This discussion has been locked.

You can no longer post new replies to this discussion. If you have a question you can start a new discussion

Can't cannot to Webadmin at all

Hi i just started to use the software edition of sophos firewall utm i install it using Vmware/hyper-v but when i install finished i type the Ip address it does not prompt me to the website or anything and yes i already type https in front and i even try access to Webadmin on my Host pc/Vmware to no avail.

The ip is https://192.168.2.1:4444

This thread was automatically locked due to age.

Parents

0 Leong Maks over 7 years ago

tried a different ip 192.168.5.10:4444 and already tried to Reinstall the ISO and it still Just won't access to the Webadmin(NO certificate error) Just Error Connection.
Cancel
Vote Up 0 Vote Down

Cancel
0 BAlfson over 7 years ago in reply to Leong Maks

I would not use a virtual disk smaller than 40GB. Your problem is that you're still trying to connect to WebAdmin without changing the IP address of a NIC on the device running the VM.

Cheers - Bob

Sophos UTM Community Moderator
Sophos Certified Architect - UTM
Sophos Certified Engineer - XG
Gold Solution Partner since 2005

MediaSoft, Inc. USA
Cancel
Vote Up 0 Vote Down

Cancel

Reply

0 BAlfson over 7 years ago in reply to Leong Maks

I would not use a virtual disk smaller than 40GB. Your problem is that you're still trying to connect to WebAdmin without changing the IP address of a NIC on the device running the VM.

Cheers - Bob

Sophos UTM Community Moderator
Sophos Certified Architect - UTM
Sophos Certified Engineer - XG
Gold Solution Partner since 2005

MediaSoft, Inc. USA
Cancel
Vote Up 0 Vote Down

Cancel

Children

0 Leong Maks over 7 years ago in reply to BAlfson

Tried everything i know from school but it still fails

Help..!
Cancel
Vote Up 0 Vote Down

Cancel
0 BAlfson over 7 years ago in reply to Leong Maks

Just make this change for the Realtek:

Cheers - Bob

Sophos UTM Community Moderator
Sophos Certified Architect - UTM
Sophos Certified Engineer - XG
Gold Solution Partner since 2005

MediaSoft, Inc. USA
Cancel
Vote Up 0 Vote Down

Cancel
0 Leong Maks over 7 years ago in reply to BAlfson

still not working.
Cancel
Vote Up 0 Vote Down

Cancel
0 BAlfson over 7 years ago in reply to Leong Maks

What ideas do you get from asking about this on a VMware discussion board? Please share here what you learn there.

Cheers - Bob

Sophos UTM Community Moderator
Sophos Certified Architect - UTM
Sophos Certified Engineer - XG
Gold Solution Partner since 2005

MediaSoft, Inc. USA
Cancel
Vote Up 0 Vote Down

Cancel
0 Leong Maks over 7 years ago in reply to BAlfson

I just looked up on youtube video like this https://www.youtube.com/watch?v=u_Xvje11R9s

https://www.youtube.com/watch?v=7banab64Lh0

and this https://www.youtube.com/watch?v=UvBijyNZv1I

Their using Vm so i assume Vmware can be used to but for the Configuration i have no idea.
Cancel
Vote Up 0 Vote Down

Cancel
0 Ivan Ong over 7 years ago in reply to Leong Maks
I suspect the VMware NICs you are using might have to be swapped around.

In my instance I had:

vNIC1 on VM Network

vNIC2 on LAB Network

Switch it around to:

vNIC1 on LAB Network

vNIC2 on VM Network

The vNICs does not match that on the Sophos UTM.

Hopefully that solves your problem.
Cancel
Vote Up 0 Vote Down

Cancel
+1 Jas Man over 7 years ago in reply to Leong Maks

The problem is, that your VM network adapters are set to NAT. With this setting you're not able to access the UTM from "outside". Only access from another VM within the same subnet will be possible.

You have to change at least the management network adapter in the VM settings to "Brigde" to get access from "outside" / the host system.

Then your UTM VM will get an IP address of your physical LAN if theres a DHCP server, and you should be able to access the UTM.

Jas
Cancel
Vote Up 0 Vote Down

Cancel