Dear all, I am facing a problem that my WAN Port always showing RED and i could not ping the WAN Gateway. At the same time, the same line with the same Static ip address is working in my laptop / nearby desktop without any problem. Kindly let…

I'm trying to configure an SSL VPN. Our WAN subnet has 5 IP addresses, with 4 aliases set up for the additional IPs: Port2 Port2:0 Port2:1 Port2:2 Port2:3 Currently, I have a web server running on Port2:0 . I want the SSL VPN to run…

Hi all, I created a new alias interface but missed on digit, so the address doesn´t belong to a existing interface configuration. Now I cant delete that alias because its not showing up in gui. Is there a way do get rid of that alias via console?

HI How can i check the interface counters for WAN interfaces in the Sophos firewall ?

we have reinstalled the firmware for the firewall. and port 1 is not working it was damaged. we are trying to configure port 2 or 3 as LAN via the command line When we try to use interface configuration it is not allowing us to configure port 2 , we…

Bonjour Je dispose d' une double carte intel 10g et utilise le firewall xg en version virtualisée. A l' heure actuelle le débit est bridée a 1g et les paramètres semblent grisés. Est il possible de basculer et forcer zn 10g

Hi, what would be the proper way to configure different WAN ALIASES for outbound traffic, for example in this manner: LAN users would use WAN Alias 1 for browsing and accessing web LAN2 users would use WAN Alias 2 FreeWiFi users would use WAN…

Hi everyone, I am using a Huawei 3372 LTE stick on my SG-125 with SFOS for a couple years now. It is configured in DHCP mode as a failover WAN connection when the main connection goes down. Up until now this worked as intended but after upgrading the…

How do i remove the Physical Ports 5 and 8 in a XG 115 firewall from cli? After a restore of a XG125 backup into the XG115w i have these ports, they should be pseudo ports and editable. But they are not..

Looking at IP Hosts like #Port2 or ##ALL_RW, they are dynamic IP addresses, correct? So if Port2 is my WAN port and the ISP changes my IP (via DHCP), wherever #Port2 is used in any rule will automatically be updated instantly so that the rule still applies…

Hello: I have a WAN port (Port 2) that is connected to our ISP with an IP block of 65.170.xxx.xxx/29. We have another block of IP addresses from the same provider at 63.162.xxx.xxx/29. Both come in thru the same ISP router (Cisco 4300). There are 4…

Hi all, can someone provide a hint, how to access a device where all LAN-Interfaces are "tagged" and "LAG"-ports? I've restored a migrated config and now the only untagged port is the WAN-port (can#t ping or access these port) I am able to access…

Hello, I try@home to migrate from UTM zu SFOS. On the good old UTM there was only one LAN Interface. This was the gateway for some PCs. At the network configuration on the UTM, I configured the real-router-getway as gateway in this one UTM NIC. It…

Hello Community, I am currently in Poland setting up a second S2S tunnel and I am struggling with the fact that the xfrm interface of the tunnel cannot be found under the interface to which the tunnel is bound. What am I doing wrong? Attached are some…

Hi all, any hints to configure mobile WAN as backup line? wired WAN is default but when line is down mobile WAN should jump in place. Mobile WAN must be turned on or not? WWAN Interface must be to automatic or manual? Thanks for help …

Hi, Is there a limit to the number of IP aliases per interface?

I need some help to understand why this firewalls IPv6 gateway is constantly reported as failed. It's XGS126 with SFOS 20.0.1 Because of that Gateway errors I reconfigured it from being an active gateway to a backup failover gateway only. I have…

Hi, I'm currently preparing our new XGS3300 to migrate from our XG310 which is soon end of life. I've done a Config Backup from the XG310 and applied it to the XGS3300 which was successful apart from the XGS3300 MGMT Port is now disabled. Is there…

Brief description of my setup: WAN1 is a hardline connection. WAN2 is a cellular 5G connection, using a standalone antenna and modem. SD-WAN 1 is configured for general internet traffic, where WAN1 is the default and WAN2 is failover, using TCP…

Hi, I'm using a XGS116 with SFOS 20.0.1 MR-1-Build342. I've got a public subnet 1 (2.1.1.0/30) assigned by the ISP. 2.1.1.1 is their gateway. 2.1.1.2 is used as static IP of PortF1 (ISP1). I've got a backup connection on Port3 (ISP2). I've defined…

Hello, So I have a weird scenario and I need second opinion. We have two firewalls Active Passive and two switched Active Active The first switch was configured to connect to the primary firewall on a port F4 and this port has vlan on it,…

We currently have the problem that our customer has an HA configured with two XGS2100 and after a restart / failover test one of the fiber ports remains down and thus the entire network is paralyzed. As soon as I restart the firewall, the Auxiliary Sophos…

WAs used showing false bandwidth but after upgrading I get this: Anyone else experiencing this ?

Hi all, Is it possible to got interface- & error details for a LACP-connection? Thx Dirk

At our main site we have two Sophos XGS3100 in a highly available (active/passive) configuration. At a second site we have a single Sophos XGS 2100. On our Sophos XGS3100 we have a RED interface for a Sophos SD RED60 at a third site in a Standard…