Good day everyone.
I need to configure something on my XGS136 and can't seem to get it down.
I have a 1gb/1gb fiber coming into a vendor device currently. I am going to move it to PORT4 of my Sophos using a public IP, and then need to share it back…
Hello,
I am using the Sophos Firwall behind a FritzBox in my Home Office. The instaleld Firmware is the latest SFOS 19.5.1 MR-1-Build278.
I have configured a LAN Bridge br01 for all devices behind the firewall.
Now I wanted to be able to add some…
Hey,
I am stuck with removing an interface from br0 on XG115w (SFOS 19.5.0 GA-Build197)
I was trying to remove one interface from br0 and apply changes. Now I can not edit any details of the br0, the UI stuck in an infinite load cycle when I open…
I have implemented my sophos firewall in bridge mode.
I have access to the internal devices, but I cannot access the Internet, what needs to be done to access the Internet?
I was trying with a firewall rule but it didn't work.
Hello community, during my initial setup I config my Sophos XGS 2100 into bridge mode instead of route mode. Now my question how can I change into route mode without resetting the Sophos to factory default? really appreciate your input.
Thank you…
I have a XGS Firewall in bridge mode behind a Uniif Dream Machine. Sadly the port forwarding rules don't work and i wanted to ask if someone maybe knows why. The XGS is in the 192.168.55.x LAN and the Unifi (my main LAN with all devices) is in the 192…
Hi all,
User Kyle Sexson had this issue a while ago, too, but there’s no solution in his post - so…
I have a set of VLANs running on a bridge interface. This works mostly well, but certain outgoing traffic will show up both on the bridge interface…
I have a Sophos XGS126 and an APX320.
Current Setup
LAN is on Port 1, with a static assignment of 192.168.168.1
LAN offers DHCP from 192.168.168.100 to 192.168.168.200
APX is on the PoE port, Port 11 with a static assignment of 192.168.166.1…
A client has a number of firewalls and 2 AD servers, one on prem and one in Azure. They wish to control IP address assignments in Windows instead of on each firewall. This makes sense as using Central to manage a number of firewalls is slow and somewhat…
We need to pass one of WAN IPs to another device (Cisco) across Sophos (HA) .
Others WAN IP are NATed to LAN port withot problem.
This device (Cisco) must have this WAN IP configured on his interface.
We have no acces to the Cisco device).
How…
Hi all,
setup is router -> Firewall -> Ubiquity dream machine.
XGS2100 is configured in gateway mode (need to use SSL VPN), wan cable to port2, lan cable to (F1), lan cable is connected to an Ubiquity Dream Machine PRO.
In the F1port there…
Can we combine two interfaces of the firewall and assign them a single IP.
I need to connect my Sophos to an existing network in such a way that both the combined ports must extend network on both ends.
eg : I have a network in 192.168.0.0/16.
now…
Hi,
I have an XGS107w that I am configuring and i'm having trouble getting clients to communicate from wifi to hard wired clients.
I have Port 1 and the wifi network connected via a bridge interface
I have two clients connected, one is…
Hey all,
I have a Sophos XG connected to an LTE mc801a router in bridge mode. Every night the mc801a is scheduled to reboot, however Sophos doesn't pick up the new DHCP IP address.
If I change the interface to static, and then back to DHCP, it picks…
Hello Sophos Community,
we have to Layers of Firewalling 2 FortiGates installed in HA AP, and 2 Sophos XGS 3300 installed in AH AP.
We want to connect the Two Layers of Firewalls directly using Full Mesh Connected Topology (The figure in the attachement…
We'd like to deploy an XGS 126 to a field location, and to avoid the need of sending an additional 'access layer' switch, I'd like to configure multiple ports to participate in the same vLAN.
I know how to do this on a switch (HP) without thinking about…
Remote STAS in bridge mode
Hello guys.
I'm approving an environment where we have sophos in bridge mode.
The following scenario being evaluated.
Office:
router <-> sophos fw(l2) <-> switches
Inside this office we have an AD with STAS, running…
Hi - I have a Sophos XG 135 and I have set up two different networks with different Gateway IP addresses.
Port 1 uses 192.168.1.1
Port 8 uses 10.150.121.1
Port 2 is the WAN port
I would like devices associated with Port 1 to be able to communicate…
Hi,
I thought creating a Bridge on XGS-136, for example, creates a "switch" between bridged ports, but either I do not understand principle, or reality does not follow the principle - I found no, bridged ports do not behave like switched ports.
For…
Firewall newbee here.
I currently have XG ver 19 configured in bridge mode and working for the most part with the Fios router. All wired traffic is working correctly, However the Wifi connections to the Fios router are not being forwarded or Routed…
Have a 3rd party hardware running XG 19 on. It has 6 ports, using one for WAN and the rest (5) are set in a bridged LAN mode following the directions here: https://docs.sophos.com/nsg/sophos-firewall/19.0/Help/en-us/webhelp/onlinehelp/AdministratorHelp…
hi,
i'm running a XG210 (SFOS 18.5.3 MR-3-Build408) and have it set-up with a bridge pair BR0 for the primary LAN using Port1 and Port4 as physical members. Both are set as LAN-interfaces.
everyting is connected to Port1, port 4 i only use to connect…
Hey guys,
Since Monday morning (7:26 AM), Xfinity was "doing some work to upgrade your services" in my apartment complex. I have two XG home editions, running on different hardware, that are able to initially connect once putting the Xfinity gateway…
Hi all,
Am asking this question for the second time. I am new to Sophos and am finding it nagging that I can't get the basic functionality without doing a lot.
I am setting up a new firewall. By default, a bridge-pair (br0) was created, with Port…