AP30, 9.400, VLANs, and ESXi - need help

I'm on 9.401 now; no luck so far.

I don't think the UTM upgraded the firmware on the AP30; at least I'm not seeing it in wireless.log.

Barry

Looks to me like the AP30 is only going to allow traffic on vlan1. You should move the AP30 into "All vlans" and that way it can be managed with vlan1 and accept any other vlan chucked at it eg vlan13

Hi,

I was hoping not to have to use trunking in the vSwitch, but it seems I can't avoid it.

I think I will have to setup another interface first for admin access, and delete and reconfigure the UTMs other interfaces.

Otherwise, I assume I could do 'Bridge to LAN' for the same LAN the AP is on, but no other LANs, right?

Thanks,

Barry

With vlans, you can never truly get away from trunking. If the device is vlan capable, you will need to use trunking unless you only want to use the one vlan to it. otherwise you would have to have multiple physical interfaces on it with one vlan per physical port.

Personally, for your setup, I would have let the UTM manage the vlans as well as the AP. Hope this helps.

OK...

I've decided to forget about the VLANs for WiFi for now...

1. I've removed VLAN1 from VMWare ESXi's vswitches

2. I've moved the AP30 to a non-VLAN switch, network .211

3. the AP still showed 'inactive' in the UTM, so I removed it, and reset the wireless settings.

The AP is not appearing in the UTM anymore, neither in the webadmin, the wireless.log, nor am I seeing it on tcpdump:

# tcpdump -i eth2 ether host 00:1a:8c:29:77:88
tcpdump: verbose output suppressed, use -v or -vv for full protocol decode
listening on eth2, link-type EN10MB (Ethernet), capture size 65535 bytes
22:28:37.583385 IP 0.0.0.0 > all-systems.mcast.net: igmp query v2
22:29:47.035490 IP 0.0.0.0 > all-systems.mcast.net: igmp query v2
22:30:18.345263 IP 0.0.0.0 > all-systems.mcast.net: igmp query v2
22:32:45.297657 IP 0.0.0.0 > all-systems.mcast.net: igmp query v2
22:33:16.657318 IP 0.0.0.0 > all-systems.mcast.net: igmp query v2

I'm not sure if the mcast packets are from the AP.

I'm guessing the AP is still trying to use VLANs; is there some way to reset it?
edit: yes, the AP is trying to use VLAN1... don't they have a fallback that will work without VLANs?

Thanks,

Barry

Hi Barry,

for me it looks like you ran into the vlan fallback issue we introduced with 9.400. This issue basically leads to an misbehaving AP and that is the reason why it is not automatically fixed in 9.401 for you.

The AP tries to connect over a specific VLAN, after it fails it reboots and tries again over the same VLAN over and over. So to get it back running you need to know which VLAN it tries to connect (the last one which was configured in the Access Point configuration before the AP went inactive). Then you need to provide this VLAN to the AP as a tagged VLAN and also make the UTM able to receive packets from this VLAN, configure the interfaces which belong to this VLAN accordingly (DHCP + allowed interfaces in wireless), then it should come online. After it gets online once it gets the firmware from 9.401 and then you can make the configuration as used before (with the VLAN on the AP as untagged).

Regards,
Emanuel

Hi Emanuel,

Let me make sure I understand...

1. I should get the AP30 hooked back to a UTM running 9.401 on VLAN1 or 13 (both were previously used, but the AP is definitely trying to use VLAN1 at the moment) and the firmware will be updated.

I will probably use a spare machine for this as I don't want to keep messing with my vSwitch.

2. Once the firmware is updated, can I move the AP30 back to my virtual system and use the AP30 with NO VLANs?

i.e. I will NOT be passing VLAN tags (trunking) in ESXi on the vSwitch to the UTM; can the AP30 with latest firmware work without VLANs at all?

I want to use 'Bridge to LAN' and have a couple non-bridged SSIDs, but I don't need to use 'Bridge to VLAN' anymore.

Thanks,

Barry

Can anyone confirm if my idea above will work?

Thanks,

Barry

Hi Barry,

yes, what you described above will work.

Regards,
Emanuel

Hi, I setup an old (former UTM) machine as a temp UTM (using the asg-9.401-11.1.ISO) to try to get the AP30 flashed...

I setup DHCP on the second interface, and plugged the AP30 into a NON-managed/non-VLAN switch with PoE and connected it to the UTM.

On the UTM, with tcpdump, I can see BOOTP/DHCP packets from the AP30, but I do not see a response from the UTM. Also, nothing shows up in wireless.log other than the startup messages.

I forgot to check the DHCP log.

Do I need to RESET the AP30 somehow?

Thanks,

Barry

Hi Barry,

on which VLAN do you see the DHCP requests? You can see this by "tcpdump -eni ethX". It is propably 1 or 13, then you need to provide a vlantagged interface on your UTM. This means for example if your AP is plugged into eth4 and the dhcp requests are coming with vlan 13 you need to configure a new vlan interface with hardware eth4 and vlantag 13. For this interface you also need a dhcp server and you need to add it in allowed interfaces under wireless protection.

Regards,
Emanuel

Hi,

Previously, I was seeing VLAN tagged packets on VLAN1, and non-tagged BOOTP/DHCP requests as well.

Last night, I only was looking at untagged packets.

Are you saying I need to setup the VLANs on the new UTM because I was using VLANs before? 

Because the docs don't seem to indicate it's necessary for a new setup... which is why I'm asking if I can do a RESET.

I'm not using a VLAN switch on this temporary UTM, if that matters, and my goal is to get the AP30 to work on my ESXi system with NO VLAN tags needed.

Thanks!
Barry

Hi,

Previously, I was seeing VLAN tagged packets on VLAN1, and non-tagged BOOTP/DHCP requests as well.

Last night, I only was looking at untagged packets.

Are you saying I need to setup the VLANs on the new UTM because I was using VLANs before? 

Because the docs don't seem to indicate it's necessary for a new setup... which is why I'm asking if I can do a RESET.

I'm not using a VLAN switch on this temporary UTM, if that matters, and my goal is to get the AP30 to work on my ESXi system with NO VLAN tags needed.

Thanks!
Barry

BTW, I never had to setup VLAN1 on the UTM previously; the UTM picked up the AP without it.

Does the 9.400 firmware bug cause it to now be necessary to setup VLAN1 myself?

Thanks