 

When the interface uses a dynamic address allocation scheme (such as DHCP or remote assignment), these definitions are automatically updated. All settings referring to these definitions, for example, firewall and NAT rules, will also automatically be updated with the changed addresses. What is the firmware version of the UTM? Any specific custom settings for Uplink or interface definitions? Is Auto Negotiation enable for the interface, check in Interfaces & Routing > Interfaces > Hardware.

Thanks,

Hi Sachin,

thanks for your answer but I think you missed the point in my first post. So please let me try to explain it a little further.

I know how the dynamic address allocation should work. And it works the first time the LTE router is connected or I manually trigger a renewal of the IP address. But if the connection is lost afterwards there seems to be no trigger for the UTM to renew the dynamic IP address. The behavior is the following:

First time connection (link goes up - WAN Interface des not have an address yet), LTE router is connected to the mobile network

• UTM sends a DHCPDISCOVER to the LTE router
• UTM gets the dynamic IP address (DHCPOFFER etc.) with a lease time
• Uplink Monitoring can now ping the monitoring hosts and recognizes the connection as UP
• now everything is working

Now the LTE router looses the connection to the mobile network

• Uplink Monitoring cannot ping the monitoring hosts anymore recognizes the connection as DOWN
• WAN interface keeps the dynamic IP address (because the lease time is not over)

Now the LTE router reconnects to the mobile network. If it gets the same IP address from the provider everything is fine. But let's assume it gets a different IP address

• WAN interface still keeps the old dynamic IP address. Nothing triggers the interface to get the new ip address
• Uplink Monitoring still cannot ping the monitoring hosts because the WAN IP is wrong

My question is, how is this supposed to work? Nothing seems to trigger the interface to get a new IP address automatically. I can manually push the "renew" button or set the link down and up again but this is not a solution.

Has anybody a working setup here or an idea how this should work?

Hi Sachin,

thanks for your answer but I think you missed the point in my first post. So please let me try to explain it a little further.

I know how the dynamic address allocation should work. And it works the first time the LTE router is connected or I manually trigger a renewal of the IP address. But if the connection is lost afterwards there seems to be no trigger for the UTM to renew the dynamic IP address. The behavior is the following:

First time connection (link goes up - WAN Interface des not have an address yet), LTE router is connected to the mobile network

• UTM sends a DHCPDISCOVER to the LTE router
• UTM gets the dynamic IP address (DHCPOFFER etc.) with a lease time
• Uplink Monitoring can now ping the monitoring hosts and recognizes the connection as UP
• now everything is working

Now the LTE router looses the connection to the mobile network

• Uplink Monitoring cannot ping the monitoring hosts anymore recognizes the connection as DOWN
• WAN interface keeps the dynamic IP address (because the lease time is not over)

Now the LTE router reconnects to the mobile network. If it gets the same IP address from the provider everything is fine. But let's assume it gets a different IP address

• WAN interface still keeps the old dynamic IP address. Nothing triggers the interface to get the new ip address
• Uplink Monitoring still cannot ping the monitoring hosts because the WAN IP is wrong

My question is, how is this supposed to work? Nothing seems to trigger the interface to get a new IP address automatically. I can manually push the "renew" button or set the link down and up again but this is not a solution.

Has anybody a working setup here or an idea how this should work?

I dont know if i get you right, but what if you specify a manual monitoring target, like 8.8.8.8?

Thanks for detailed explanation, as I mentioned in my previous response, the interfaces will automatically update itself with a new IP address. Verify one setting in Interfaces > Uplink Balancing > Monitoring Hosts > click on the wrenches option; what is the interval and timeout value set for the UTM to do the connectivity check here? 

Interval: Enter a time interval in seconds at which the hosts are checked.

Timeout: Enter a maximum time span in seconds for the monitoring hosts to send a response. If all monitoring hosts of an interface do not respond during this time, the interface will be regarded as dead.

Thanks,