Thread Info
  • State Suggested Answer
  • Locked Locked
  • Replies 4 replies
  • Answers 1 answer
  • Subscribers 4 subscribers
  • Views 11413 views
  • Users 0 members are here
Options
Suggested
This discussion has been locked.
You can no longer post new replies to this discussion. If you have a question you can start a new discussion

Netscaler to Load balance Virtual Email Appliance

David Pereira

Hi Everyone,

We are about to configure NetScaler to Load balance (internally) the traffic between two clustered appliances and I wonder if anyone else did it using NetScaler or another LB solution and what recommendations would you have in regards to configuration, persistency settings etc...

We are doing this to have a site and component resilient SMTP proxy in the event of a site or appliance failure.

 

thanks in advance.

David P



This thread was automatically locked due to age.
Parents
  • 0

    Hi David.

    In general you're playing with fire and I would never recommend a load balancer for email unless your talking 10's of millions of message per day.  It's simply not worth it.

    A record > firewall > loadbalancer > appliance > exchange 

    If not done correctly you will most certainly have issues.  In this scenario the load balancer does not let the mta connect to the appliance.. Instead it will replace the mta ip with its own.   From the appliances perspective you will break RDNS and Filtering options.  (mail from jimmy@gmail.com will be delivered from 10.10.10.1)  it will also prevent you from connection level blocking and delay queue will be impacted. 

    However if you really wish to do so..

    #1 ensure your load balancer allows the mta to connect to the appliance (if this is possible then configure the rest, if not your appliance will fail to identify bad senders)

    #2 configure filtering options

    A: Enable policy-level blocking of mail from known bad senders  (this will allow known bad hosts to relay mail instead of been dropped at connection level, it should not impact if the mail is dropped or not however ANY policy that matches may deliver the message)   recommended is to drop the connection at time of connecting.

    B: uncheck Enable proactive IP connection control for blocking suspicious hosts

    I do NOT recommend doing this unless absolutely necessary.  The BEST method for load balancing is via MX/A records each having its own ip and each pointing to its own appliance.

    For example.

    ;; ANSWER SECTION:
    sophos.com. 143 IN MX 10 mx4.sophos.com.
    sophos.com. 143 IN MX 10 mx5.sophos.com.
    sophos.com. 143 IN MX 10 mx6.sophos.com.
    sophos.com. 143 IN MX 10 mx3.sophos.com.
    sophos.com. 143 IN MX 10 mx2.sophos.com.
    sophos.com. 143 IN MX 10 mx1.sophos.com.

    ;; ADDITIONAL SECTION:
    mx1.sophos.com. 282 IN A 145.253.124.137
    mx2.sophos.com. 28 IN A 145.253.124.138
    mx3.sophos.com. 289 IN A 198.144.101.25
    mx4.sophos.com. 143 IN A 198.144.101.26
    mx5.sophos.com. 225 IN A 195.171.192.119
    mx6.sophos.com. 282 IN A 195.171.192.120

    every time an email is sent, its round robined through all of those addresses.. the is-spam email box probably gets 10M emails a day.   Unless your talking 10's or 100's of millions of emails like o365 or gmail .. dns is the prefered method.

    If you only have 1 public ip / A record.. even if you employ the worlds best load balancing for redundancy.. the second you get blacklisted, your done.

     

     

    If your idea is..

    A record > firewall > appliance > load balancer > exchange

    In all honesty.. there is no point in devoting hardware for this, simply go into configuration / routing / mail delivery servers  

    click add, from the drop down select "create mail delivery group"

    create 3 A records, give them all a priority of 10 and enter your downstream exchange servers.

     

Reply
  • 0

    Hi David.

    In general you're playing with fire and I would never recommend a load balancer for email unless your talking 10's of millions of message per day.  It's simply not worth it.

    A record > firewall > loadbalancer > appliance > exchange 

    If not done correctly you will most certainly have issues.  In this scenario the load balancer does not let the mta connect to the appliance.. Instead it will replace the mta ip with its own.   From the appliances perspective you will break RDNS and Filtering options.  (mail from jimmy@gmail.com will be delivered from 10.10.10.1)  it will also prevent you from connection level blocking and delay queue will be impacted. 

    However if you really wish to do so..

    #1 ensure your load balancer allows the mta to connect to the appliance (if this is possible then configure the rest, if not your appliance will fail to identify bad senders)

    #2 configure filtering options

    A: Enable policy-level blocking of mail from known bad senders  (this will allow known bad hosts to relay mail instead of been dropped at connection level, it should not impact if the mail is dropped or not however ANY policy that matches may deliver the message)   recommended is to drop the connection at time of connecting.

    B: uncheck Enable proactive IP connection control for blocking suspicious hosts

    I do NOT recommend doing this unless absolutely necessary.  The BEST method for load balancing is via MX/A records each having its own ip and each pointing to its own appliance.

    For example.

    ;; ANSWER SECTION:
    sophos.com. 143 IN MX 10 mx4.sophos.com.
    sophos.com. 143 IN MX 10 mx5.sophos.com.
    sophos.com. 143 IN MX 10 mx6.sophos.com.
    sophos.com. 143 IN MX 10 mx3.sophos.com.
    sophos.com. 143 IN MX 10 mx2.sophos.com.
    sophos.com. 143 IN MX 10 mx1.sophos.com.

    ;; ADDITIONAL SECTION:
    mx1.sophos.com. 282 IN A 145.253.124.137
    mx2.sophos.com. 28 IN A 145.253.124.138
    mx3.sophos.com. 289 IN A 198.144.101.25
    mx4.sophos.com. 143 IN A 198.144.101.26
    mx5.sophos.com. 225 IN A 195.171.192.119
    mx6.sophos.com. 282 IN A 195.171.192.120

    every time an email is sent, its round robined through all of those addresses.. the is-spam email box probably gets 10M emails a day.   Unless your talking 10's or 100's of millions of emails like o365 or gmail .. dns is the prefered method.

    If you only have 1 public ip / A record.. even if you employ the worlds best load balancing for redundancy.. the second you get blacklisted, your done.

     

     

    If your idea is..

    A record > firewall > appliance > load balancer > exchange

    In all honesty.. there is no point in devoting hardware for this, simply go into configuration / routing / mail delivery servers  

    click add, from the drop down select "create mail delivery group"

    create 3 A records, give them all a priority of 10 and enter your downstream exchange servers.

     

Children
No Data
Unfiltered HTML