Hi, I have a virtual Firewall v17.5 on a dedicated OVH ESXi Server. the WAN gateway is not on the WAN subnet This article explains it quite well community.sophos.com/.../using-xg-on-ovh-dedicated-server---general-routing-issues will it still work…

During HA-Rebuild and Upgrade to 19.5.1 I noticed a log in System logs: "PortA4 up" on the peer node at a time when it was unexpected. I then noticed on the physical interface, that the LED of that Port were off while the other 3 were blinking. It…

I have a Sophos XG 125 Firewall and recently after updating the latest firmware, I'm having an issue with WAN port of firewall. The firewall's WAN port does not update the IP address automatically. I have to unbind the port and bind the port again to…

Hello, I created a VLAN for my WAN interface. I see the IP in my FritzBox but the Gateway in the Sophos XG Home is offline. The ping check under "diagnostic" failed, too. Fritzbox Network Interfaces Gateway

Hi! I have Sophos XG106 rev.1 with home license activated SFVH (SFOS 19.5.1 MR-1-Build278) . Every few days the gateway/wan port goes down, attached log bellow: -- cd /log tail -f dgd.log NOTICE Mar 17 09:45:33Z [5495]: Executing : <gateway…

Hi there, I have one question related on the DSL Module , we configured everything like it should be - the connection works fine. But we have a small issue, that it shows the interface under Control Panel / System always as down. I remember something…

I need to support to configure a network. I have one ISP connection. ISP Provide us one primary IP, One secondary IP, One Data link IP and one Public IP. Now I need to configure our firewall before the router. p2p primary ip: 10.255.191.149/30 p2p…

In preparation for a Network upgrade (which we are also re-subnetting the entire network) I'd like to connect our new core to our XG 550 on a newly installed 10G port on a separate subnet. The existing is on a 1G 10.10.x.x /24 the new will be on 10.16…

WAN interface keeps going down every one /two Hours or so days. It started earlier this week and I can't find a reason why it happens. Once I reboot the router, it comes back up.

Hi all! Quick question regarding XGS 126: MTU is a property of the physical interface. If I want to reduce the MTU for a VLAN I have to do it on the physical interface. By adjusting MTU value I seem to lose the VLAN interface and the associated dependencies…

Hi, I would like to remove an interface of a LAG (HA AP Setup with 2 Nodes, XG310 (SFOS 19.5.0 ). I removed port8, clicked save, then the XG rebooted and the 2nd node became active. There the interface was still present. A renewed reboot back to node…

Hey, I am stuck with removing an interface from br0 on XG115w (SFOS 19.5.0 GA-Build197) I was trying to remove one interface from br0 and apply changes. Now I can not edit any details of the br0, the UI stuck in an infinite load cycle when I open…

Hi, It is possible to connect XGS3300/4300 to core switch with RJ45 SFP+ ASF-10G-T transcievers to get 10Gb/s speed over cooper? Any other transciever option, on link listed below I can only find this option for XG, not for XGS models? Has anyone tried…

Hi Community, is there a way to trigger a poe power cycle on poe ports on xgs firewalls. This would be very helpful to reboot a poe device remotely. Thank you. Kind regards, Chris

LAN LAGG (NON LACP) Active/Back-up Stops working after 5mins. I have to unplug one of the links for it to start working again. Until i unplug one of the links, can't ping the XG, get online and the SOPHOS Wifi stops working..... Basically the LAN…

We are considering purchasing a Sophos XGS 116W for a new location. We want to use the firewall to protect 2 network segments and a wireless network segment. We do not want any of these three networks segments to be able to see the other segments…

We are currently being provided a block of 5 static IP's through our Comcast Fiber EDI connection with Comcast providing us (2) ranges of IP's. We get an L3 range and a Usable range. My understanding of this is to allow easier troubleshooting of the Comcast…

In our production environment we have replaced our old firewall with a Sophos XGS 116. We have replicated the rules we had in our old firewall and everything seems to be going well: our applications are accessible, we can manage our databases... in short…

Hi We have a fibre link from our ISP with a static IP and a secondary / extra range of public IPs. Public IP: 100.100.100.62 (numbers made up) with GW 100.100.100.61 - This is the primary IP we use. We also have a set of secondary public IPs on…

Dear Mate, I've two links one is a static IP address another is a PPPoE connection, both links are ACTIVE connections, whenever a static IP link is down, the PPPoE connection is not working properly, it's very slow but that pppoe link is 400mbps line…

Hello. I have 5 different PPPOE accounts from my ISP .. ISP gave me one fiber modem with Ethernet cable out of it ... I was able to start one PPPoE session without any trouble, but I don't know how to start several sessions on one port. Adding an…

Running SFOS 19.5.0 GA-Build197 How to enable SNMP via WAN port? I have enabled: System > Administration > Device Access > SNMP on WAN and LAN There is no response to SNMP queries from the WAN. However, it works fine in LAN. What else needs to…

Hi all, I need to know how to configure my sophos xg with modem , but this modem is in router mode not on bridge, because ISP didn't allow me to make the modem in bridge mode. I have fixed ip public and i never did this configuration ( FW XG <---…

We have a problem with migrating our configuration from 17.5 > 18.5 The IP which we used to login through the weblogin has changed from 192.168.85.4 to 192.168 .89.10 The topology looks like this [FW-ASA]-[FW-SPHS] | [USER] So there are three interfaces…

Hi, Please, we are on version 19.5 This doesn't make sense... 1,10,12,2,3....