Hello all! I have a Sophos XGS firewall configured with one LAN and two WAN interfaces. The two WAN links are configured in failover mode, the backup link being activated when the primary one goes down. The backup link has limited bandwidth. I need…

Ok so I'm in a bit of an interesting issue and I'm not sure whats going on. Recently we had a power outage that was long enough to draw out the UPS and shut down the network stack ungracefully. Up until then I was able to route between VLANs and even…

I would like to see an easy way to move vlans to another port. This will help in moving a heavily used port from one port to another without having to delete the vlan and DHCP scope and recreate it. This would speed up moving vlans across ports. …

I am newbie currently testing a Sophos XGS 136 Firewall, The basic setup is working. We have a Cisco 3850 Core Switch with 4 VLANS and only the VLAN that the firewall is connected to is working. Traffic from other VLANS is not working and can not ping…

Hi all, is it possible to bridge a Wireless Network to a vlan interface from the firewall itself? The traffic should not leave the RED itself in their lan interfaces. Can this only be done with using separate zone and bridge this separate zone with…

Hi there, We have recently migrated our UTM to an XGS firewall, and are in the process of migrating our Meraki networks to Sophos as well. I am working on our first RED device, and have most things operating but am having trouble with VLAN communication…

Has someone managed to get Sonos devices to work when they are on a different VLAN than the Sonos App? Would be great to share some information. Especially about routing Multicast through the firewall. I found a great article about this matter in…

First, thank you, 2nd, sorry ;-) I just got my XGS4500 setup, very basic default setups. We use Unifi switches, we are migrating from a Meraki. We have all our Wifi working, all the VLANs and whatnot - but our printers (for whatever reason…

Hope someone can help figure out what I am missing. I am pretty sure the issue is on the Sophos XG. I am setting up several VLANS on my Cisco 9500 L3 switch and the issue I am having is I cannot get passed the gateway when trying to access another VLAN…

We were doing DHCP via Windows Server but decided to use Sophos XGS. DHCP to assign VLAN to Polycom phones via OPTION 128 String VLAN-A=20; - NOTE the ; (semicolon) MUST be at the end of the string for it to work with Polycom. XGS will not allow me…

I have 3 VLANS, 1 for CCTV, 1 for wifi controller, and the other for IP phones. data network - port 1 192.168.0.0/24 port1.12 - 192.168.2.0/24 - wifi. (VLAN) port1.13 - 192.168.1.0/24 - CCTV (VLAN) We want to manage the CCTV and the access…

Hello I am trying my head around strange VLAN issues when XG is virtualized. The setup is as follows - ESXi has VLANS created. XG has two ports - Lan and Wan. Lan is on 4095, Wan is on different switch. XG Lan has multiple VLANS created (reflecting…

What is the step to configure SD-RED 20 with VLANs?

hello , I am encountering the following problem: to simplify I have vlan A and vlan B Both have active dhcp server in sophos. Both work normally. However, if I set an ip/mac for a device in vlan A, sophos, vlan B does not deliver any more IP for this…

Hi all, i installed Sophos on hyper-v (vm) with 3 NIC: - NIC-A “LAN” (physical nic on server) - NIC-B “WAN” (physical nic on server) - NIC-C “LAN” (private virtual switch hyper-v) I’ve created Bridge with NIC-A and NIC-C, with "enable routing…

Good day Members, I trust you are well. We are trying to setup a guest Wi-Fi with Sophos and Unifi. We have it currently working but with the DHCP server on the DC, We would like to move the Guest Wi-Fi DHCP to the Sophos XG. Main issue is device are…

XG210, SFOS 19.5.2 MR-2-Build624 So, I have two VLANs, VLAN 70 - 192.168.70.0/28 and VLAN 100 - 10.0.0.0/24. DHCP server is on VLAN100, I want to relay DHCP requests from VLAN70 to VLAN100 for service. I have a relay set up like so: Name …

Hi I am using XG-115 as my firewall and already got number of rules. I also have a couple of VLANs. I followed the below guidance given by Sophos tech support team. The rule works well with individual hosts. but when I replace the individual host…

I have a small problem, I have a mikrotik router set up wlan10 (10.10.10.1/24) on port 2 everything works, I connect directly to the router, I have access to the network via vlan10, and when I connect sophos home (in bridge mode), I have an address assigned…

i have dns domain server 10.0.0.1 mask 255.0.0.0 gateway 10.0.0.2 & and ip range is 10.0.0.1 to 10.0.0.254 but now i want to give different ip range to different department like 10.0.1.1 to 10.0.1.254 to support department and 10.0.2.1 to 10.0.2.254 for…

Hi, Sample: configured sophos XG135 VLAN1 to go through port 1 of the firewall , how do i set it to use port 3 and 4 on switch for VLAN1. VLAN1 goes though port 1 on firewall then port 3 and 4 on the switch connected . Port 1 part is done, how…

Hello, I have the following scenario, I need to transport some VLANs that are on my core switch L3, behind the RED (Appliance), I have already tried to put the Firewall interface marked with the VLANs that I need, in Sophos I grouped the VLANs in a bridge…

I just cannot figure this out now. Been trying this for a day and desperately need your advice on this. I am trying to build a simple separated (isolated) VLAN from Ubiquiti Unifi AP Network to Internet route: Unifi AP -> Unifi Switch -> Sophos XG.…

I have a VLAN, currently on Port1. Now I connected my XGS-126 to my switch using glass fibre. However, under Network/VLAN I cannot edit the Port# Which selection of the configuration should be exported? Would it be sufficient to export just the VLAN…

Hello, I created a VLAN for my WAN interface. I see the IP in my FritzBox but the Gateway in the Sophos XG Home is offline. The ping check under "diagnostic" failed, too. Fritzbox Network Interfaces Gateway