My RED 50 is suddenly no longer making a connection. I can see on the modem that it is fetching an DHCP IP address, but the message "Network error" appears on the display. I tried to reflash the RED, but unfortunately it doesn't work either. ******…

Problem: SD RED 20 mit Wifi/WLAN Modul: Wifi AP deaktiviert sich selbst Wireless Protection -> Access Points -> Inactive Access Points Grund: Zugehöriger DHCP-Server ist konfiguriert auf „Clients with static mappings only“ (Network Services…

Hi, I have 2 UTM and one RED-SD20. The SD20 is working fine with 3 VLANs routed. (br0 with eth8, VLAN1, 2, 3 are set up on eth8) Now I want to setup a second RED-tunnel, but between 2 UTMs. Config for VLAN3, which should work on both RED-tunnels…

I know that you can repurpose the various SG and XG firewall appliances for all kinds of uses. You can run Sophos UTM (of course), boot Linux or UNIX and make it into a server, or even install a different firewall on it (e.g., Pfsense). ... but I digress…

Hello all, I looked under Logging & Reporting, along with RED Management, and I can't find a count of data usage. Ultimately, I'm looking for how much data our remote sites with REDs are using, as they're configured for Standard/Unified.

Hi, I want to use a SD-RED20 behind an UTM with UTM 9.711-5 to connect a small office to headquarter. The connection from the SD-RED20 is established and working fine, for the local networks (few VLANs, split with a aruba, because the SD-20 can…

Hello, I try to setup a brand new SD-RED-60 but facing endless error leds loop. On local site (192.168.1.0/24), Sophos SG125 configuration : On distant site (192.168.0.0/24), the RED-60 boots the following sequence : - System led blinking green…

Hello all, Am I missing something simple, as no matter which of the 5 REDs we have, any client behind them can't connect to the FTP server (port 21) on the main subnet. I've tried several FTP programs (currently favouring WINscp) and they all "time…

Hello all, Presently we have 5 small remote offices running REDs on Standard/Unified configs, so that everything is filtered via the UTM here at HQ. At HQ we have a PBX with approx 35 VOIP phones on it and is capable of handling another 50, easily.…

Is there a comparison between Sophos RED, Cisco Meraki and Fortinet Fortigate? Pros and cons, for example.

Hi Community, we have a UTM that has 35 red tunnels connected (configuration: all split tunnel) , each red has 10-20 clients to handle, most of them connected simultaneously. Since a few days the tunnels are randomly dropping packages, they don't even…

Hi, I did a vulnerability scan of my external IP and in the results I can see that SSL3.0 TLS1.1 and TLS1.1 are still supported for Port 3400. I guess this was already asked before but I didn't find it in the forum. Is there already a solution for…

Hello Hope to get some advice from this great community, as this problem is driving me crazy Our specs: ASG Software, Firmware version: 9.705-3, runing on a VMWare ESXi 6.0U3 We have like 50 RED devices, models 10/15/15w/20, most of them in Standard…

Hallo zusammen, ich versuche gerade eine SD-RED 20 an die Sopos XG 210 anzubinden. In den Systemdiensten habe ich die RED eingeschalten und die benötigten Daten eingegeben. Unter den Schnittstellen habe ich eine neue RED-Schnittstelle angelegt.…

Hi i just had a problem with my RED device i want to share. The same problem with AP. I tried to connect the RED device with my firewall but faild. With another firewall it worked fine. RED LED error code was No configuration available or firmware update…

After I set up a RED20, I plugged an AP into it, as I wanted to have an AP behind the RED20. I have it in Split-Tunnel Mode. The issue I had was that the AP would not show up in the list of new APs to authorize, on the UTM side. I read many many posts…

Hello, I am wondering if someone may have some good ideas here, We are using the RED 50 for site to site VPN on our corporate level. But we also have to run PFSence VPN to connect to all field equipment that we work with. Today I have to use 2…

If I have to connect 1000 remote points with RED devices, which UTM do I have to choose? Or if the answer is a Virtual UTM, wich configuration do I need? Thanks UTM is going to provide access only to the RED devices, no more functionalities.

Hi Guys, will using a mac blacklist block complete Network/Internet access when the Red is in standard/split? Best regards neo

We use UTM2UTM red tunnels for many years and they are working very well. Recently our datacenters have upgraded to multi-homing and with multiple external transfer nets (one for each provider) we would like to have some fail-overs for the RED tunnels…

Hi, i have a question. I have a Sophos SG210 an did set up RED50 in standard/split mode. Port mode: Switch Behind the RED50 is an AP55 with 3 wireless LAN (the same which i have @ the SG210) i am able to access all 3 WLAN and use the internet…

So I want to filter on client side so only sophos reds can use the internet.. what ip or port I need to whitelist? so far I only allow UTM ip but reds status still down.. I want to add sophos.com and supportaccess.. but their ip is dynamic (change all…

Hello Community I have a little routing problem I don't really understand. The Route should be like that Please dont ask why or tell me to directly connect the UTMs. Thats out of the question in this scenario: For this example lets say (IF …

Hallo, gibt es ein bekanntes Problem mit der RED 10 v3 und UTM 9.510-5? Ich habe schon so viele Up2date Zyklen inkl. Firmware Updates angeschlossener REDs oder APs erfolgreich durchgeführt. Dieses Mal hat die RED 10 sich in einen Bootloop verabschiedet…

Is it possible to do the following: We have got a lab-environment in our datacenter. We installed a Sophos UTM and defined multiple VLANS which are attached to the VMs on our Hyper-V-Host. In our remote-office is a Sophos RED15W, connected via RED-Connection…