This discussion has been locked.

You can no longer post new replies to this discussion. If you have a question you can start a new discussion

Can't cannot to Webadmin at all

Hi i just started to use the software edition of sophos firewall utm i install it using Vmware/hyper-v but when i install finished i type the Ip address it does not prompt me to the website or anything and yes i already type https in front and i even try access to Webadmin on my Host pc/Vmware to no avail.

The ip is https://192.168.2.1:4444

This thread was automatically locked due to age.

Parents

0 Leong Maks over 7 years ago

tried a different ip 192.168.5.10:4444 and already tried to Reinstall the ISO and it still Just won't access to the Webadmin(NO certificate error) Just Error Connection.
Cancel
Vote Up 0 Vote Down

Cancel
0 BAlfson over 7 years ago in reply to Leong Maks

I would not use a virtual disk smaller than 40GB. Your problem is that you're still trying to connect to WebAdmin without changing the IP address of a NIC on the device running the VM.

Cheers - Bob

Sophos UTM Community Moderator
Sophos Certified Architect - UTM
Sophos Certified Engineer - XG
Gold Solution Partner since 2005

MediaSoft, Inc. USA
Cancel
Vote Up 0 Vote Down

Cancel
0 Leong Maks over 7 years ago in reply to BAlfson

Tried everything i know from school but it still fails

Help..!
Cancel
Vote Up 0 Vote Down

Cancel
0 BAlfson over 7 years ago in reply to Leong Maks

Just make this change for the Realtek:

Cheers - Bob

Sophos UTM Community Moderator
Sophos Certified Architect - UTM
Sophos Certified Engineer - XG
Gold Solution Partner since 2005

MediaSoft, Inc. USA
Cancel
Vote Up 0 Vote Down

Cancel
0 Leong Maks over 7 years ago in reply to BAlfson

still not working.
Cancel
Vote Up 0 Vote Down

Cancel
0 BAlfson over 7 years ago in reply to Leong Maks

What ideas do you get from asking about this on a VMware discussion board? Please share here what you learn there.

Cheers - Bob

Sophos UTM Community Moderator
Sophos Certified Architect - UTM
Sophos Certified Engineer - XG
Gold Solution Partner since 2005

MediaSoft, Inc. USA
Cancel
Vote Up 0 Vote Down

Cancel

Reply

0 BAlfson over 7 years ago in reply to Leong Maks

What ideas do you get from asking about this on a VMware discussion board? Please share here what you learn there.

Cheers - Bob

Sophos UTM Community Moderator
Sophos Certified Architect - UTM
Sophos Certified Engineer - XG
Gold Solution Partner since 2005

MediaSoft, Inc. USA
Cancel
Vote Up 0 Vote Down

Cancel

Children

0 Leong Maks over 7 years ago in reply to BAlfson

I just looked up on youtube video like this https://www.youtube.com/watch?v=u_Xvje11R9s

https://www.youtube.com/watch?v=7banab64Lh0

and this https://www.youtube.com/watch?v=UvBijyNZv1I

Their using Vm so i assume Vmware can be used to but for the Configuration i have no idea.
Cancel
Vote Up 0 Vote Down

Cancel
0 Ivan Ong over 7 years ago in reply to Leong Maks
I suspect the VMware NICs you are using might have to be swapped around.

In my instance I had:

vNIC1 on VM Network

vNIC2 on LAB Network

Switch it around to:

vNIC1 on LAB Network

vNIC2 on VM Network

The vNICs does not match that on the Sophos UTM.

Hopefully that solves your problem.
Cancel
Vote Up 0 Vote Down

Cancel