I need to deploy an XG at the new site with a VPN tunnel back to the client's head office, but the remote site does not have a static (or even it's own public) IP address. Traffic goes through a NAT pool at the ISP. With the SG you could configure an…
Hi,
I tried to set up a network connection between a Sophos XG firewall and a Sophos Red.
I follow up the below guides to set up the Red connection:
https://support.sophos.com/support/s/article/KB-000036699?language=en_US
https://community.sophos…
Hello,
hello all. we have been trying to install a sophos red 20 including dhcp for some time now. the red has been configured and also reaches the internal network. However, as soon as a dhcp request is sent from a client behind the RED, this request…
I have a scenario with an SD-RED20 connected to an XG210, through a Split tunnel. The question is whether even though I have a Split Tunnel and in a moment the service of the XG210 device is lost or it just shuts down, does the SD-RED device also lose…
Hello,
We have a PBX inside the network 10.20.0.x and we need to access it from two other different networks (192.168.1.x and 172.14.0.x).
We have two RED15 devices, 192.168.1.1 and 172.14.0.1 so we can connect to the PBX on the 10.20.0.x. Both…
Hi Good Day
it is possible that sophos red can be connected in this network diagram
ISP --> PEPLINK---> SOPHOS XG
note: peplink is not in DROP IN MODE
thank for the help..
Hello, we have a problem with the transmission of the voice on our IP telephones between the XG and the SD-RED 20. The connection can be established (it rings and you can pick up the receiver), but nothing can be heard. The RED is located in the network…
We have a need to allow multiple multicast source devices to have their multicast packets sent across to the branch office through RED device and vice versa. I did a bunch of research but haven't found anything specific to what I am trying to do. Basically…
Hi, we are currently migrating some RED 15w devices from Sophos SG to Sophos XG.
Our setup is follows:
- Each RED Device is in a seperate /28 subnet
- On REDs with split tunnel I configured the magic Wifi IP 1.2.3.4
- A few REDs tunnel all neworks…
Hello,
I have two xg 210 in A/P HA (18mr4) and two branch offices with red60
LocalityA - 2x xg210 HA (ISP 100/100Mbps) FileserverA
- utilization is about 50% during working hours and 10% out of working hours
LocalityB - RED60 (ISP 100/100Mbps…
Hello,
I'm looking to install a Red device to establish a VPN between 2x sites so a NAS at site2 can be accessed by devices at site1. But I still need other devices at site2 connected to the ISP supplied modem to still be able to access the NAS too…
Hello, I have connection between two sites (Head Office and Branch Office) in the HeadOffice i have an XG Firewall connecting to the Branch Office through RED, i can ping the RED from the XG Firewall, but cannot ping the hosts behind the RED. i can also…
Hallo,
mit einer XG 310 sind 2 RED60 und 2 RED50 über Internet verbunden. Die zwei RED60 u. eine RED50 sind mit der XG310 im Bridged-Mode. Die letzten Wochen habe ich täglich das Problem, dass das Netz hinter den beiden RED60 und der RED50 nach einer…
Meine beiden RED Devices verbinden sich nicht mit meiner neuen XG Firewall.
Ich habe meine Firewall getauscht. Die RED Devices angelegt in der neuen und soweit so gut- jedoch verbinden sich die RED nicht mit der Firewall. Was kann ich tun?
Hi,
We have a network connection into a main site via a RED, this is all working fine. On this site we standard VLAN and a VOIP VLAN and ths is configured and we are able to ping all devices and everything is working. The Phone system is in a Datacenter…
Hi,
We are going to change the IP address of our XG Firewall WAN interface to another ISP. My concern is our SOPHOS RED 50 devices which we deployed 25 in our branches. What do i need to do? Do i need to request for new unlocked code because the current…
Before the traffic issue the RED SD 60 was disconnects severla times the morning, only a power off solves this issue
I got a customer with a issue depending thr traffic and connection.
He uses a RED SD 60 and XG Firewall
Typ: XG230
SFOS…
Hi I'm new at Sophos, Basically this is our networking that I'm working I already establish the connection from Sophos Red to Sophos XG. The network behind Sophos Red can ping and access the server behind the Sophos Firewall, But the network behind the…
HELLO RECENTLY I HAVE HAD DETAILS OF SLOW SPEED IN MY DEVICES RED 15W AND RED 50 I HAVE UPDATED TO VERSION 17.5.15 BECAUSE WITH VERSION 18 I HAD DETAILS WITH SOME NAT RULES, MY IPS PROVIDER OFFERS ME ONLY 150 VELO SITE 200MB AND MY OUTPUT THROUGH MY NETWORK…
Can I have my REDs connect to an alias rather that the primary interface address?
I'm failing a PCI compliance scan and some of the REDs I have are on dynamic service. That said, the port 3400 black hole rule will probably come back to haunt me.
I…
Hello,
we did an firmware update on an XG 550 Cluster last weekend.
Initially the RED 50 was running but after a colleague did some changes on another RED 15W it is disconnected now for unknown reasons.This was on Monday around 16:50. Currently the…
I have an XG135 running (SFOS 18.0.1 MR-1-Build396) and I am currently failing Security Metrics PCI scan for the following:
I am trying to follow the KB Sophos has provided but in v18 DNAT and Firewalls are separated, and I can't seem to get everything…
I'm new to Sophos XG and RED, so pardon if the answer to this is buried somewhere in the documentation (I can't find it though). I've established a Red SD-20 tunnel from my home office back to an XG firewall at my primary office. It's my own company …
A few days ago my connection from my REDw devices has become extremely slow I can't even reach 1mb of speed I have the REDW added to a different LAN zone with its own rules
I have the firmware for the XG: SFOS 17.5.14 MR-14-1 AND FOR THE NETWORK: 3…
Hello,
I just re-saved the config of one RED Device without change to be sure, the settings are applied correctly to the device.
In Log viewer I then surprisingly noticed that all other REDs immediately disconnected and reconnected during working…