HI How can i check the interface counters for WAN interfaces in the Sophos firewall ?

Hi, what would be the proper way to configure different WAN ALIASES for outbound traffic, for example in this manner: LAN users would use WAN Alias 1 for browsing and accessing web LAN2 users would use WAN Alias 2 FreeWiFi users would use WAN…

Hi everyone, I am using a Huawei 3372 LTE stick on my SG-125 with SFOS for a couple years now. It is configured in DHCP mode as a failover WAN connection when the main connection goes down. Up until now this worked as intended but after upgrading the…

Looking at IP Hosts like #Port2 or ##ALL_RW, they are dynamic IP addresses, correct? So if Port2 is my WAN port and the ISP changes my IP (via DHCP), wherever #Port2 is used in any rule will automatically be updated instantly so that the rule still applies…

Hello: I have a WAN port (Port 2) that is connected to our ISP with an IP block of 65.170.xxx.xxx/29. We have another block of IP addresses from the same provider at 63.162.xxx.xxx/29. Both come in thru the same ISP router (Cisco 4300). There are 4…

Hi all, can someone provide a hint, how to access a device where all LAN-Interfaces are "tagged" and "LAG"-ports? I've restored a migrated config and now the only untagged port is the WAN-port (can#t ping or access these port) I am able to access…

Hello, I try@home to migrate from UTM zu SFOS. On the good old UTM there was only one LAN Interface. This was the gateway for some PCs. At the network configuration on the UTM, I configured the real-router-getway as gateway in this one UTM NIC. It…

Hello Community, I am currently in Poland setting up a second S2S tunnel and I am struggling with the fact that the xfrm interface of the tunnel cannot be found under the interface to which the tunnel is bound. What am I doing wrong? Attached are some…

Hi all, any hints to configure mobile WAN as backup line? wired WAN is default but when line is down mobile WAN should jump in place. Mobile WAN must be turned on or not? WWAN Interface must be to automatic or manual? Thanks for help …

Hi, Is there a limit to the number of IP aliases per interface?

I need some help to understand why this firewalls IPv6 gateway is constantly reported as failed. It's XGS126 with SFOS 20.0.1 Because of that Gateway errors I reconfigured it from being an active gateway to a backup failover gateway only. I have…

Brief description of my setup: WAN1 is a hardline connection. WAN2 is a cellular 5G connection, using a standalone antenna and modem. SD-WAN 1 is configured for general internet traffic, where WAN1 is the default and WAN2 is failover, using TCP…

Hi, I'm using a XGS116 with SFOS 20.0.1 MR-1-Build342. I've got a public subnet 1 (2.1.1.0/30) assigned by the ISP. 2.1.1.1 is their gateway. 2.1.1.2 is used as static IP of PortF1 (ISP1). I've got a backup connection on Port3 (ISP2). I've defined…

Hello, So I have a weird scenario and I need second opinion. We have two firewalls Active Passive and two switched Active Active The first switch was configured to connect to the primary firewall on a port F4 and this port has vlan on it,…

WAs used showing false bandwidth but after upgrading I get this: Anyone else experiencing this ?

Hi all, Is it possible to got interface- & error details for a LACP-connection? Thx Dirk

Hello, I have a situation where my ISP installed a router and gave me a subnet ( 10.1.1.0/24 ) with the gateway being the router(10.1.1.1). My understanding is that I need to configure an internal network (i.e 10.1.2.0/24) on the LAN side of the firewall…

Update to LAG not working unless you specify interface speed Using XGS4500 on 20.0.0 GA-Build22 with XSAZTCHF4 "Sophos FleXi Port Modul 4 port 10GbE SFP+" LACP bonding was not working on PortsA1-A4 unless specifying 10G Interface Speed manually, disabling…

Hi, Can anyone confirm whether Sophos supports /31 subnet config on WAN interfaces please? XG2100 running SFOS 20.0.0 GA-Build222 Thanks

I have recently switched to a new ISP who allows me a blistering 3GB connection of which I wish to take some advantage. To do this, I rebuilt a new firewall from scratch with a 1Gb onboard NIC, plus a 2x10Gb NIC. This gives me 3 ports, which are in order…

Hello Team, We are using the Sophose XG firewall, I would like to raise the concern regarding WAN Ports are not working, can you please help on it

Hi all, Today I have a new problem which dates back more than 3 months to configure the firewall with the Nokia FTTH modem in bridge mode. -Sophos XG86w -FTTH modem Nokia: G-1425G-B The Device is a router with built in GPON ONT - it is for broadband…

Dear All, I have observed a strange behaviour from Sophos XGS3100 firewall. My LAN network is 172.20.52.0/23 network. When I connect the Sophos firewall to my LAN, the Firewall gets an IP 172.20.52.145/23. After that I cannot ping or access the interface…

Customer is installing a new ISP connection but will have the old one for a while as they have WAF to an internal server, and DNS pointing to current ISP PIP. Left Port2 configured as it was. WAN zone, with static IP info. Configured Port3 to be the new…

Hello, I'm kinda new to networking and I'm currently working on a network lab to enhance my understanding of firewall concepts. My setup consists of the following: Virtual Machines: Kali Linux VM (IP: 192. 168. 10. 128) Windows VM (IP: 192. 168…