Hello everyone I am struggeling with the following: The customer has microtik router that connects via wireguard VPN to a remote Windows Server in a Datacentre. The Microtik router is the VPN Client, the Windows Server is the VPN Server. The employees…

This isn´t really a question but rather some strange behavior I ran into when updating a customer´s RED-Devices from v3.0.008 to v3.0.009. Environment: - Sophos XG2300 running SFOS 20.0.0 GA-Build222 - Multiple RED20 and RED60 Devices (6 total)…

When I add a startic route, I lose connectivity to devices connected on the other side of the site to site vpn yet the connection status of the vpn remains connected

Hello guys Fiber Interlink Network 1 should be able to communicate to network 2 through the fiber link Please assist in configuring

We have recently set up Multicast forwarding between our main office and a remote location via a site-to-site vpn. The Multicast forwarding is working from the remote location back to the main office, however, the system we need to multicast in the…

I have an XG appliance in OVH. Since OVH uses a gateway on a remote subnet, I created a new zone, and assigned PortB to that zone with a /64 IPv6 address. The gateway is added using a static route ::/0 to PortB in reality, the default gateway…

I am very confused why this isn't working on the Sophos XG but is working if I make a static route on a Windows 10 PC. The below is what I'm trying to accomplish and what the IP and subnets are that are involved. Any assistance in how to accomplish this…

Hello I've got a strange behaviour when upgrading to SFOS 19.5.1 MR-1-Build278 from 19.0.2 MR-2-Build472. (XGS107) Both of my static routes are not available after upgrade and can't be reestablished. In Version tree 19.0.x everything is fine,…

Hie Guys, so im try to configure failover using ospf and a static route that uses a different link . so ospf works fine, when the destination network is not reachable the route is removed etc. but when i configure the static route with an administrative…

Hi. I use a XG with 19.5.1 MR-1-Build278 Firmware.I have a strange behavior. Today, we can't ping our servers located at a "site to site vpn" branch office. By now, all I can tell is, that the specific static route gets ignored. I see it on the web…

Hello there, When i have the static IP Address disabled in my SSL Global Config it works fine, the firewall can reach all the devices connected through VPN. The issue comes when I enable the Static IP Address in SSL VPN Global Config, When I assign…

Hi There, i started today with the XG on virtual environment (ESXi7). I set up a statc route for external additional Network using by a health service. I add an rule who allows to forward the traffic to this specific network via an internal router…

Hi, How do I choose a VPN tunnel as a next hop in Static routing? The VPNs don't show up in the interface list here- I have multiple VPNs terminating on the same external IP/interface, and I want traffic from one VPN to route to another VPN…

Hey there, My DHCP IP address from my carrier is 203.xx.xx.xx/16 but the gateway is in a different subnet 100.xx.xx.01.. wacky system, but not one I was really expecting.. The issue I'm running in to is that I'm trying to establish a backup IPSec…

XG210 (SFOS 19.0.1 MR-1-Build365) Hello, I have to create a lot of static routes and would like to do this via SSH. When I create a static route via "ip route add 10.xxx.xxx.xxx/24 via 10.xxx.xxx.xxx" it is clearly visible in the overview "route…

Hi Team I am configured Static Routing with 1 VLAN But in my network, there are 12 VLAN are available Do I need to create 12 VLAN IPs in Static Routing ?

We have two wan links connected on sophos & want autofailover between them, for one wan link we have configured bgp and for other wan link we have configured static routes. Now we want bgp routes to be preferred over static routes & in case of link failure…

I tell you that during the migration of a Fortinet FW to Sophos, we have some doubts about the routing issue. Example: Routing to Migrate Destination IP/Mask 172.17.0.0/255.255.0.0 Device: VPN-Gto (This is a Site to Site tunnel, however, even putting…

Hi Sophos Community, I am struggling to route traffic between two sophos over the Point to Point Connectivity as i am deploying my project in Eve Simulator but its not routing the traffic from the 10.10.0.5 PC towards the 192.168.3.30 Win Server and…

Why does the XG210, for the purposes of configuring a static route, require a different Gateway IP address from the VLAN Interface IP address? Trying to get my head around to understanding this static routing thingy on the XG210.

Hi, I have VLAN and for that I have configured Static Routes. Is that I can configure ARP Proxy instead of Static Routes. Manish

Hi, I have configured VLANs so for that I have configured static routes. Now as I am gaining knowledge I thought to configure Route Aggregation / Super netting instead of Static Routes. Is it possible to configure and if yes how ? Can anyone advise…

Hi. Many thanks for reading this, I am hoping someone may be able to throw some light on what I am trying to achive. I am new to the Sophos XG platform but I assume what I am trying to do is possible. Here is my scenario. Two companies in the same…

How do i Configure static routes to below IPs with next hop 100.100.100.6? 83.111.145.225 83.111.145.226 94.57.104.1 94.57.104.2 94.57.104.3 94.57.104.4 94.57.104.5 94.57.104.6 94.57.104.7

Im trying to setup failover connections so that in the event of our WAN (P2P) connection fails the sophos auto fails over to our WAN (VPN) connection. the wan P2P connection also has static routes enabled so these would need to failover aswell.