Hi, one of our customers has the problem, that without RED tunnel comp. it is not possible to do ICMP larger than 1380bytes. When i activate compression the ICMP goes through - even with 9000bytes. i double checked everything, also went through…

Hi, I'm trying to setup a RED 15 at a remote location, which should connect to our main office network behind a Sophos UTM 9.5. I followed the instructions here https://community.sophos.com/kb/en-us/116573 to setup a Standard/Unified tunnel and it mostly…

Hi, is it possible to create a tunnel between two or more red devices directly (without passing data from one RED to the UTM and back to the other RED)?

Is there a way to update REDs individually to test the firmware before mass deployment? We had a few REDs not come back up after an upgrade.

Hi Everyone We have UTM9 configured with two external NICs and one internal NIC. External NIC #1: Managed Internet WAN with PPTP port only open. Connected to router and behind an external IBM firewall. External NIC #2: Directly connected via IPoE…

Hello everyone, I just added a RED10 to our UTM9 and chose Standard/Unified mode as we need the remote office to be working via the local office's public IP address. However, the remote office's clients shall not be able to access devices such as…

Hello, This has been going on for a little over a month now and seems to be getting worse. We have a RED 50 connected to our UTM 220 and following recent firmware upgrades (I think) it has become unstable. I see lots of other similar cases out there…

I have invested in a Sophos UTM 110/120 box which will replace my Asus router for my home address. The idea is to have a Qnap NAS at home which is synchronizing with a server at work for backup via a VPN connection between my home and the office. I…

Hi All, I'm having a weird problem with my AP, current IP address is 192.168.250.70, and can see AP in the UTM. I have an SSID called Employee with WPA2 Enterprise with a Radius in my Server Vlan. It seems the authenicate ok however when trying…

Hi all, we could implement a basically working L2 lan interconnect with a UTM9-UTM9 RED tunnel. There are two problems for which we need a solution: 1. the RED server site has 3 WAN uplinks. We would like to bind the RED tunnel to a specific WAN uplink…

Hello. I have a SG330 at main office connecting to a RED50 in branch office(KG). Connected to that RED is a Cisco switch with VLANs. I want the VLANs from main office to talk to branch office VLANs So on the SG330 Internal on eth9 - 10.0.0.248…

Right now my company just moved to a new UTM and we upgraded a few REDs to the RED15rev1. I read in the documentation that you needed to allow UDP3410 so it can communicate properly. Would we need just create a service definition for this port and allow…

We have a client with two sites. The main site has several subnets, on different interfaces of the UTM. The remote site has one subnet. Communications between the sites was facilitated by RED link (UTM as RED). This has been working perfectly for some…

We have some IP phones at a remote site which has limited bandwidth (currently connected to a RED50 using a standard / split tunnel) I am trying to setup a QOS rule so the phones always get a reserved chunk of the bandwidth as the site often maxes…

Hi is there any command to get the IPs of the connected REDs via command-line? I already tried cc get red but it only shows the internal name of the REDs, certs and so on, but no IPs. Regards Rolf

Hi there We use an UTM SG120 @9.355 and a RED15. One of the ethernet ports ist configured as a trunk port with various VLANs. Is it possible, one of these existing VLANs bridge to the RED? Concrete: VLAN 500 @eth3 with subnet 172.16.10.1/24 should…

I would like to connect a RED device out of line, so that its WAN interface is connected to the local LAN. This works and connects back to the UTM but can I then point a server at the RED WAN interface and have the RED route it out? Does anybody have…

Our recent PCI Compliance scan came back failed because the RED service uses RC4-SHA. This is also one of the issues that the scanning company (Trustwave, who is used by our credit card processor, FirstData) will not allow to be overridden. If this is…