Thread Info
  • State Not Answered
  • Locked Locked
  • Replies 3 replies
  • Subscribers 6 subscribers
  • Views 1123 views
  • Users 0 members are here
Options
Suggested
This discussion has been locked.
You can no longer post new replies to this discussion. If you have a question you can start a new discussion

[9.706] Only sees one of my 2 Intel 82574L NICs (both worked in earlier 9.x versions)

BarryG

Hi,

I just freshly (re)installed 9.706009 on my MSI-IM945gse motherboard. (the system has been offline for a few years as I've been using virtualization lately, but it used to run 9.x well).

The board has TWO Intel 82574L PCI ethernet NICs, but the installer only sees one.

lspci shows both.

Let me know what other information is needed.
Thanks!

lspci -vvx:

01:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection
        Subsystem: Micro-Star International Co., Ltd. [MSI] Device 9830
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SER
R- FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort-
>SERR- <PERR- INTx+
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 16
        Region 0: Memory at feae0000 (32-bit, non-prefetchable) [size=128K]
        Region 2: I/O ports at ec80 [size=32]
        Region 3: Memory at feadc000 (32-bit, non-prefetchable) [size=16K]
        Capabilities: [c8] Power Management version 2
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+
)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
        Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+
                Address: 0000000000000000  Data: 0000
        Capabilities: [e0] Express (v1) Endpoint, MSI 00
                DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
                        ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
                DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
                        RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
                        MaxPayload 128 bytes, MaxReadReq 512 bytes
                DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-
                LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <128ns,
 L1 <64us
                        ClockPM- Surprise- LLActRep- BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt-
 ABWMgmt-
        Capabilities: [a0] MSI-X: Enable+ Count=3 Masked-
                Vector table: BAR=3 offset=00000000
                PBA: BAR=3 offset=00002000
        Capabilities: [100 v1] Advanced Error Reporting
                UESta:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP-
 ECRC- UnsupReq- ACSViol-
                UEMsk:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP-
 ECRC- UnsupReq- ACSViol-
                UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+
 ECRC- UnsupReq- ACSViol-
                CESta:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
                CEMsk:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
                AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
        Kernel driver in use: e1000e
        Kernel modules: e1000e
00: 86 80 d3 10 07 04 18 00 00 00 00 02 10 00 00 00
10: 00 00 ae fe 00 00 00 00 81 ec 00 00 00 c0 ad fe
20: 00 00 00 00 00 00 00 00 00 00 00 00 62 14 30 98
30: 00 00 00 00 c8 00 00 00 00 00 00 00 0a 01 00 00

02:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection
        Subsystem: Micro-Star International Co., Ltd. [MSI] Device 9830
        Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SER
R+ FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort-
>SERR- <PERR- INTx-
        Interrupt: pin A routed to IRQ 17
        Region 0: Memory at febe0000 (32-bit, non-prefetchable) [size=128K]
        Region 1: Memory at feb00000 (32-bit, prefetchable) [size=64]
        Region 2: I/O ports at <unassigned>
        Region 3: Memory at 00004000 (32-bit, non-prefetchable) [size=16K]
        Capabilities: [c8] Power Management version 2
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+
)
                Status: D1 NoSoftRst- PME-Enable- DSel=14 DScale=0 PME-
                Bridge: PM- B3+
        Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+
                Address: 0000000000000000  Data: 0000
        Capabilities: [e0] Express (v1) Endpoint, MSI 00
                DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
                        ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
                        RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
                        MaxPayload 128 bytes, MaxReadReq 512 bytes
                DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-
                LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <128ns,
 L1 <64us
                        ClockPM- Surprise- LLActRep- BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt-
 ABWMgmt-
        Capabilities: [a0] MSI-X: Enable- Count=3 Masked-
                Vector table: BAR=3 offset=00000000
                PBA: BAR=3 offset=00002000
        Capabilities: [100 v1] Advanced Error Reporting
                UESta:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP-
 ECRC- UnsupReq- ACSViol-
                UEMsk:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP-
 ECRC- UnsupReq- ACSViol-
                UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+
 ECRC- UnsupReq- ACSViol-
                CESta:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
                CEMsk:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
                AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
        Kernel modules: e1000e
00: 86 80 d3 10 03 01 10 00 00 00 00 02 10 00 00 00
10: 00 00 fe ff c8 00 00 00 01 00 00 00 00 40 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 62 14 30 98
30: 00 00 00 00 c8 00 00 00 00 00 00 00 0b 01 00 00




This thread was automatically locked due to age.
Parents
  • 0

    BTW, The recognized NIC is

    PCI Device ID:    0x10d3:0x9830

    and is using the e1000e driver module.

    I just installed the 9.707 up2date, with no change. But now I vaguely remember only the installer will configure new NICs.

  • 0 in reply to BarryG

    Hey Barry,

    Are you saying that you installed the 2nd NIC after you had run the UTM installation?  Does re-imaging from ISO solve this as you suspect?

    Cheers - Bob

     
    Sophos UTM Community Moderator
    Sophos Certified Architect - UTM
    Sophos Certified Engineer - XG
    Gold Solution Partner since 2005
    MediaSoft, Inc. USA
  • 0 in reply to BAlfson

    Hi Bob,

    No, both NICs are integrated on the motherboard.

    What I mean is that installing the version upgrade probably wouldn't have helped as it wouldn't have run the hardware detection phase.

    (which is only done on new install and would also require a new ISO with whatever fix is needed to detect the NIC)

    Is anyone from Sophos looking at this?

    I don't want to use my work account to submit a support ticket for my home firewall.

    thanks

Reply
  • 0 in reply to BAlfson

    Hi Bob,

    No, both NICs are integrated on the motherboard.

    What I mean is that installing the version upgrade probably wouldn't have helped as it wouldn't have run the hardware detection phase.

    (which is only done on new install and would also require a new ISO with whatever fix is needed to detect the NIC)

    Is anyone from Sophos looking at this?

    I don't want to use my work account to submit a support ticket for my home firewall.

    thanks

Children
No Data
Unfiltered HTML