This discussion has been locked.
You can no longer post new replies to this discussion. If you have a question you can start a new discussion

Home license with wireless protection

Hi Guys,

I have an old SG135 appliance which was converted from UTM to run SG some while ago. The licenses have expired and I have set it up with the XG firewall in my home and this works with the base license which has wireless functionality which I use with an AP100. Unfortunately due to IPV6 support missing on the device I want to move back to the UTM software.

I have a UTM license file and have downloaded the recovery disk, but the license I have has an expired wireless protection subscription. Is it correct that on the UTM software the base networking package which does not expire does not include the wireless support so for this I will need a new license? If I go with the home license will this include wireless protection and allow me to use the AP100?

Lastly, I seem to remember that if you use the home license you need to delete a file from the installation (IIRC its /etc/asg but could be wrong), if this file is deleted does the appliance lose any other functionality? I don't have an LCD screen on this model, but want to use the appliance installation media as I need to install headless as I don't have a VGA monitor.

Thanks.
Andrew.



This thread was automatically locked due to age.
  • i use SG with Home license and Wireless protection.#

    The "software appliance" image you need for Home license don't install if this one file is found at the HDD.

    This image don't support the LCD (without hack).

    Don't know other missing features.

     

     


    Dirk

    Systema Gesellschaft für angewandte Datentechnik mbH  // Sophos Platinum Partner
    Sophos Solution Partner since 2003
    If a post solves your question, click the 'Verify Answer' link at this post.

  • Hi,

    Well I set up the UTM9 as discussed and it all seemed to go well but it doesn't appear I can configure IPV6 on that either. I am using a provider that gives me a connection over Ethernet and I need to use SLAAC to get the IPV6 details. When I enable IPV6 on the device it sits there and never shows anything in the system other than no IPV6 connectivity available. The watchdog just sits with the following in the log:

    2019:09:12-18:24:20 gollum ipv6_watchdog[10303]: Starting IPv6 address watchdog
    2019:09:12-18:24:25 gollum ipv6_watchdog[10303]: JSON "eth1", "up", { "gateway6": "::", "network6":"1"}
    2019:09:12-18:24:25 gollum ipv6_watchdog[10303]: JSON "eth1", "up", { "address6": "::", "netmask6": "0", "network6":"1" }
    2019:09:12-18:24:25 gollum ipv6_watchdog[10303]: Start of monitoring interface eth1(ifidx 3)
    2019:09:12-18:24:25 gollum ipv6_watchdog[10303]: Installing default route via fe80::2ab4:48ff:fe87:c9fb for interface eth1(ifidx 3)
    2019:09:12-18:24:25 gollum ipv6_watchdog[10303]: RA flags changed for interface eth1(ifidx 3): NONE -> SENT,RCVD,OTHER,READY

    Any suggestions? Thinking of giving up at this stage until XG has better iPV6 support.

    Andrew.

  • Hi Dirk, schönen guten tag,
    Question.....
    You mentioned: "I use SG with Home license and Wireless protection.#
    The "software appliance" image you need for Home license don't install if this one file is found at the HDD. "

    I have the home license on my SG135 running with 9.510-5
    Deleted the asg file, installed newly created home license in myutm portal.

    Any idea how to enable wireless protection so I can use my AP100 again?
    Got the following message while trying to open 'Wireless Protection -> Wireless Networks' 
    "This page is disabled as you either do not have a relevant subscription"

    When I check The home license enabled options in my utmportal, wireless protection is enabled.
    Can you explain what is going on?
    Thnx in advance, Willem 



  • Check the license at MyUTM.

    Check the license-info within SG / management / licensing

    Try to reimport the license-file.

    ... if there is a difference, delete the home-license from within myUTM and generate a new file.


    Dirk

    Systema Gesellschaft für angewandte Datentechnik mbH  // Sophos Platinum Partner
    Sophos Solution Partner since 2003
    If a post solves your question, click the 'Verify Answer' link at this post.

  • Hoi Willem - your first post here - welcome to the UTM Community!

    Just to be clear for others that see this thread, the recommended solution for the 1xx-series appliances is to delete the asg file and then install the home-use license.

    For the appliances beginning with the 210, people will want to retain use of the LED panel.  Instead of deleting the file, rename it so that you can consult it to use the trick described in ASG 425 Display with home license.

    Cheers - Bob

     
    Sophos UTM Community Moderator
    Sophos Certified Architect - UTM
    Sophos Certified Engineer - XG
    Gold Solution Partner since 2005
    MediaSoft, Inc. USA