This discussion has been locked.

You can no longer post new replies to this discussion. If you have a question you can start a new discussion

[XG 18] SD-WAN policies ignored? SFOS 18.0.0 GA-Build354

I upgraded to SFOS 18.0.0 GA-Build354 yesterday morning.

Under SFOS 18.0.0 GA-Build339 SD-WAN policies worked fairly well, sending traffic through specific interfaces based on subnet, user, etc.

However, since I the vast majority of traffic is going to the Active WAN-link. Very little traffic is going to the Backup link, even though the policy specifies to use it for certain source addresses.

Anyone else seeing this?

This thread was automatically locked due to age.

0 Arie over 4 years ago

Quick update: I changed the type of my secondary WAN-link from "backup" to "active" and I'm suddenly seeing traffic going to it.

Can the SD-WAN policies not send traffic to a backup link?
Cancel
Vote Up 0 Vote Down

Cancel
0 LuCar Toni over 4 years ago in reply to Arie

I did not test it in Build 354, but there are no changes at all to SD-WAN. So assuming there is no change, it should not changed in the working process.

Could you recover the old status with Backup Interface and show us your Sd-WAN Policy as a Screenshot?

Please take a look at the Gateway as well - Is it online?

__________________________________________________________________________________________________________________
Cancel
Vote Up 0 Vote Down

Cancel
0 Arie over 4 years ago in reply to LuCar Toni

I'll try to find some time over the weekend to revert.

Yes - both gateways are show as "up".
Cancel
Vote Up 0 Vote Down

Cancel
0 Arie over 4 years ago in reply to LuCar Toni

I'm still wondering whether the SD-WAN policies will send traffic to a WAN-link that's been set to "backup" instead of "active".
Cancel
Vote Up 0 Vote Down

Cancel
0 Arie over 4 years ago in reply to LuCar Toni

On a related note, I've noticed that the log page often doesn't show the outgoing port. Is this intentional?
Cancel
Vote Up 0 Vote Down

Cancel
0 LuCar Toni over 4 years ago in reply to Arie

Should be - I am pretty sure, it does.

__________________________________________________________________________________________________________________
Cancel
Vote Up 0 Vote Down

Cancel
0 Arie over 4 years ago in reply to LuCar Toni

LuCar Toni

Based on your reply I have done some more digging. Turns on that on my system shows ports only for connections that use a specific NAT-rule.

I haven't touched my NAT-rules after upgrading from v17, aside from a couple that I created when I cloned some FW-rules. Guess I'll need to take a look at my NAT-rules.
Cancel
Vote Up 0 Vote Down

Cancel
0 LuCar Toni over 4 years ago in reply to Arie

Please be careful: SNAT will only applied after the routing decision is already made. So Basically XG looks at the SD-WAN Routing table, choose a Rule, goes to the NAT Table and takes the specific SNAT Rule, matching for the traffic.

Do you have migrated SD-WAN Rule or not?

__________________________________________________________________________________________________________________
Cancel
Vote Up 0 Vote Down

Cancel
0 Arie over 4 years ago in reply to LuCar Toni

It's possible that SD-WAN was migrated from v17, but I'm not certain. Is there a way to tell?

I do have a lot of NAT-rules that resulted from the migration.
Cancel
Vote Up 0 Vote Down

Cancel
0 rfcat_vk over 4 years ago in reply to Arie

Hi,

you will see an SD-WAN rule for each migrated NAT which will be a linked NAT. You cannot edit the migrated SD-WAN rules, only delete.

Ian

XG115W - v20.0.2 MR-2 - Home

XG on VM 8 - v21 GA

If a post solves your question please use the 'Verify Answer' button.
Cancel
Vote Up 0 Vote Down

Cancel