Hi, we are using SOPHOS-XGS-3300 now we have 2 internet lease line connection we are planning to add one more lease line any issue we will faced if we add more than 2 . TATA-500MBPS ACT-300MBPS after upgrade ILL TATA-1GBPS ACT-300MBPS JIO…

Hi there. I'm trying to deploy this XG330 into my home network with 10G expansion card for WAN and LAN (3gbps fiber internet). If I test through the modem I get 3.2Gbps in and out. If I put traffic through the XG330 I get initially 700mbps then…

Hi, I have XG230 it shows that the wan port is down (Status is Red) however the connection is up. Appreciate any comments

Hi, In doc.sophos.com/.../index.html i found that a bridge interface can configure from 2 to 64 interfaces, but i don't find how many bridges can i configure. Does anyone know the limit?

Hi. Does anyone know if it's possible to exclude configured network interfaces from the coloured interface status icon on the home page of the firewall? Its purpose is to show at a glance of connectivity problems. However, sometimes it is normal for an…

Wan Port Automatic down of sophos xgs 2100 firewall. what is solution.

So, I have Port2 and 4 as WAN interfaces. Port 2 is the main interface with multiple public IP addresses assigned to number of services. Life was going just fine until month ago when one public IP address stop working! You can't ping it from outside the…

Hi All, Working on XG115. Had a complaint that VPN not working for one user, no connect. On investigation i discovered that an old WAN private IP that was changed to public is showing up in tracert to workstations/servers from those who can connect…

We are adding Verizon boxes for failover port 3 static ip from ISP port2 Verizon DHCP, when I tested the failover today, the internet remained at the site, but i was not able to manage it from there portal. Has anyone else had experience with this?

Hi all, I am trying to change from SG210 to XGS2100. In the SG210 there is a section "interfaces > Additional Addresses", that lists each of our IP addresses from the WAN block. As I have some other devices, I am able to turn the interface off for…

From time to time, disabling an interface would be very useful in troubleshooting an issue. Why is there no ability to disable an interface. I've had calls with SOPHOS Engineers who also wished this would be possible for troubleshooting. Engineers at…

Hello, we are trying to get the Sophos Firewall (19.5-MR3) up and running in a public datacenter and to do this we need to change the assignment of zones to interfaces and statically configure the public IP address for the WAN interface. Since the admin…

Hello, I still try to preconfigure the XGS for migration from SG. L2TP, IPSEC-VPN with RADIUS and AD-auth is working. IPSEC tunnel to our branch is fine. Now I want to preconfigure all public IPs and their DNAT/SNAT rules. Actually I am stuck…

I need to support to configure a network. I have one ISP connection. ISP Provide us one primary IP, One secondary IP, One Data link IP and one Public IP. Now I need to configure our firewall before the router. p2p primary ip: 10.255.191.149/30 p2p…

We are considering purchasing a Sophos XGS 116W for a new location. We want to use the firewall to protect 2 network segments and a wireless network segment. We do not want any of these three networks segments to be able to see the other segments…

Hi all, I need to know how to configure my sophos xg with modem , but this modem is in router mode not on bridge, because ISP didn't allow me to make the modem in bridge mode. I have fixed ip public and i never did this configuration ( FW XG <---…

Hi all, We will replace our ADSL connection by fiber connection So we have Echolife Echolife HG8245H5 /GPON Terminal I need to know how to configure XG Wan port with this " FTTH Modem", i don't know if this terminal is layer 2 or layer 3, or if…

Hi, is there an VDSL-Module supporting 250 MBit (from Sophos)? Should be VDSL2-profile 35b .. Thanks,

Hi, When I create a Tunnel interface, I am unable to find the xfrm interface in Network >> Interfaces. I can see the xfrm interface in the CLI though. How do I get to see it in the GUI as I need to use it in a Static Route?

Hello I have two sophos connect together. Sophos1 - switch - Sophos2 I have multiple VLANS between them. All vlans have owen subnet. Phisical interface has also owen subnet. I cant ping betwen vlan interface. Whatever i use. But Phisical interface…

I've got our XG firewall set up for 3 WAN connections as we are in quite a rural area and internet connectivity can be spotty. I have the primary connection, which is a wireless system up to 100mbit up and down. I have a secondary connection which…

I am using my Sophos XG135 as a DHCP server and configured in gateway mode, Running firmware version SFOS 18.5.2 MR-2-Build380. Internet connection is only active for a period of a bout 20 minutes and then it is lost but the WAN interface shows it is…

Hi Community. So I have 2 questions. Both overlap, so answering one may do the other. I have a client with a Cellular WAN as their only WAN connection. 1. How do I expose the User Portal via the Cellular WAN connection? The internal IP and external…

I have a small ICMS network to deploy. There are several VLANs involved. Devices in some VLANs are to be allowed talking to devices in other VLANs, but not all devices are allowed to talk to all other devices. I am expecting all routing to be done by…

Hello Will changing from NAT to Bridge Mode erase all FW rules?