Thread Info
  • State Not Answered
  • Replies 18 replies
  • Subscribers 5 subscribers
  • Views 4656 views
  • Users 0 members are here
Options
Suggested

Using EAP Refresh 1 ISO to build a test XG

rfcat_vk

I have sent using a J1900 based box for various varsions of XG. So I decided to move the MR-9 to my E# box and use the J1900 as the EAP test box.

In summary a very painful exercise.

The EAP ISO has a new install process or at least the startup screen shows the SFLoader starting first, then you are offered 18.0.0.113 install with the standard question Y to install. All going well, takes awhile and when you get to the end the remove install software and enter y to reboot.

Nothing appears to be happening after the screen is cleared and a message booting 18.0.0.113 appears. Waited awhile, restarted the XG, again same screen, disk activity, buy no screen updates. Waited longer this time and console appears requesting password, this is good. Check various settings including setting the time. Tried logging in to the GUI, no success, waited, checked W10n for address assignment, it ha a valid address, but no connection.  Restart again, but no access. 

So a fresh install, same process as above, but this time waited longer (no screen activity) and eventually I was able to login to the GUI with finish install screen. Go through the normal steps and add XG device ID which synchronises but doesn't go any further. So restart browser, no joy. Restart XG and wait even longer, login via GUI and found installation is completed. What the heck?

Bugs,

GUI - insights doesn't't update even overnight

Notifications - goes fine until I change the state of the management port, then the circle of busy. Refresh browser and can use other GUI tabs. Check the notification page, still spinning. Restart XG, notification page still spinning. After initial use console does not respond until the XG is restarted.

I decide the J1900 is just too slow to make any changes or look at various logs.

Time to use a bigger box based on an e3-1240 v3. Way faster, but even less information during installation because the build software does not cooer to known how to configure a display card. 

Another install this time watching disk lights and the CD drive, guessed at answers based on previous installation experience. waited a short time until the NIC lights started flashing and logged into the GUI to be presented with the finish install screen. Same process as the J1900 installations but way faster.

Changed some of the notifications during the finish screen process because there were more screens presented.

Restarted and was able to login to see the normal XG GUI. Change a couple of rules and change MTA to legacy. Then tried to up date notifications and again the perpetual ball of busy.

 

Observations

1/. default MTA configuration and firewall rule appears to leave the XG open as a mail relay. Lots of failed relay attempts logged.

2/. Install process does not appear to have been checked very thoroughly

3/. something wrong with the console setup during installation

4/. No default video drivers provided in the ISO.

 

E3-1240 runs rings around J1900 for management. Both performed well for the speed test on my 50/20 data service

Yes, I know a long rant.

Ian

Parents
  • 0

    Hi Ian,

    My J1900 box has really been struggling with management since v17, at first I thought it was the PCIe SATA SSD I was using but when I switched types of SSD it made no changes.

    I'm getting ready to relegate the J1900 to "basic features" only for later versions of the XG, sadly.

    I'm also looking at an e3-12xx series processor for my next home XG box.

    Emile

  • 0 in reply to Emile Belcourt

    Hi Emile,

    The E3-1240 is an overkill, but that was all I had installed in a case.

    I looked at upgrading to the e3-1225 v6 and found the cost wan't worth it, no performance improvement and no power saving. If you need a new box, the e3-1225v6 will do the job very well,

    Mine sits around 20w except at restart time.

    The J1900 did work very well with the UTM 9.6, the interface was quite snappy before I migrated it to the XG.

    Ian

    XG115W - v20.0.2 MR-2 - Home

    XG on VM 8 - v21 GA

    If a post solves your question please use the 'Verify Answer' button.

  • 0 in reply to rfcat_vk

    Hi Ian,

    I'm not sure what route i'm going down, it has to be small and can be tucked out the way because the FW will be in the living room not my home office. Been looking at some HP Z230 Xeon workstations but i'd rather look into something a little less power hungry.

    The J1900 was a great processor and I have run XG on it since v15 GA but around v16.5/v17 I noticed the GUI be less responsive. Methinks it's time to move on!

    Well worth the 160 British Shmekels I paid for it though!

    I've been eyeing up the e3-1225v3 as that's the processor in the XG430 IIRC.

    Emile

Reply
  • 0 in reply to rfcat_vk

    Hi Ian,

    I'm not sure what route i'm going down, it has to be small and can be tucked out the way because the FW will be in the living room not my home office. Been looking at some HP Z230 Xeon workstations but i'd rather look into something a little less power hungry.

    The J1900 was a great processor and I have run XG on it since v15 GA but around v16.5/v17 I noticed the GUI be less responsive. Methinks it's time to move on!

    Well worth the 160 British Shmekels I paid for it though!

    I've been eyeing up the e3-1225v3 as that's the processor in the XG430 IIRC.

    Emile

Children
Unfiltered HTML