Hey guys, I have inherited this infrastructure from a previous Sysadmin. I'm in the process of putting all our printers into a dedicated Printer-VLAN. Some of our printers are at a neighboring building where we currently don't have a direct network…

Hi, we have a remote location with a RED running in standard / unified mode. Users are complaining that the internet is going down from time to time (status of the network connection is switching to no internet - visible in icon). Connection is via cable…

AM trying to reset a Sophos RED 15W previously connected with different network static up link. When i plugin it into a different network, it cannot connect to the provisioning server or even internet since it has static public ip address. Is there a…

After I set up a RED20, I plugged an AP into it, as I wanted to have an AP behind the RED20. I have it in Split-Tunnel Mode. The issue I had was that the AP would not show up in the list of new APs to authorize, on the UTM side. I read many many posts…

Is it possible to do the following: We have got a lab-environment in our datacenter. We installed a Sophos UTM and defined multiple VLANS which are attached to the VMs on our Hyper-V-Host. In our remote-office is a Sophos RED15W, connected via RED-Connection…

Hello, we have two SG330 devices that operate in a hot-standby cluster. The internet connection in our main office, where the firewall cluster are located, is 50.000 Mbit/s SDSL (Up- and Download). If we use a new RED15w device on a good performing…

Hello, We have set up a RED15w for a branch of one of our customers. It is configured in Standard/Split mode. There are WiFi access points on the remote site, AP30s. We have added host 1.2.3.4 in the splited networks so that the access points appear…

We have a RED15W at a remote office connected via the WAN port to a router. The RED15W used to work fine. We have switched to a different internet provider and now we are having errors on the RED15W device. We tested the internet connection on the LAN…

Hello, we seem to have a problem similar to this tread since 9.502-4, which might be caused by this fix: > Fix [NUTM-7962]: [WiFi] Split traffic not working for wireless clients on RED15w after upgrade to v9.5 Our setup worked well in 9.500 and…

Hallo, since our upgrade to UTM 9.500-9 last week Friday following problem occurs: - We use a Sophos SG310 now with UTM 9.500-9. Connected via RED are several branches in Europe and one branch in the US all with a Sophos RED15W in standard/split mode…

Hi Guys, I have a Head Office with a SG230, Dell 6248 (Layer 3), and a number of Internal VLANS - all working fine Dell 6248 is the Core Router, vLANs 10, 11, 12, 13, 15 setup with Interfaces (10.0.10.x, 10.0.11.x etc), IP routing etc and all working…

hello, we have a SG330 Cluster with 9.408-4 installed. we have now 2 brand new RED15W and have very poor Performance and Timeouts. We have installed the RED15w in two different Locations, same Problem. It makes no difference over LAN or WLAN. If i use…

Hi We use 8 RED15w for roadwarriors. We run the RED's in Standard/Unified mode, bridged to the LAN in the same IP Segment. Users behind the RED can connect to all resources in the LAN Segment, DHCP and DNS are working fine. But the only thing is…

How am I suppodes to setup/enable the WiFi on a RED 15w connected to a SG-105w? The W-Lan on this remote UTM is already up and working. In the Admin interface, I can see the interface wlan0 (which is enabled, working and bridged to eth0); as well as…

Hi all, Apologies if this has already been covered, but I could not find a definitive answer. We have an SG230 at the Corporate Head Office and a number of RED 15w in staff member's homes. Our SG230's primary WAN link is a 100Mbit/sec in both…

I try to add a RED15W to my UTM SG310 v9.4 but keep receiving the error: Client type does not match to RED ID. Please check the type of your RED device. I try it trough provisioning and USB but it won't add my new red to the UTM. The pull-down menu lets…