UTM HOME EDITION INSTALL ISSUE NOT WORKING AS IT SHOULD ON VMWARE WORKSTATION

Hi, and welcome to the UTM Community!

Please edit your post to change it into sentence case instead of all uppercase.

Cheers - Bob

Hi, and welcome to the UTM Community!

Please edit your post to change it into sentence case instead of all uppercase.

Cheers - Bob

I  have responded on the post Bob ,

Thank you

Can you post a diagram of your network setup? It's not very clear how you have everything connected.

Hi Thank you for your input,

I'm new to this stuff but I would give this a go.

I have a Virgin Super hub2, which is placed into modem mode. this opens one port at the back of the virgin router to be plugged else where. I have plugged this in to my host server which host's VMware workstation where UMT is configured. I have Assigned one nic on my server for the WAN which is this cable coming from the Virgin Super Hub Modem Port. Along with this I have config another nic on my host server as LAN, Which is where a cable is leaving this nic to be connected to my central Switch. Which has no VLAN very basic setup. This is than connecting all devices to network.

My trouble is i'm not very good with VMWare and virtual stuff. However With in VMware workstation when installing UMT I create two Network Cards and than with in VMware network management I assigned Vnet0 to the WAN nic on the host and Vnet 8 to the LAN nic on the host.  When setuping up UMT having issues with some UPlink where the they are showing but not really working. I have setup the nat masquerade, Also set the UMT as DHCP, Set the DNS, saw a 5 min Youtube video to config. That is all I know so far.

My confusing bite is, The VMware Network card connecting to the host NIC's Not sure how this should be done and how do I than do it within UMT setup please help.

Also when you put the Virgin Router in Modem mode it changes the gateway from 192.168.0.1 to 192.168.100.1 would this be a issue. what LAN ip range do I use. at the moment my lan ip range is 192.168.0.X

Which version of VMWare are you using? If you are using VMWare Workstation I'd recommend you read the user's manual as it's pretty detailed in setting up network connections.

Hello Kamran,

I want to help, but I do not understand your configuration either. A detailed description of your hardware and network configuration would help us understand better. 

I have a Sophos UTM running under VMware Fusion (Mac). I described its setup here:

https://community.sophos.com/products/unified-threat-management/f/52/p/27167/80436#80436

Even though it seems confusing and there are many Mac-specific instructions, VMware Fusion and VMware Workstation are very similar products, and you should be able to make it work for you. See the section called "Configuring VMware Virtual Machine". It may help a little.

Here is my home hardware configuration:

Internet <-> (cable) Cable Modem (ethernet) <-> Ethernet / USB 3 Adapter (External WAN, DHCP, IPv4/IPv6) <-> Mac mini (UTM in virtual machine) <-> Built-in Ethernet (LAN, private network, e.g. 10.x.x.x or 192.168.x.x) <-> Ethernet switch for home network

Here are a few VMware hints that may help you:

• I created a new virtual machine from the .iso file, but then I chose "Custom Configuration" so I could changed the settings and edit the .vmx file first before starting the .iso installer. 
• The virtual machine has two Ethernet adapters. You will have to add one. Both Ethernet adapters are set to Bridged mode in VMware.
• Sophos recommends that you edit your .vmx file in your virtual machine to change the network adapter drivers from "e1000" to "vmxnet3". There will be two entries in the file, one for each network adapter.
• For Operating System, choose Linux -> Suse Linux Enterprise 11, 64-bit.
• Choose the number of cores for your virtual machine carefully. You cannot change the number of cores after you install the UTM in your virtual machine. I have a quad (4) Core i7 in my Mac. I gave my UTM two cores in VMware. Do not give your virtual machine more than total hardware cores - 1. Hyperthread cores do not count.
• I chose 8192 MB for my UTM in VMware. My Mac has 16 GB of RAM installed. You can change the memory for your virtual machine memory at any time. Just shutdown the UTM first, then change the memory setting in VMware.

When you are ready, boot the VMware virtual machine. Follow the prompts during installation.

Tell us more about your system and network, and we may be able to help more. Good luck!

hi utmadm,

Thank you for your time. I still can't get UTM to work.

I posted a network Diagram with how I am trying to do this. I have turned off all firewall. I still can't understand why it doesn't work, I get no internet access on the end machine from the core switch. and Can't see any activity on the WAN. I'm very confused to how this program works. 

My understanding is with the Physical Firewall I have installed in the past. that you take the cable from the router/modem plug this in to the WAN and the LAN to the Switch. Not sure because this is a VM i'm messing this up but please do help i feel helpless. 

My Hardware Dell T110 II Power Edge Server with Three NIC''s Two are qlogic bcm5709c and 1 broad com. I have 32 gb ram and VM Workstation installed on this machine. The host os is W10 Pro. The VM's i have on here are UTM and Window Server 2012 R2. Vmware has three Virtual Networks Configured. VMXNET0, VMXNET1, VMXNET2.
VMXNET0 is the WAN which is Bridged to the qlogic bcm5709c NIC 1 46. VMXNET1 is the LAN which is Bridged to the qlogic bcm5709c NIC 2 47. Where the UTM Internal is assigned.  this is plugged in the core switch. VMXNET2 is the NIC for the Window SVR 2012 R2 which is coming from the core switch.

I noticed when the Virgin Router is in Modem Mode UTM won't pick up any info under Ethernet DHCP. however my host machine is picking the information with the IP address. Like wise evan when i Put the Virgin Router in Router Mode with DHCP. It does than pick up an address but can't see any traffic on the WAN. And any device Connected to the Core switch won't get any internet.. My main issue is that i can't get WAN to work ! thought LAN show's activity . How do i do this setup! I have tried your instruction for( Change the network adapter drivers from "e1000" to "vmxnet3") . I have also setup the Masquerading rule, and firewall rule as per Sophos Instruction.

Any one who uses VMworkstation and Virgin Router / Modem can they please advice on how I should setup this.

Based on the information you gave, is this a business installation?

Nope this is a home lab Environment