Hi folks, I have the following problem: I have an icinga 2 running in my network and I want it to ping a remote network via S2S. This does work, but as soon as i create a DNAT with HTTP and HTTPS to my icinga, it stops working. What i tried: …

v18 newbie here. in earlier version 17, there was only the firewall rules for all connection types. In 18, have to create nat rules too. There is no usage count on some of my migrated after 2 weeks from upgrade. Lan to lan communication requests…

Attached screenshot from UTM NAT rules. how to configure those nat rule on XG.

Hello all I want to create NAT + Access rules for DNS and NTP so any UDP 53 and UDP 123 traffic targetted for WAN gets redirected to internal servers. Can anyone suggest how that can be achieved? Thanks A

We have some internal servers on which we have configured NAT rules to expose them to internet via dedicated WAN IPs for each server. We are able to connect to the servers from WAN without any issues. But we are unable to connect from one server to…

After updating from SFOS 18.5.3 MR-3-Build408 to SFOS 19.0.0 GA-Build317 I started getting complaints of services not working, they depend either on outbound firewall rules or inbound DNAT rules. The first failure to be reported was VoIP, oddly enough…

The equipment that connects to the top or bottom of the firewall has changed. At this time, the snat or dnat policy set on the device is not applied. You have to turn off the policy and then turn it on for it to work properly. XG430 (SFOS 17.0…

I am not sure if I always need NAT. Sometimes I do and sometimes I don't. My latest issue was two VLAN networks hanging off the LAN interface of the Sophos XG. I had the correct firewall rules in place but I couldn't get traffic to flow until I created…

Hi PPPOE is done on the XG and from ISP provides 10.222.250.5/32. We have a 213.150.X.X/29 from the ISP routed via 10.222.250.5. LAN has internet and DNAT works PAT works that's all good. How to register the sophos and add licenses because the…

Hello, I guess its basics, however cannot understand why traffic for directly connected interfaces are getting source natted by wan public ip. Set up is Sophos XG firewalls connected directly via HA DMZ interface and have assigned 10.238.238.0/30…

Hello guys! I would appreciate your help. I installed XG (long time Home user of the UTM), latest version as of today (SFOS 18.5.2 MR-2-Build380) My problem is that I want to access my cameras and I am creating a rule for the camera specific port…

Hello, I read what MASQ is doing and it sounds like PAT to me. Is there any difference between MASQ and PAT? Because hiding inside network or device? PAT does the same thing. Thank you.

Hi Team, How do I NAT or PAT to a hostname instead of an ip address? #Nali

Nat issue

Hello. We have Wi-fi -> Access Point -> Router -> Sophos FW. I just want to know is it possible to use DMZ without Masquerading? Because we need to actually control what kind of content each of the users access using the Sophos. As you guys…

Hello, I have this situation: Our network: ip 10.10.10.0/24 External parter A: ip 10.20.20.0/24 (managed on another firewall different from Sophos) External Partnet B: ip 10.20.20.0/24 (same ip of partner A). I have a vpn working with B and I…

Sir, I have configured PortF1 for WAN Acees, which works perfectly fine with NATTING with our LAN and DMZ network. However I want to ctlreaye SSH acces from a WAN server to Two Serverd placed in DMZ. If my WAN client is 155.48.96.59 and I want to…

I'm finishing the deployment of a Sophos XGS 136 client, some NAT publications were made so that both externally and internally, users can access the web server (http) and the DVR that manages the surveillance cameras, everything ok. But I also created…

Hi, Good day all i have Sophos XG 135 Firewall setup with three incoming ISPs connection for three of my three VLAN groups. However, recently after the recent upgrade of firewall firmware. I found that the connection seems messed up. Its currently…

Hi all I have a requirement to split NATing between different users in my office. I managed to configure this successfully but after going live some PCs have access to the internet while some do not. On the Log viewer, the ones that do not have access…

I was hoping for those whom work with Sophos XG firewalls could provide some feedback. We have a few in deployment, but on version 16 and 17 of their firmware have hit a number of issues this includes but not limited to; NAT rules not working…