How to Flash a RED 50 rev1

i will keep the topic still open.

We have two RED 50 rev1 here and they stuck while booting.

I have added them more than 5 times again, but they will never get in touch with the UTM again. (no Log entry)

Due that the Flash Tool does not support REV 1 i've inspected the console and there are a lot of commands. Also it is possible to boot a new image.

But from where i can get this file?

Due the research i did not find a way to extract the image from a running RED 59 Rev1.

Does anyone have an idea?

Below a console output

MB351Z => print
baudrate=115200
bootcmd=setenv bootargs root=/dev/mtdblock10 console=ttyS0,115200; nand read 0xc00000 0x5100000 0x100000; nand read 0x1000000 0x5200000 0x1000000; bootm 0x1000000 - 0xc00000;
bootcmd_dram_test=ram_test
bootcmd_nandflash_test=nand_test 0 0x500000
bootcmd_norflash_test=flash_test 0xefe06000 0xefe4ffff
bootcmd_rtctest=rtc_test 20
bootdelay=3
bootloader_flash_update=protect off 0xeff00000 0xeff7ffff; erase 0xeff00000 0xeff7ffff; cp.b 0x100000 0xeff00000 0x80000; protect on 0xeff00000 0xeff7ffff; cmp.b 0x100000 0xeff00000 0x80000
consoledev=ttyS0
eth1addr=00:1A:8C:34:56:6E
eth2addr=00:1A:8C:34:56:6F
ethact=eTSEC1
ethaddr=00:1A:8C:34:56:6D
fdtaddr=c00000
fdtfile=mb351z.dtb
fdtkernel=uImage
filesize=360000
hwconfig=esdhc
lannerboot=setenv bootargs root=/dev/ram rw ramdisk_size=$ramdisksize rootdelay=10 console=ttyS0,115200;usb start;fatload usb 0 $loadaddr $fdtkernel;fatload usb 0 $ramdiskaddr $ramdiskfile;fatload usb 0 $fdtaddr $fdtfile;bootm $loadaddr $ramdiskaddr $fdtaddr;
loadaddr=1000000
loads_echo=1
netdev=eth0
ramdiskaddr=2000000
ramdiskfile=rootfs.ext2.gz.uboot
ramdisksize=2000000
usb_phy_type=ulpi
usbext2boot=setenv bootargs root=/dev/ram rw console=$consoledev,$baudrate; usb start;ext2load usb 0 $loadaddr $fdtkernel;ext2load usb 0 $fdtaddr $fdtfile;ext2load usb 0 $ramdiskaddr $ramdiskfile;bootm $loadaddr $ramdiskaddr $fdtaddr
usbfatboot=setenv bootargs root=/dev/ram rw ramdisk_size=$ramdisksize console=$consoledev,$baudrate; usb start;fatload usb 0 $loadaddr $fdtkernel;fatload usb 0 $fdtaddr $fdtfile;fatload usb 0 $ramdiskaddr $ramdiskfile;bootm $loadaddr $ramdiskaddr $fdtaddr

Environment size: 1680/65531 bytes

Here is the console output:

U-Boot 2010.12 (Jun 13 2012 - 18:57:31)

CPU0: P1020E, Version: 1.1, (0x80ec0011)
Core: E500, Version: 5.1, (0x80212051)
Clock Configuration:
CPU0:533.333 MHz, CPU1:533.333 MHz,
CCB:266.667 MHz,
DDR:333.333 MHz (666.667 MT/s data rate) (Asynchronous), LBC:16.667 MHz
L1: D-cache 32 kB enabled
I-cache 32 kB enabled
Board: P1020RDB Rev
MB-351Z Ver.T03 2012-06-13
I2C: ready
DRAM: Configuring DDR for 666.667 MT/s data rate
DDR: 512 MiB (DDR3, 32-bit, CL=6, ECC off)
FLASH: 2 MiB
L2: 256 KB enabled
NAND: 256 MiB
EEPROM: NXID v0
eTSEC2 is in sgmii mode.

PCIE2: connected to Slot 1 as Root Complex (base addr ffe09000)
PCIE2: Bus 00 - 00

PCIE1: connected to Slot 2 as Root Complex (base addr ffe0a000)
PCIE1: Bus 01 - 01

In: serial
Out: serial
Err: serial
Net: eTSEC1: No support for PHY id ffffffff; assuming generic
eTSEC3: No support for PHY id ffffffff; assuming generic
Init switch to forwarding mode... Done
eTSEC1, eTSEC2, eTSEC3
Hit any key to stop autoboot: 0

NAND read: device 0 offset 0x5100000, size 0x100000
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
1048576 bytes read: OK

NAND read: device 0 offset 0x5200000, size 0x1000000
16777216 bytes read: OK
## Booting kernel from Legacy Image at 01000000 ...
Image Name: Linux-3.18.43
Created: 2019-04-08 12:46:24 UTC
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 2408259 Bytes = 2.3 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 00c00000
Booting using the fdt blob at 0xc00000
Uncompressing Kernel Image ... OK
Loading Device Tree to 00ffa000, end 00fffb18 ... OK
[ 0.000000] Using P1020 RDB machine description
[ 0.000000] Memory CAM mapping: 256/256 Mb, residual: 0Mb
[ 0.000000] Linux version 3.18.43 (jenkins@kar-nsgci-node-21) (gcc version 5.4.0 (LEDE GCC 5.4.0 1-373-b15c4b2a-e9f0c31) ) #0 SMP Mon Apr 8 12:46:24 2019
[ 0.000000] CPU maps initialized for 1 thread per core
[ 0.000000] bootconsole [udbg0] enabled
setup_arch: bootmem
mpc85xx_rdb_setup_arch()
[ 0.000000] MPC85xx RDB board from Freescale Semiconductor
arch: exit
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00000000-0x1fffffff]
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x1fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x1fffffff]
[ 0.000000] MMU: Allocated 1088 bytes of context maps for 255 contexts
[ 0.000000] PERCPU: Embedded 9 pages/cpu @c090e000 s6144 r8192 d22528 u36864
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
[ 0.000000] Kernel command line: root=/dev/mtdblock10 console=ttyS0,115200
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Sorting __ex_table...
[ 0.000000] Memory: 448588K/524288K available (3600K kernel code, 204K rwdata, 948K rodata, 180K init, 213K bss, 75700K reserved)
[ 0.000000] Kernel virtual memory layout:
[ 0.000000] * 0xfffdf000..0xfffff000 : fixmap
[ 0.000000] * 0xfdffd000..0xfe000000 : early ioremap
[ 0.000000] * 0xe1000000..0xfdffd000 : vmalloc & ioremap
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:512 nr_irqs:512 16
[ 0.000000] mpic: Setting up MPIC " OpenPIC " version 1.2 at ffe40000, max 2 CPUs
[ 0.000000] mpic: ISU size: 256, shift: 8, mask: ff
[ 0.000000] mpic: Initializing for 256 sources
[ 0.000014] clocksource: timebase mult[1e000005] shift[24] registered
[ 0.006702] pid_max: default: 32768 minimum: 301
[ 0.011457] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.018014] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.025835] mpic: requesting IPIs...
[ 0.032176] Brought up 2 CPUs
[ 0.040413] NET: Registered protocol family 16

[ 0.054175] Found FSL PCI host bridge at 0x00000000ffe09000. Firmware bus number: 0->0
[ 0.062052] PCI host bridge /pcie@ffe09000 (primary) ranges:
[ 0.067699] MEM 0x00000000a0000000..0x00000000bfffffff -> 0x00000000a0000000
[ 0.074914] IO 0x00000000ffc30000..0x00000000ffc3ffff -> 0x0000000000000000
[ 0.082063] /pcie@ffe09000: PCICSRBAR @ 0xfff00000
[ 0.087274] Found FSL PCI host bridge at 0x00000000ffe0a000. Firmware bus number: 0->0
[ 0.095142] PCI host bridge /pcie@ffe0a000 ranges:
[ 0.100011] MEM 0x00000000c0000000..0x00000000dfffffff -> 0x00000000c0000000
[ 0.107227] IO 0x00000000ffc20000..0x00000000ffc2ffff -> 0x0000000000000000
[ 0.114375] /pcie@ffe0a000: PCICSRBAR @ 0xfff00000
[ 0.134501] PCI: Probing PCI hardware
[ 0.138340] fsl-pci ffe09000.pcie: PCI host bridge to bus 0000:00
[ 0.144389] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 0.150549] pci_bus 0000:00: root bus resource [mem 0xa0000000-0xbfffffff]
[ 0.157424] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.163417] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.171548] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 0.177096] fsl-pci ffe0a000.pcie: PCI host bridge to bus 0001:02
[ 0.183147] pci_bus 0001:02: root bus resource [io 0x20000-0x2ffff] (bus address [0x0000-0xffff])
[ 0.192089] pci_bus 0001:02: root bus resource [mem 0xc0000000-0xdfffffff]
[ 0.198963] pci_bus 0001:02: root bus resource [bus 02-ff]
[ 0.204908] pci 0001:02:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.213044] pci 0001:02:00.0: PCI bridge to [bus 03-ff]
[ 0.218371] PCI: Cannot allocate resource region 0 of PCI bridge 1, will remap
[ 0.225543] PCI: Cannot allocate resource region 0 of device 0000:00:00.0, will remap
[ 0.233362] PCI: Cannot allocate resource region 0 of device 0001:02:00.0, will remap
[ 0.241240] pci 0000:00:00.0: BAR 0: no space for [mem size 0x00100000]
[ 0.247807] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x00100000]
[ 0.254765] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 0.259725] pci 0000:00:00.0: bridge window [mem 0xa0000000-0xbfffffff]
[ 0.266510] pci_bus 0000:00: Some PCI device resources are unassigned, try booting with pci=realloc
[ 0.275619] pci 0001:02:00.0: BAR 0: no space for [mem size 0x00100000]
[ 0.282172] pci 0001:02:00.0: BAR 0: failed to assign [mem size 0x00100000]
[ 0.289129] pci 0001:02:00.0: PCI bridge to [bus 03]
[ 0.294089] pci 0001:02:00.0: bridge window [io 0x20000-0x2ffff]
[ 0.300354] pci 0001:02:00.0: bridge window [mem 0xc0000000-0xdfffffff]
[ 0.307138] pci_bus 0001:02: Some PCI device resources are unassigned, try booting with pci=realloc
[ 0.334286] usbcore: registered new interface driver usbfs
[ 0.339826] usbcore: registered new interface driver hub
[ 0.345173] usbcore: registered new device driver usb
[ 0.350231] pps_core: LinuxPPS API ver. 1 registered
[ 0.355130] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.364308] PTP clock support registered
[ 0.369235] Switched to clocksource timebase
[ 0.374812] NET: Registered protocol family 2
[ 0.379939] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.386995] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.393465] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.399846] TCP: reno registered
[ 0.403014] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.408853] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.415372] NET: Registered protocol family 1
[ 0.420041] RPC: Registered named UNIX socket transport module.
[ 0.425946] RPC: Registered udp transport module.
[ 0.430608] RPC: Registered tcp transport module.
[ 0.435303] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.444106] futex hash table entries: 512 (order: 2, 16384 bytes)
[ 0.451231] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.457569] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.467698] msgmni has been set to 1004
[ 0.473729] io scheduler noop registered
[ 0.477617] io scheduler deadline registered (default)
[ 0.482990] pcieport 0001:02:00.0: enabling device (0106 -> 0107)
[ 0.532402] Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
[ 0.539880] console [ttyS0] disabled
[ 0.543472] serial8250.0: ttyS0 at MMIO 0xffe04500 (irq = 42, base_baud = 16666666) is a 16550A
[ 0.552152] console [ttyS0] enabled
[ 0.552152] console [ttyS0] enabled
[ 0.559082] bootconsole [udbg0] disabled
[ 0.559082] bootconsole [udbg0] disabled
[ 0.567682] serial8250.0: ttyS1 at MMIO 0xffe04600 (irq = 42, base_baud = 16666666) is a 16550A
[ 0.577481] console [ttyS0] disabled
[ 0.581127] console [ttyS0] enabled
[ 0.585547] ffe04600.serial: ttyS1 at MMIO 0xffe04600 (irq = 42, base_baud = 16666666) is a 16550
[ 0.594996] Generic RTC Driver v1.07
[ 0.600012] efe00000.nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x002249
[ 0.610075] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.615292] Amd/Fujitsu Extended Query version 1.3.
[ 0.620368] number of CFI chips: 1
[ 0.624341] 5 ofpart partitions found on MTD device efe00000.nor
[ 0.630392] Creating 5 MTD partitions on "efe00000.nor":
[ 0.635747] 0x000000000000-0x0000000e0000 : "NOR reserved"
[ 0.642180] 0x0000000e0000-0x0000000f0000 : "NOR env flash2"
[ 0.648695] 0x0000000f0000-0x000000100000 : "NOR env flash"
[ 0.655132] 0x000000100000-0x000000180000 : "NOR Normal mode"
[ 0.661792] 0x000000180000-0x000000200000 : "NOR Backup mode"
[ 0.669405] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[ 0.675909] nand: Micron MT29F2G08ABAEAWP
[ 0.679950] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[ 0.685645] nand: WARNING: ffa00000.flash: the ECC used on your system is too weak compared to the one required by the NAND chip
[ 0.698114] Bad block table found at page 131008, version 0x01
[ 0.705566] Bad block table found at page 130944, version 0x01
[ 0.712892] 7 ofpart partitions found on MTD device ffa00000.flash
[ 0.719119] Creating 7 MTD partitions on "ffa00000.flash":
[ 0.724648] 0x000000000000-0x000000100000 : "fdt1"
[ 0.730392] 0x000000100000-0x000001100000 : "uimage1"
[ 0.736327] 0x000001100000-0x000005100000 : "rootfs1"
[ 0.742306] 0x000005100000-0x000005200000 : "fdt2"
[ 0.747941] 0x000005200000-0x000006200000 : "uimage2"
[ 0.753897] 0x000006200000-0x00000a200000 : "rootfs2"
[ 0.759883] 0x00000a200000-0x000010000000 : "data"
[ 0.765705] eLBC NAND device at 0xffa00000, bank 1
[ 0.774739] libphy: Fixed MDIO Bus: probed
[ 0.780507] libphy: Freescale PowerQUICC MII Bus: probed
[ 0.786111] Create Marvell Switch PHY device 0x10 manually
[ 0.793006] libphy: Freescale PowerQUICC MII Bus: probed
[ 0.799806] fsl-gianfar soc@ffe00000:ethernet@B0000: enabled errata workarounds, flags: 0x4
[ 0.819092] fsl-gianfar soc@ffe00000:ethernet@B0000 eth0: mac: 00:1a:8c:34:56:6d
[ 0.826550] fsl-gianfar soc@ffe00000:ethernet@B0000 eth0: Running with NAPI enabled
[ 0.834247] fsl-gianfar soc@ffe00000:ethernet@B0000 eth0: RX BD ring size for Q[0]: 256
[ 0.842286] fsl-gianfar soc@ffe00000:ethernet@B0000 eth0: RX BD ring size for Q[1]: 256
[ 0.850322] fsl-gianfar soc@ffe00000:ethernet@B0000 eth0: TX BD ring size for Q[0]: 256
[ 0.858359] fsl-gianfar soc@ffe00000:ethernet@B0000 eth0: TX BD ring size for Q[1]: 256
[ 0.866683] fsl-gianfar soc@ffe00000:ethernet@B1000: enabled errata workarounds, flags: 0x4
[ 0.885947] fsl-gianfar soc@ffe00000:ethernet@B1000 eth1: mac: 00:1a:8c:34:56:6e
[ 0.893399] fsl-gianfar soc@ffe00000:ethernet@B1000 eth1: Running with NAPI enabled
[ 0.901087] fsl-gianfar soc@ffe00000:ethernet@B1000 eth1: RX BD ring size for Q[0]: 256
[ 0.909124] fsl-gianfar soc@ffe00000:ethernet@B1000 eth1: RX BD ring size for Q[1]: 256
[ 0.917160] fsl-gianfar soc@ffe00000:ethernet@B1000 eth1: TX BD ring size for Q[0]: 256
[ 0.925197] fsl-gianfar soc@ffe00000:ethernet@B1000 eth1: TX BD ring size for Q[1]: 256
[ 0.934032] fsl-gianfar soc@ffe00000:ethernet@B2000: enabled errata workarounds, flags: 0x4
[ 0.953335] fsl-gianfar soc@ffe00000:ethernet@B2000 eth2: mac: 00:1a:8c:34:56:6f
[ 0.960773] fsl-gianfar soc@ffe00000:ethernet@B2000 eth2: Running with NAPI enabled
[ 0.968471] fsl-gianfar soc@ffe00000:ethernet@B2000 eth2: RX BD ring size for Q[0]: 256
[ 0.976510] fsl-gianfar soc@ffe00000:ethernet@B2000 eth2: RX BD ring size for Q[1]: 256
[ 0.984547] fsl-gianfar soc@ffe00000:ethernet@B2000 eth2: TX BD ring size for Q[0]: 256
[ 0.992593] fsl-gianfar soc@ffe00000:ethernet@B2000 eth2: TX BD ring size for Q[1]: 256
[ 1.001017] usbcore: registered new interface driver cdc_eem
[ 1.006857] usbcore: registered new interface driver cdc_ncm
[ 1.012634] usbcore: registered new interface driver huawei_cdc_ncm
[ 1.019026] usbcore: registered new interface driver qmi_wwan
[ 1.024885] usbcore: registered new interface driver cdc_mbim
[ 1.030675] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.037364] ehci-pci: EHCI PCI platform driver
[ 1.041933] ehci-platform: EHCI generic platform driver
[ 1.047402] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.053843] ohci-pci: OHCI PCI platform driver
[ 1.058413] ohci-platform: OHCI generic platform driver
[ 1.063944] /soc@ffe00000/usb@22000: Invalid 'dr_mode' property, fallback to host mode
[ 1.072092] fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
[ 1.078778] fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
[ 1.086160] fsl-ehci fsl-ehci.0: irq 28, io mem 0xffe22000
[ 1.101267] fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
[ 1.107728] hub 1-0:1.0: USB hub found
[ 1.111566] hub 1-0:1.0: 1 port detected
[ 1.116071] usbcore: registered new interface driver cdc_acm
[ 1.121780] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 1.129911] usbcore: registered new interface driver cdc_wdm
[ 1.135615] booke_wdt: powerpc book-e watchdog driver loaded
[ 1.142518] talitos ffe30000.crypto: hwrng
[ 1.148282] talitos ffe30000.crypto: md5-talitos alg registration failed
[ 1.155038] talitos ffe30000.crypto: sha1-talitos alg registration failed
[ 1.161859] talitos ffe30000.crypto: sha224-talitos alg registration failed
[ 1.168850] talitos ffe30000.crypto: sha256-talitos alg registration failed
[ 1.175842] talitos ffe30000.crypto: sha384-talitos alg registration failed
[ 1.182833] talitos ffe30000.crypto: sha512-talitos alg registration failed
[ 1.189825] talitos ffe30000.crypto: hmac-md5-talitos alg registration failed
[ 1.196990] talitos ffe30000.crypto: hmac-sha1-talitos alg registration failed
[ 1.204250] talitos ffe30000.crypto: hmac-sha224-talitos alg registration failed
[ 1.211677] talitos ffe30000.crypto: hmac-sha256-talitos alg registration failed
[ 1.219114] talitos ffe30000.crypto: hmac-sha384-talitos alg registration failed
[ 1.226543] talitos ffe30000.crypto: hmac-sha512-talitos alg registration failed
[ 1.233977] talitos ffe30000.crypto: fsl,sec3.3 algorithms registered in /proc/crypto
[ 1.242248] TCP: cubic registered
[ 1.245612] NET: Registered protocol family 17
[ 1.250168] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 1.262834] 8021q: 802.1Q VLAN Support v1.8
[ 1.275069] VFS: Mounted root (squashfs filesystem) readonly on device 31:10.
[ 1.282756] Freeing unused kernel memory: 180K (c0473000 - c04a0000)
[ 1.429254] usb 1-1: new high-speed USB device number 2 using fsl-ehci
[ 1.567731] hub 1-1:1.0: USB hub found
[ 1.571873] hub 1-1:1.0: 2 ports detected
[ 1.962750] init: Console is alive
[ 1.966416] init: - watchdog -
[ 2.521562] blk_update_request: I/O error, dev mtdblock10, sector 3628
[ 2.528160] blk_update_request: I/O error, dev mtdblock10, sector 3630
[ 2.529252] SQUASHFS error: squashfs_read_data failed to read block 0x1c1552
[ 2.529259] SQUASHFS error: Unable to read fragment cache entry [1c1552]
[ 2.529264] SQUASHFS error: Unable to read page, block 1c1552, size 117b8
[ 2.529281] SQUASHFS error: Unable to read fragment cache entry [1c1552]
[ 2.529285] SQUASHFS error: Unable to read page, block 1c1552, size 117b8
[ 2.529298] SQUASHFS error: Unable to read fragment cache entry [1c1552]
[ 2.529302] SQUASHFS error: Unable to read page, block 1c1552, size 117b8
[ 2.529313] SQUASHFS error: Unable to read fragment cache entry [1c1552]
[ 2.529317] SQUASHFS error: Unable to read page, block 1c1552, size 117b8
[ 2.529330] SQUASHFS error: Unable to read fragment cache entry [1c1552]
[ 2.529334] SQUASHFS error: Unable to read page, block 1c1552, size 117b8
[ 2.529346] SQUASHFS error: Unable to read fragment cache entry [1c1552]
[ 2.529350] SQUASHFS error: Unable to read page, block 1c1552, size 117b8
[ 2.529362] SQUASHFS error: Unable to read fragment cache entry [1c1552]
[ 2.529366] SQUASHFS error: Unable to read page, block 1c1552, size 117b8
[ 2.529378] SQUASHFS error: Unable to read fragment cache entry [1c1552]
[ 2.529382] SQUASHFS error: Unable to read page, block 1c1552, size 117b8
[ 2.529395] SQUASHFS error: Unable to read fragment cache entry [1c1552]
[ 2.529399] SQUASHFS error: Unable to read page, block 1c1552, size 117b8
[ 2.529413] SQUASHFS error: Unable to read fragment cache entry [1c1552]
[ 2.529416] SQUASHFS error: Unable to read page, block 1c1552, size 117b8
[ 2.529438] SQUASHFS error: Unable to read fragment cache entry [1c1552]
[ 2.529442] SQUASHFS error: Unable to read page, block 1c1552, size 117b8
[ 2.529455] SQUASHFS error: Unable to read fragment cache entry [1c1552]
[ 2.529459] SQUASHFS error: Unable to read page, block 1c1552, size 117b8
[ 2.529473] SQUASHFS error: Unable to read fragment cache entry [1c1552]
[ 2.529477] SQUASHFS error: Unable to read page, block 1c1552, size 117b8
[ 2.529491] SQUASHFS error: Unable to read fragment cache entry [1c1552]
[ 2.529495] SQUASHFS error: Unable to read page, block 1c1552, size 117b8
[ 2.529511] SQUASHFS error: Unable to read fragment cache entry [1c1552]
[ 2.529515] SQUASHFS error: Unable to read page, block 1c1552, size 117b8
[ 2.754794] init: - preinit -
Mounting ramdisk
Using /dev/mtdblock11 as data partition
Using /dev/mtdblock0 as self partition
[ 4.434616] jffs2: notice: (975) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 4.736198] random: jshn urandom read with 125 bits of entropy available
[ 4.931335] random: nonblocking pool is initialized
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 6.881277] fsl-gianfar soc@ffe00000:ethernet@B0000 eth0: Link is Up - 1Gbps/Full - flow control off
2[ 8.070916] mount_root: mounting /dev/root
[ 8.078142] mount_root: loading kmods from internal overlay
[ 8.103765] blk_update_request: I/O error, dev mtdblock10, sector 3628
[ 8.110367] blk_update_request: I/O error, dev mtdblock10, sector 3630
[ 8.113260] SQUASHFS error: squashfs_read_data failed to read block 0x1c1552
[ 8.113268] SQUASHFS error: Unable to read fragment cache entry [1c1552]
[ 8.113273] SQUASHFS error: Unable to read page, block 1c1552, size 117b8
Bus er[ 8.138038] mount_root: failed to launch kmodloader from internal overlay
ror
[ 8.719284] block: attempting to load /etc/config/fstab
[ 8.754452] block: extroot: not configured
[ 8.760618] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 8.848091] procd: - early -
[ 8.851150] procd: - watchdog -
Failed to connect to ubus
[ 9.613314] procd: - watchdog -
[ 9.616714] procd: - ubus -
[ 9.678994] procd: - init -
Please press Enter to activate this console.
[ 9.892663] blk_update_request: I/O error, dev mtdblock10, sector 3628
[ 9.899299] blk_update_request: I/O error, dev mtdblock10, sector 3630
[ 9.905967] SQUASHFS error: squashfs_read_data failed to read block 0x1c1552
[ 9.913088] SQUASHFS error: Unable to read fragment cache entry [1c1552]
[ 9.919891] SQUASHFS error: Unable to read page, block 1c1552, size 117b8
[ 11.975299] fsl-gianfar soc@ffe00000:ethernet@B1000 new_eth2: renamed from eth1
[ 12.001101] fsl-gianfar soc@ffe00000:ethernet@B2000 eth1: renamed from eth2
[ 12.020842] fsl-gianfar soc@ffe00000:ethernet@B1000 eth2: renamed from new_eth2
[ 15.629314] fsl-gianfar soc@ffe00000:ethernet@B0000 eth0: Link is Up - 1Gbps/Full - flow control off
[ 15.649337] fsl-gianfar soc@ffe00000:ethernet@B2000 eth1: Link is Up - 1Gbps/Full - flow control off
[ 15.713891] fsl-gianfar soc@ffe00000:ethernet@B1000 eth2: Link is Down
[ 31.480236] reboot: Restarting system

[ 9.913088] SQUASHFS error: Unable to read fragment cache entry [1c1552]
[ 9.919891] SQUASHFS error: Unable to read page, block 1c1552, size 117b8

Sadly it looks like you have a corrupt image/drive.

[ 9.913088] SQUASHFS error: Unable to read fragment cache entry [1c1552]
[ 9.919891] SQUASHFS error: Unable to read page, block 1c1552, size 117b8

Sadly it looks like you have a corrupt image/drive.