Hi, I want to use a SD-RED20 behind an UTM with UTM 9.711-5 to connect a small office to headquarter. The connection from the SD-RED20 is established and working fine, for the local networks (few VLANs, split with a aruba, because the SD-20 can…

Hi, I have read that RED 15 has a maximum throughput of 90 Mbps. The head office has a fiber line of 300/300. The branch office has a fiber line of 200/200. The case is: Between this there is a RED 15. At the branch office, they log in with…

Hello, we have UTM 9 Firewall , we have a problem with RED 15, since yesterday one of RED15 cannot connect to our firewall, on saturday we installed the firmware update, after the update everything worked. we use another 3 REDs that work. here…

Hello Hope to get some advice from this great community, as this problem is driving me crazy Our specs: ASG Software, Firmware version: 9.705-3, runing on a VMWare ESXi 6.0U3 We have like 50 RED devices, models 10/15/15w/20, most of them in Standard…

After I set up a RED20, I plugged an AP into it, as I wanted to have an AP behind the RED20. I have it in Split-Tunnel Mode. The issue I had was that the AP would not show up in the list of new APs to authorize, on the UTM side. I read many many posts…

If I have to connect 1000 remote points with RED devices, which UTM do I have to choose? Or if the answer is a Virtual UTM, wich configuration do I need? Thanks UTM is going to provide access only to the RED devices, no more functionalities.

Is it possible to do the following: We have got a lab-environment in our datacenter. We installed a Sophos UTM and defined multiple VLANS which are attached to the VMs on our Hyper-V-Host. In our remote-office is a Sophos RED15W, connected via RED-Connection…

Hi, I need to find out how a RED device is connected to the UTM. I want to know whether the RED uses its WAN interface or its USB stick connection via LTE/UMTS/GSM etc. Is there a way to determine this via the REST API or any other way? I don't want…

Hello, we have two SG330 devices that operate in a hot-standby cluster. The internet connection in our main office, where the firewall cluster are located, is 50.000 Mbit/s SDSL (Up- and Download). If we use a new RED15w device on a good performing…

Hello, This has been going on for a little over a month now and seems to be getting worse. We have a RED 50 connected to our UTM 220 and following recent firmware upgrades (I think) it has become unstable. I see lots of other similar cases out there…

I have an internal client vlan (VLAN12) that I need to pass to a remote office. I purchased a RED50 because the literature says, it can handle vlan’s. Only, I’ve tried every which way that is suggested by the Sophos Community and I cannot get it to work…

Hi all, Apologies if this has already been covered, but I could not find a definitive answer. We have an SG230 at the Corporate Head Office and a number of RED 15w in staff member's homes. Our SG230's primary WAN link is a 100Mbit/sec in both…

Hi All, Thanks for reading.. I'm new to working with a RED 50 and RED 10 both connected to a UTM9. Due to the way the different networks were constructed, they are as follows: UTM (local 192.168.8.4) -> RED 10 -> local IP 192.168.9.1 RED 50 -…

We have 3 locations - one hosts the UTM9 and two have RED50 devices linking our sites together for voice and data. All sites have download/upload speeds of 100/20 mbps. Because everything routes through the UTM, however, the reality is that our two RED…

Followed instructions according to www.sophos.com/.../116573.aspx (Standard/Unified Mode). Connected RED10 to remote site, but I think it keeps rebooting. Power light stays on, 30 seconds later System light is on en 15 seconds later Internet light comes…

Our recent PCI Compliance scan came back failed because the RED service uses RC4-SHA. This is also one of the issues that the scanning company (Trustwave, who is used by our credit card processor, FirstData) will not allow to be overridden. If this is…

hi, I want to manage one server in remote location. I do not want to manage a whole network. I have utm and red 15. Is it possible to do it? If I plug in a wan link on red to switch and then server to lan on red then will that work?

Hi, ich have a very strange problem with the new RED 15. Setting: UTM 9.350-12 at the main office RED 15 with static IP behind an LTE-router at the remote location After the first configuration everything works fine. But after some hours the…