Hi!
Here in my company we have 4 address with Sophos Firewalls and in each Office we do have multiple internet links.
We need to remotely monitor the individual gateway status from each firewall.
Even on the version 20, Sophos offer the option to…
We get notify mails from our customer XGS 116 with SFOS 20 that mails are quarantined due to a detected virus (Malware 'Troj/MSIL-SSP,CXmail/MalPE-BP' detected and blocked) When looking at the device, I can't see any hint at the dashboard that a mail…
Migrated from SG to XG AP's get IP from Windows DHCP. Within packetcapture and Diagnostice/Connection list, i see the connection from AP-IP to 1.2.3.4 port 2712 But no AP's in Firewall - GUI APX320 Ideas?
So i know this topic has been discussed before but no one puts in a complete answer so going to ask it again.
After enabling Exchang enhanced protection OWA externall breaks. I know this is due to the SSL offloading as this is mentioned in several posts…
Hello,
I'm trying to configure SMTP on Sophos Firewall ( SFOS 20.0.0 GA-Build222) : everything is running smoothly in IPv4, but Firewall is blocking outgoing IPv6 SMTP traffic :
I tried to define all kinds of (IPv6) rules to allow this traffic…
Hello World,
I am back testing Sophos firewalls. I am running SFVH (SFOS 20.0.0 GA-Build222)
I have everything working sort of. I setup a hotspot in my lab and everything works fine until I switch from Use the IP address of the first internal interface…
Hello Community,
I have been trying to update Sophos Firewall from v19.5 MR3 to v20 GA, and it fails.
Through the Firmware page, I:
- Download the firmware, shows success.
- Install it, shows success applying it.
- On device reboot, v19…
Hi,
I'm running SFOS 20.0.0 GA-Build222 with two internet Gateways.
Basic load balancing seems to be working ok. Now since one link has a much higher bandwidth but also higher latency than the other I would like to send all traffic of Application…
Hello!
I'm trying to setup a Web Server Protection Rule for my home automation system. I have a lot of other WAF rules which work perfectly.
I'm only having trouble with this one rule, where I get the following error:
I just can't get this rule…
I;m following the few videos that I can find about how to set up Entra AD SSO for captive portal and VPN but I can't seem to get it working. Are there any step by step instructions that I can follow, other than the published Sophos videos, which seem…
Hello, I am using two XGS126 in HA. Firmware version is 20.0.0 GA-Build222 but the same applies to previous 19.5.3 MR-3-Build652.
I am configuring a remote syslog server. Everything works as expected with UDP protocol, the receiver is a rsyslog service…
I'm trying to figure out how the web proxy works.
I configured a browser to use SFOSv20-IP:3128
I only want web access through the proxy, no proxy configured, no access.
I've followed the example, with Web policy "Allow All" and Destination…
Hi everyone,
got a quick one.
Tried to upgrade my XG106 to 20.0, but the firmware doesn't show under "updates".
Running on 19.5.1 MR1 278 which should be a valid upgrade path following the release notes.
Do I need to install 19.5.3 as a step in…
Hi,
for some reason every SSL VPN client is quite randomly disconnected from the SSL VPN server (Sophos XGS87w): sometimes after only a few minutes, mostly between 15 and 20 minutes. Running a ping from the client side to a machine in the server network…
I have to seperate two networks using the same LAN Interface running XG in natest version with 1 phyiscal NIC bound to LAN and 1 physical nic bound to wan. The need is that there is no access form Private Network IPs to Company Network IPs and Vice Versa…
Hello,
I have trouble configuring WAF rule for one specific web server/service
When I try to access service from inside on my pc I get 403
[Sun Jan 07 19:40:08.983664 2024] [authz_core:error] [pid 22769:tid 140041007253248] [client 10.2.1.10:52039…
Hi all, my setup at home is the following.
I have a proxmox host on which I have created an active/passive HA installation of SFOS v20. HA is connected and all green. When I try to register this installation to Sophos central, only the active peer is…
Hello,
Two XGS3300 in an working Active/Passive Cluster, not working after the update to 20.0.
I deleted the Cluster and tried to re-establish it but it fails all the time.
I tried several times with Quick HA or Interactive Mode.
Tried with VLAN…
Quick question:
Do you have to have Sophos Hardware to make VLAN work in the firewall software? I'm using a mini pc running Sophos Firewall V20 and it appears when I set up a VLAN, it doesn't work. Followed the directions on how to create a VLAN but…
Hi community,
I would like to configure my Sophos firewall with IPv6 WAN and LAN. My ISP has provided me with the addresses for this, and I have had a go at getting this to work but with no luck so wondering if someone can help me please.
I am using…
I've seen posts in this forum saying that the Interfaces page in the GUI has a "Renew" button, which can be used for the WAN interface to obtain a new IP address via DHCP.
Where is this "Renew" button located?
I checked the Interfaces page and the…
Long-time Sophos Firewall Home Edition user, running v20 without issue.
PROBLEM arises while replacing my aging SATA SSD with an M.2 nVME drive ...
Downloaded v20 .ISO, burned to disc
Disconnect old SATA SSD, install new M.2 nVME
Boot from…