Hi, Is there anyway to tell if a Flexi Module is installed besides looking at it physically ?

I would like to see an easy way to move vlans to another port. This will help in moving a heavily used port from one port to another without having to delete the vlan and DHCP scope and recreate it. This would speed up moving vlans across ports. …

Hi all, I rarely work with Sophos Firewalls and haven't ever had to do much on them before, but having recently logged in to one I found that on the 'Control Centre' page that 'Interfaces' is highlighted orange. When I then select 'Interfaces' it…

So i'm a bit confused and could use some help. After running NMAP on my public IP for a sanity check i was greeted with ports showing open that shouldn't be available to the WAN port. I don't have any services checked on my local service ACL for WAN Starting…

Dear Sir I have configured two ISP on two different ports of firewall providing the internet facility through Sophos Firewall. I am using the firewall load balancing features by assigning the weightage of 2:1 to both the ISP's. But load balancing feature…

Dear community members! We are planning to insert an XGS firewall into our existing network infrastructure with multiple WANs. This is the current setup: Three WAN routers from different ISPs with fixed public IPs are connected to a multi-WAN router…

Hello, Can I have PIM-SM and IGMP on a interface in the same time? I have a problem with IGMP on interface with active PIM-SM neighbour (pim-sm router). In the presence of a PIM-SM neighbour, IGMP is inoperable for another destination. Is this behavior…

Hi, we have sophos xg-210 one LAN port utilization is high i have attached monitoring tools screenshot please check. model-XG210 Thanks satya

XGS136/SFOS 19.5.2 Is it possible to use an alias WAN IP other than the firewall's IP with the SSL VPN? I'm setting up the XGS to replace an existing production firewall, and using an unused LAN and WAN IP to do it. My plan is that on migration day…

Hey Team, One of my end customer having issue in FW while upgraded SFOS 19.5.1 --> SFP ports/interfaces couldn't respond or stopped working and ethernet ports are working fine. XGS3100 (SFOS 19.5.1 MR-1-Build278) Expecting usual support from my…

Hi all, Is there a possibility to install a Flexi port module to an existing HA Pair without switching off both firewalls at the same time ?

Hi All, I recently added IPv6 support to XG FW and something says not right. I have pubic v6 address on WAN link, 2 private ranges on LAN and DMZ . I am using router advertisement for IPv6. The FW rules show traffic on v6 both directions, The v6 test…

Hi everybody! Now we have a second WAN link (DHCP) and I‘m following the instructions: https://doc.sophos.com/nsg/sophos-firewall/18.5/Help/en-us/webhelp/onlinehelp/AdministratorHelp/Routing/Gateways/RoutingConfigureGatewayBalancing/index.html …

Good day everyone. I need to configure something on my XGS136 and can't seem to get it down. I have a 1gb/1gb fiber coming into a vendor device currently. I am going to move it to PORT4 of my Sophos using a public IP, and then need to share it back…

I have a Sophos XG 125 Firewall and recently after updating the latest firmware, I'm having an issue with WAN port of firewall. The firewall's WAN port does not update the IP address automatically. I have to unbind the port and bind the port again to…

During HA-Rebuild and Upgrade to 19.5.1 I noticed a log in System logs: "PortA4 up" on the peer node at a time when it was unexpected. I then noticed on the physical interface, that the LED of that Port were off while the other 3 were blinking. It…

Hello, I created a VLAN for my WAN interface. I see the IP in my FritzBox but the Gateway in the Sophos XG Home is offline. The ping check under "diagnostic" failed, too. Fritzbox Network Interfaces Gateway

Hi! I have Sophos XG106 rev.1 with home license activated SFVH (SFOS 19.5.1 MR-1-Build278) . Every few days the gateway/wan port goes down, attached log bellow: -- cd /log tail -f dgd.log NOTICE Mar 17 09:45:33Z [5495]: Executing : <gateway…

Hi there, I have one question related on the DSL Module , we configured everything like it should be - the connection works fine. But we have a small issue, that it shows the interface under Control Panel / System always as down. I remember something…

In preparation for a Network upgrade (which we are also re-subnetting the entire network) I'd like to connect our new core to our XG 550 on a newly installed 10G port on a separate subnet. The existing is on a 1G 10.10.x.x /24 the new will be on 10.16…

WAN interface keeps going down every one /two Hours or so days. It started earlier this week and I can't find a reason why it happens. Once I reboot the router, it comes back up.

Hi all! Quick question regarding XGS 126: MTU is a property of the physical interface. If I want to reduce the MTU for a VLAN I have to do it on the physical interface. By adjusting MTU value I seem to lose the VLAN interface and the associated dependencies…

Hi, I would like to remove an interface of a LAG (HA AP Setup with 2 Nodes, XG310 (SFOS 19.5.0 ). I removed port8, clicked save, then the XG rebooted and the 2nd node became active. There the interface was still present. A renewed reboot back to node…

Hey, I am stuck with removing an interface from br0 on XG115w (SFOS 19.5.0 GA-Build197) I was trying to remove one interface from br0 and apply changes. Now I can not edit any details of the br0, the UI stuck in an infinite load cycle when I open…

Hi Community, is there a way to trigger a poe power cycle on poe ports on xgs firewalls. This would be very helpful to reboot a poe device remotely. Thank you. Kind regards, Chris