I have a problem with SD RED 20. In XG210 for RED interface after boot new SD RED, i have this: Couldn't update the firmware. Reset the RED to factory configuration. If the error persists, contact support.

Hi All. I'm using XG (ver 18) and currently have a few RED15's setup and working fine. Just had a new SD-RED60 and I cant get it to connect up, do you set it up in the same way as you would a RED15 or different as its as SD-RED 60 ? On the device…

Hi, I can't remove the RED device my sophos XG device. On System services, RED menu; when i want to turn on red status i get error like below I wanted to delete and re-add the red device on the device.

Hi, I have an email alert saying that my RED was down. Its a RED 20 connected to my XG 125w Firewall running the latest v19 firmware. I thought it would just show as down when logged into my firewall and viewing the RED interfaces but its actually…

Why VPN and RED dont work when date is not current in both server and client?

Hi, I tested Sophos XG Home and also XG trial (client and server both software VMs), but with both RED tunnel dont work. No L2, no VLANS, only L3. I have also hardware XG86. When I use XG86 as server and XG Home (software) as client, all works …

I'm having an issue getting the Site-To-Site Red working. I have it all setup and it shows connected but I can't access the remote network. I can ping the remote gateway but nothing past that. Below are my settings for the Red Server.... RED IP: 192…

Reference: Sophos Firewall: OSPF over RED KB-000038170 Jun 17, 2020 Our general setup: We have one HO (XGS v18.5.3) and two BO's (XGS v18.5.2). All three XGS have two WAN interfaces connected with 2 different ISP's. I'll name them "T" and "P". ISP T…

Hi, I configured a RED tunnel between two XGs according to instructions from Sophos. 1.RED tunnel configured 2.LAN2LAN rule created. 3.Routing between LANs set up via RED tunnel. RED TUNEL is active and work fine But I have the problem that…

Updated 2 routers that have RED 15 devices attached. Updated to the latest firmware. Both Red Devices are now on 1 minute connect/disconnect loops. 4 hours on phone support with Sophos to get no answers. Anyone else experiencing this? I now have…

How can I enable a WiFi module in a RED20 that has been configured in XG without WiFi? This has been asked here but I do not find a solution there. https://community.sophos.com/sophos-xg-firewall/f/discussions/124305/red-20-devices-initially-added…

Hi, Trying to get my RED to passthrough a local VLAN but doesn't seem to be working. Having the RED in switchport mode SWITCH obviously doesn't pass it through, however local network works perfectly. However when i change the RED to switchport mode…

I'm trying to configure a remote office (5-10 users) using either an SD-RED60 or Sophos SD-WAN using a second XG Firewall. I don't want to have to make a separate subnet for the few users (I'd have to change a bunch of other routing if I did so), so I…

Hello good Morning a question friends is the sophos XGS 116w compatible with the XG230 firewall? is it the same as a RED15w in terms of configuration? as I have several of these added to my XG230 it is added just like the RED one, I need it to create…

We have the following scenario: Sophos XG135 (SFOS 18.5.2 MR-2-Build380) Port 1 gateway to fibre internet Port 2 Gateway to VDSL Port 3 Gateway to LTE Port 4 LAN Clients Port 5 LAN Server Port 6 DMZ The XG connects multible IPSEC tunnels via Port…

Has anyone done one of these before successfully? I've had no problem with any of the Standard mode configurations, however this Transparent/Split one has given me a headache. I've even got a call open with Sophos and have had a lengthy call today were…

Dears Good Day. I success to establish a new red connection between Sophos x135 ( Server ) and Sophos Xg ( Client ). and routing between two networks is working very well. but I have a problem if the red connection status is down. I have to…

We have a remote employee utilizing wireless internet provided by their landlord. We would like to procure a wireless to ethernet bridge for the wired DHCP handoff to a RED 20. I am seeing some Cisco WET devices that could fit the bill. Has anyone had…

Hi everyone, we created a BO and connected this site with the HO over a RED60 without VLAN tagging. So far so good :-). Now we would like to enroll some AP's in the BO with a setup similar to the HO. In the HO, we make use of Unifi HD nano AP's with…

Hi, What to do? I have a RED20 working correct with Xg Firewall 18.x - when I connect a laptop in LAN port, receive correct IP address through XG DHCP server - can access the remote network I have a Sophos APX320 Wifi access point connected…

I'm running a XG firewall at the office (XG135 18.5.2 MR-2) and one at home (XG135 18.5.2 MR-2), both are connected with RED (Firewall RED client on the XG's). All is working as expected. I just bougth a second hands RED 50 to replace my XG at home…

Hello, I succesfully test a RED device on one XG Firewall, however I want to set same RED Device on a different XG Firewall, I know I have to use the unlock code to do so, and I did it, however when setting and connecting the RED Device I get a error…

I have a 3 site VPN, main & two satellites and the main router is a SG135 I am trying to document the VPN settings however under Configure >> VPN there is nothing listed for IPSec, SSL or L2TP Under Configure >> Network I have two RED interfaces…

I work for a healthcare provider. We are going to provide services for the schools in our county. I need to set up a small network (2-6 devices) inside each of the schools that can communicate with the home office. The school is providing internet via…

Hi Can anyone assist with a link or Documentation on the Recommended Red Device Sizing guide for XGS 3100 & XGS 4300 thank you.