This discussion has been locked.

You can no longer post new replies to this discussion. If you have a question you can start a new discussion

Ipsec VPN - Route Based Connection

Hello folks,

Currently in Cyberoam devices we have an good option in Ipsec VPN config.

Route Based Connection / Bind With An Interface

This allow us usage Dynamic routing (OSPF) with VPN tunnels.

I can't see this option in Sophos Copernicus Firmware, could you inform me where is this feature? I need this to upgrade my Cyberoam devices to Sophos Copernicus Firmware :)

Best regards,

-Carlos

This thread was automatically locked due to age.

0 WagnerSilos over 8 years ago

Does someone have any idea about this topic!?

I'm on the same situation.
Cancel
Vote Up 0 Vote Down

Cancel
0 RichardLopez over 8 years ago

I posed a similar question and referenced yours question as an example to my account team and thisf the response.Does this work for you?

"If the desired result is to carry dynamic routing protocols over the IPSec VPN, we have that option even in v15. The below article describes how to configure this."

https://community.sophos.com/kb/en-US/123291
Cancel
Vote Up 0 Vote Down

Cancel
0 CarlosCesario over 8 years ago in reply to RichardLopez

Hi RichardLopez,

Thank you by your info.

Well, I already did verified this KB, but GRE in my case is not possible to be used.

"

Note:

GRE tunnels cannot be configured on Dynamic WAN interfaces like PPPoE and DHCP.

"

IPSEC support WAN interfaces with PPPoE and DHCP.

Currently I have many Cyberoam devices WAN interfaces configured with PPPoE and DHCP and other point is, these Cyberoam devices are running VPN service with IPSEC/Bind Interface routing. Therefore my question about this feature.
IMHO the migrate process should support this as other configs or at least support compatible/similar feature.

Best regards,

-Carlos

__

Analyst at Tecnomega
Cyberoam Certified Network & Security Expert (CCNSE)
Cancel
Vote Up 0 Vote Down

Cancel
0 sachingurung over 8 years ago

Hi Carlos,

This is a latest feature incorporated in 10.6.3 MR-5, I am not sure if that is supported in the XG firmware. I really wish I can provide you with some concrete information.

Provide me sometime to get an update on this matter.

Thanks

Sachin Gurung
Team Lead | Sophos Technical Support
Knowledge Base | @SophosSupport | Video tutorials
Remember to like a post. If a post (on a question thread) solves your question use the 'This helped me' link.
Cancel
Vote Up 0 Vote Down

Cancel
0 AlanT over 8 years ago

Hi Carlos,

This feature isn't offered in XG yet, but it's on the backlog, and we will add it in a future version. I don't have an estimate when yet, though.

Cheers,

-Alan
Cancel
Vote Up 0 Vote Down

Cancel
0 CarlosCesario over 8 years ago

Hi Sachin and AlanT.

Thank you, by yours answers.

I'm plannig ot migrate my all Cyberoam devices and most of them they use this feature. Therefore my question :)

Best regards,

-Carlos

__

Analyst at Tecnomega
Cyberoam Certified Network & Security Expert (CCNSE)
Cancel
Vote Up 0 Vote Down

Cancel
0 CarlosCesario over 7 years ago in reply to CarlosCesario

Hi folks.

How is going this feature ? It it already supported by XG firewalls ?

Best regards,

Carlos

__

Analyst at Tecnomega
Cyberoam Certified Network & Security Expert (CCNSE)
Cancel
Vote Up 0 Vote Down

Cancel
0 Carlos Cesario over 7 years ago in reply to CarlosCesario

Hello!

Does someone have any idea if this feature will be available in XG Firmware!?

We need migrate some Cyberoam devices using Ipsec VPN with OSPF routing to XG version.

Best regards,
Cancel
Vote Up 0 Vote Down

Cancel
0 Caio Silva over 6 years ago in reply to Carlos Cesario

Hello.

Do you have any forecast when this feature will be available in XG?
Thank you!
Cancel
Vote Up 0 Vote Down

Cancel
0 AlanT over 6 years ago in reply to Caio Silva

it's currently targeted for v18. We looked to do it sooner, but that wasn't practical.
Cancel
Vote Up 0 Vote Down

Cancel