I have noticed this on a XGS136 18.5 MR3, the machine is in HA and when viewing firewall log it is full of invalid traffic logs. When doing tcpdump I can see in GUI that it resolves the out interface as Port10 which is my dedicated HA interface. The…

Hey everyone, i have cyberoam cr25ing device. I installed sw 17.5 version on the device. installation was successful I can make configurations on the interface. But my lan port is not active, the led light is off. Can you help me? thank you

Dears, I have two questions: The first is I need to make a virtual IP for server (give it two IP and appears with one IP ) How to do this with sophos XG? The Second I have an issue with ssl vpn, by applying ssl vpn it's working good with windows…

I have upgraded my Internet to 2Gbps, but currently have a 1Gbps bottle neck at the firewall. I have an XG450. I have 2 SFP ports that I would like to move my LAN/WAN connections to. But I am not sure what all I need to change in order to accomplish this…

xg V19 has been released and until now no wayto turn off an interface button permanently? does it look t hat hard to make it?

Is it possible to have assign another port as the same as my WAN port? Same public IP Address. I'm having challenges to connect Cisco IPSec Site to site (Remote site with CGNAT) to my Sophos with Public, Dynamic IP Address. The idea is if it is possible…

Hi guys, 1 of my customers has a brand new XGS2100 with v19.... when i try to take a speedtest from a pc... all the other pcs goes offline... even my teamviewer goes off... and when the pc finish the speedtest all bacame back online... Even if i…

We have an XG 310 that has two separate internet connections to the same ISP for redundancy and load balancing. Obviously, these two connections are set up on their own WAN ports on the XG, each with a different static IP (and each port has a different…

We are using xg115w v19 Wan connection drops and connect again around every 20-30 minutes and Why I can not save override mss section? thanks

Thank you for what seems an excellent product. I am a newcomer to firewalls (I briefly used the KYZO "Pizzabox" some 10 years ago, but nothing since), and am trying to understand how best to set it up. So far I have it working with the WAN port connected…

Hi * I have a software based Sophos Firewal with 4 Interfaces. This month I changed from DSL to Fibre which allows me to speed up my browsing ;-) Changing WAN connection was not a big deal, but my interface - lying on Port2 - has some trouble by properly…

I am very new to the sophas and I only have some months of experience in setting simple Network . I have experience in configuring the sophas network with two ISP(currently Worldlink and Subisu ) where I set one ISP in port 1 and another ISP in port…

Have a weird issue Port2 (WAN) is up and connected via PPPOE but status shows red as in down. I have rebooted twice already and still shows RED. There is internet. Any ideas?

Hello everyone, I have been trying to set up a PPPoE connection for several days. Unfortunately, the connection is not established despite all the correct settings. I enter login and password, set VDSL for my internet operator, set MTU according to…

Hello, I have 2 WAN port as long both are working everthing is ok. But as soon my 2. Fritzbox is dead (Cable Fritzbox fails like once a year, but thats another story) there is no regular outgoing network anymore. In WAN Manager both are ok, in the…

We purchased two XG750 to run in HA-Active-Passive config. Each is identically equipped with 4 SPF+ ports and 2 QSFP ports. On the Primary XG the SFP+ ports are named PortC1-PortC4, left to right, but on the Auxillary XG the SFP+ ports are name eth0-eth3…

Hello! I have 2 PPPoE WAN connection to each other Sophos appliances If i switch to the passive device manually or if one of the monitored interfaces goes down the pppoe reconnect time is so long, maybe this caused by the ISP modems? I am interested in…

Sanity Check: Cabling dual ISPs into separate VLANs and then plugging each one into the Sophos WAN port. Hey All, How are you doing? I wanted to reach out and ask my fellow network engineers at Sophos for a sanity check on my setup. I have a cluster…

I have a server on interface A with its own zone and a static IPv4. It is not reachable from the LAN zone on interface B, even though I have a firewall rule with logging on top of any other rule that says allow from LAN, Any host to Server_Zone, Any host…

Hi, (First, apologies. If this question makes more sense in the UTM forums I'll start there, but I imagine doing it wrong would cause problems with my XGS too before I even get started.) After many years, and some trepidation, I'm moving from a UTM…

I read in several forum posts that the ability to disable and enable an interface was slated for a v18 feature set, but I do not see it - so I suspect it was not implemented? That would be a pretty big step back to still be missing after 4 years of planned…

Dear community- I have a scenario I would like to achieve with XG330 and a Synology router. Background story: We have a small office setup with a Synology router, that handles our WAN, LAN, Wifi and VPN (IPSec to GCP as well as L2TP for road warriors…

Hello everyone, I am trying to connect two LAN's that I setup on two separate interfaces (Port 1 and Port 5). I also created a new zone for the LAN on port 5 called TEST_LAN. Here are my rules. RULE 1: LAN to TEST LAN Source Zone: LAN …

Hi Can someone help set up Arris and XG firewall? I just got cable internet form Optimum but wish to use my own cable modem. It is Arris TG1672G which I am able to configure fine until I plug in coax form cable company and it gets provider's config…

There was a previous thread around a year ago where Casey Luchsinger was having issues getting a Starlink device working on an XG. The thread showed no resolution. One of our customers has ordered a Starlink service (to our surprise). Has anyone successfully…