This discussion has been locked.

You can no longer post new replies to this discussion. If you have a question you can start a new discussion

UTM 9.3550 1 released

Just had one UTM advise that the software was available for installation.

Up2Date 9.355001 package description:

Remark:
System will be rebooted

News:
Security Update

Bugfix:
Fix [36375]: glibc security update (CVE-2015-7547) [9.35]

RPM packages contained:
glibc-2.11.3-17.95.2.1656.ga688674.rb4.i686.rpm
glibc-locale-2.11.3-17.95.2.1656.ga688674.rb4.i686.rpm
u2d-appctrl43-9-13.i686.rpm
ep-release-9.355-1.noarch.rpm

This thread was automatically locked due to age.

0 twister5800 over 8 years ago

There is another thread:
community.sophos.com/.../74978
I made it 2 minuts earlier :-D

-----

Best regards
Martin

Sophos XGS 2100 @ Home | Sophos v20 Technician
Cancel
Vote Up 0 Vote Down

Cancel
0 IanMorehouse over 8 years ago in reply to twister5800

I know, you posted yours while I was making a correction to mine and adding the fix list.

Ian,

home UTM 9.x running in ESXi 6 e3-1275v2

AP55c and AP10 (courtesy Astaro)

Three other UTMs, SUM and SFM in hibernation

XG 15.x MR3 in hibernation
Cancel
Vote Up 0 Vote Down

Cancel
0 twister5800 over 8 years ago in reply to IanMorehouse

:-)

-----

Best regards
Martin

Sophos XGS 2100 @ Home | Sophos v20 Technician
Cancel
Vote Up 0 Vote Down

Cancel
0 RobertHafner over 8 years ago

Updated and now the flow monitor is broken. I was a few versions behind so this may not be specifically because of this release.
Cancel
Vote Up 0 Vote Down

Cancel
0 BAlfson over 8 years ago in reply to RobertHafner

Robert, what do you mean by "broken?"

Cheers - Bob

Sophos UTM Community Moderator
Sophos Certified Architect - UTM
Sophos Certified Engineer - XG
Gold Solution Partner since 2005

MediaSoft, Inc. USA
Cancel
Vote Up 0 Vote Down

Cancel
0 RobertHafner over 8 years ago in reply to BAlfson

Normally you open it up and it doesn't have data yet, and then it updates with the various services it sees. Since updating all I see is the message saying that it doesn't have data yet, and it never updates that.
Cancel
Vote Up 0 Vote Down

Cancel
0 BAlfson over 8 years ago in reply to RobertHafner

I noticed that, after 30 seconds, there wasn't data in either of two UTMs I tested this on, but when I went back 10 minutes later, both flow monitors were constantly being updated. Does your experience change after a reboot of the UTM?

Cheers - Bob

Sophos UTM Community Moderator
Sophos Certified Architect - UTM
Sophos Certified Engineer - XG
Gold Solution Partner since 2005

MediaSoft, Inc. USA
Cancel
Vote Up 0 Vote Down

Cancel
0 MarkThompson over 8 years ago

My system is running fine, just updated about 30 minutes ago and it all appears fine, flow monitor working.
Cancel
Vote Up 0 Vote Down

Cancel
0 HardChargin over 8 years ago

Add one more successful update. Updated via Up2Date about 45 minutes ago. No apparent issues thus far. Flow monitor working and (relative to other 9.355-1 thread) Up2Date shows current version 9.355-1. I updated from 9.353-4 to 9.355-1 in one shot.
Cancel
Vote Up 0 Vote Down

Cancel
0 apijnappels over 8 years ago

Updated 2 more UTM's without problems.

Managing several Sophos firewalls both at work and at some home locations, dedicated to continuously improve IT-security and feeling well helping others with their IT-security challenges.
Cancel
Vote Up 0 Vote Down

Cancel